DTC Chart
DTC CHART
Power steering systemDTC No. | Detection Item | DTC Detection Condition | Warning indicated | Return to normal state | Note | Link |
|---|---|---|---|---|---|---|
C1511 |
Torque sensor 1 |
Torque sensor malfunction |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned back to ON |
- |
|
C1512 |
Torque sensor 2 |
Torque sensor malfunction |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned back to ON |
- |
|
C1513 |
Excessive torque sensor deviation |
Torque sensor malfunction |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned back to ON |
- |
|
C1514 |
Torque sensor power supply voltage |
Torque sensor malfunction |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1515 |
Torque sensor zero point calibration not performed |
This DTC is stored when the torque sensor zero point calibration has not been performed. |
EPS warning light comes on |
Zero point calibration is performed, or the ignition switch is turned to ON |
There is no malfunction if this DTC is not output again after performing the zero point calibration. |
|
C1516 |
Torque sensor zero point calibration incomplete |
The torque sensor zero point calibration is incomplete because the steering wheel was touched during calibration. |
EPS warning light comes on |
Ignition switch turned to ON again |
There is no malfunction if this DTC is not output again after clearing the DTC and the torque sensor calibration value and performing the zero point calibration. |
|
C1517 |
Torque hold |
Torque sensor malfunction |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1521 |
Short circuit in the electric motor circuit |
Motor overcurrent |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1522 |
Power supply sensor |
Motor current sensor malfunction |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1523 |
Excessive current deviation |
Current deviation excessively large |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1528 |
Motor rotation angle sensor |
Motor rotation angle sensor malfunction |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1531 |
ECU malfunction |
Internal ECU malfunction (CPU malfunction) |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned to ON |
- |
|
C1532 |
ECU malfunction |
Internal ECU malfunction (Peripheral circuit malfunction) |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1533 |
The voltage in the temperature sensor circuit is low or high |
Internal ECU malfunction (Auxiliary temperature sensor malfunction) |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1534 |
EEPROM |
Internal ECU malfunction (EEPROM error) |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1541 |
Vehicle speed signal |
The vehicle speed signals via the CAN communication system are interrupted for at least 3 seconds. |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned to ON |
- |
|
C1551 |
IG power supply voltage |
Open or short circuit in the IG power supply circuit with the ignition switch in the ON (IG) position |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned to ON |
- |
|
C1552 |
PIG power supply voltage |
PIG power supply circuit malfunction |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1554 |
Power supply relay failure |
Malfunction in the power supply source relay circuit |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1555 |
Motor relay welding failure |
Motor relay circuit malfunction |
EPS warning light: comes on |
Ignition switch turned to ON again |
- |
|
C1567 |
ECU matching error |
There is an error in the recognition system |
EPS warning light comes on |
Ignition switch turned to ON again |
- |
|
C1581 |
Assist card number not written |
The assist card is not written in the power steering ECU assembly |
EPS warning light comes on |
Assist card writing is performed, or the ignition switch is turned to ON |
- |
|
C1582 |
The assist card number does not match |
The assist card number does not match |
EPS warning light does not come on |
Assist card writing is performed, or the ignition switch is turned to ON |
- |
|
U0100 |
Loss of communication with ECM / PCM "A" |
Loss of communication with ECM |
EPS warning light does not come on |
The ECU determines that the system has returned to normal, or the ignition switch is turned to ON |
- |
|
U0129 |
Communication lost with brake control module |
Loss of communication with skid control ECU (brake actuator assembly) |
EPS warning light comes on |
The ECU determines that the system has returned to normal, or the ignition switch is turned to ON |
- |
|
U023A |
Loss of communication with front camera module |
Loss of communication with forward recognition camera |
EPS warning light does not come on |
The ECU determines that the system has returned to normal, or the ignition switch is turned to ON |
with Toyota Safety Sense P system |
.gif)