Power Steering Assist Systems

Data List / Active Test

~15min read
0102030405000N·mlb·ft
Tightening torque found on this page

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / EMPS / Data List.

(f) Read the Data List according to the Techstream display.

Chassis > EMPS > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Meter Vehicle Velocity

Speedometer vehicle speed

Min.: 0 km/h

Max.: 300 km/h

  • 0 km/h: engine running and vehicle stationary
  • No significant change: Engine running and vehicle moving at constant speed

-

Wheel Speed Right

Right rear wheel rotation speed

Min.: 0 km/h

Max.: 255 km/h

  • 0 km/h: engine running and vehicle stationary
  • No significant change: Engine running and vehicle moving at constant speed

-

Wheel Speed Left

Left rear wheel rotation speed

Min.: 0 km/h

Max.: 255 km/h

  • 0 km/h: engine running and vehicle stationary
  • No significant change: Engine running and vehicle moving at constant speed

-

Engine Revolution

Engine speed

Min.: 0 rpm

Max.: 12,800 rpm

No significant change

Engine runs at constant speed

Motor Actual Current

Amount of current supplied to the motor

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

- Value increases when turning left and decreases when turning right

Engine running and steering wheel turned

Command Value Current

Current required to the motor

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

- Value increases when turning left and decreases when turning right

Engine running and steering wheel turned

Steering Angle Velocity

Steering angle speed

Min.: -32,768 deg/s

Max.: 32,767 deg/s

Value changes in proportion to steering speed

- Value increases when turning left and decreases when turning right

Engine running and steering wheel turned

Thermistor Temperature

ECU board temperature

Min.: -50.0 °C

Max.: 150 °C

-50°C à 150 °C

-

IG Power Supply

IG power supply voltage

Min.: 0.0000 V

Max.: 20.1531 V

8 à 16 V

Ignition Switch in ON position

Steering Angle Sens Sig

Steering Angle Sensor Signal Status

OK or NG(1) or NG(2) or NG(3)

OK: Steering angle sensor signal received

NG (1): Learning is not completed

NG (2): Steering angle sensor abnormal

NG (3): Communication error

-

Steering Wheel Torque

Steering wheel torque

Min.: -7.0 N·m

Max.: 7 N·m

Value changes in proportion to steering effort

- Value increases when turning left and decreases when turning right

Engine running and steering wheel turned

Motor Rotation Angle

Motor rotation angle

Min.: 0.000 deg.

Max.: 360.000 deg.

Motor rotation angle varies from 0 to 360° during steering operation

Engine running and steering wheel turned

Command Val Current 2

Current required to the motor

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor Voltage

Motor power supply voltage

Min.: 0.000 V

Max.: 98.000 V

  • Approx. 27 V: Engine running and steering wheel turned
  • Approx. 27 to 34 V: Engine running and steering wheel not turned

-

TRQ1 Zero Point Value

Torque sensor 1 zero point value

Min.: 0.0000 V

Max.: 4.9725 V

2,3 à 2,7 V

Engine running and steering wheel not turned (no load)

TRQ2 Zero Point Value

Torque sensor 2 zero point value

Min.: 0.0000 V

Max.: 4.9725 V

2,3 à 2,7 V

Engine running and steering wheel not turned (no load)

IG ON/OFF Times

Number of times the ignition switch has been turned ON/OFF since the last DTC detection

Min.: 0 times

Max.: 65,535 times

-

-

Motor Overheat Record

Continuous Motor Overheat Prevention Control Record

Unrec or Rec

Unrec

Unrec: Not recorded

Rec: Recorded

The steering assist amount may decrease to prevent the motor and ECUs from overheating if the steering wheel is continuously operated while the vehicle is stopped or driven at low speed, or if the steering wheel is held at the lock position for a long time.

Motor Low Power Record

PIG Power Supply Voltage Drop Record

Unrec or Rec

Unrec

Unrec: Not recorded

Rec: Recorded

If the PIG power supply voltage temporarily drops, the steering assist amount will be reduced.

Eng Rev Inter Record

Engine Speed Signal Interruption Record

Unrec or Rec

Unrec

Unrec: Not recorded

Rec: Recorded

Str Angle Inter Record

Steering Angle Sensor Signal Interruption Occurrence Screen Record

Unrec or Rec

Unrec

Unrec: Not recorded

Rec: Recorded

Spd Sig Invalid Record

Invalid Vehicle Speed Signal Record

Unrec or Rec

Unrec

Unrec: Not recorded

Rec: Recorded

Battery Voltage Lo Record

Battery Voltage Drop History

Min.: 0 times

Max.: 65,535 times

0 to 65,535 times

-

Battery Control Count (Body ECU)

Battery Charge Control Usage Count

Min.: 0 times

Max.: 65,535 times

-

-

PS Assist Signal

Power steering assist signal recording status

OFF or ON

OFF: Ignition switch in ON position

ON: Engine running

-

Motor Actual Current 2

Amount of current supplied to the motor

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Stop&Start Ctrl Mode

Stop & start control mode recording status

IG, Run, Stopreq, Stop, Restart

IG: Ignition switch in ON position (before engine start)

Run: Engine running

Stopreq: Engine stop request

Stop: Engine stopped

Restart: Engine restart

-

Motor Overheat Limit Cnt(Normal)

Number of times the assist limit was applied based on the estimated temperature of the electric motor coil and the heat-generating components of the EPS ECU assembly

Min.: 0 times

Max.: 255 times

-

-

Assist Limit Cnt(Power Voltage Low)

Number of times the assist limit was applied due to a battery voltage drop to 9 V or below

Min.: 0 times

Max.: 255 times

-

-

Power Vol Low Prevention Limit Cnt

Number of times the assist limit was applied due to a battery voltage drop to 9.7 V or below

Min.: 0 times

Max.: 255 times

-

-

Eng Stall/Ready OFF Cnt

Number of times the assist limit was applied after the engine stalled and the ignition switch was turned OFF

Min.: 0 times

Max.: 255 times

-

-

Motor Overheat Limit Cnt(Motor Overload)

Number of times the assist limit was applied to prevent system overheating when the electric motor was overloaded because the steering wheel was held at full lock or one of the tires hit a curb

Min.: 0 times

Max.: 255 times

-

-

Assist Limit Cnt(Vehicle Spd Sig Malf)

Number of times the assist power was adjusted to a level suitable for high-speed driving when high speed was detected due to an abnormal vehicle speed signal

Min.: 0 times

Max.: 255 times

-

-

Assist Limit Record 1

Assist limit information used in the past or currently in use (most recent history)

Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep

-

-

Record 1 Key Cycle

Number of times the ignition switch was turned ON before assist limit Record 1 was stored

Min.: 0 times

Max.: 65,535 times

-

-

Record 1 Key Cycle Elapsed Time

Elapsed time after the ignition switch was turned ON before assist limit Record 1 was stored

Min.: 0.0 s

Max.: 53,687,091.0 s

-

-

Record 1 Power Source

Power source operating status when assist limit Record 1 was stored

No Data, Running, Stop

-

-

Assist Limit Record 2

Assist limit information used in the past (second most recent history)

Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep

-

-

Record 2 Key Cycle

Number of times the ignition switch was turned ON after Record 2 was stored and before assist limit Record 1 was stored

Min.: 0 times

Max.: 65,535 times

-

-

Record 2 Key Cycle Elapsed Time

Elapsed time after the ignition switch was turned ON before assist limit Record 2 was stored

Min.: 0.0 s

Max.: 53,687,091.0 s

-

-

Record 2 Power Source

Power source operating status when assist limit Record 2 was stored

No Data, Running, Stop

-

-

Assist Limit Record 3

Assist limit information used in the past (third most recent history)

Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep

-

-

Record 3 Key Cycle

Number of times the ignition switch was turned ON after Record 3 was stored and before assist limit Record 2 was stored

Min.: 0 times

Max.: 65,535 times

-

-

Record 3 Key Cycle Elapsed Time

Elapsed time after the ignition switch was turned ON before assist limit Record 3 was stored

Min.: 0.0 s

Max.: 53,687,091.0 s

-

-

Record 3 Power Source

Power source operating status when assist limit Record 3 was stored

No Data, Running, Stop

-

-

Steering Angle

Steering angle

Min.: -3,072.0 deg.

Max.: 3,070.5 deg.

-

-

Torque Sensor 1 Output

Torque sensor 1 output value

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Torque Sensor 2 Output

Torque sensor 2 output value

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Torque Sensor 1 Power Supply

Torque sensor 1 power supply voltage

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Torque Sensor 2 Power Supply

Torque sensor 2 power supply voltage

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Rotation Angle Sensor Output 1

Rotation angle sensor output voltage Vx1

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Rotation Angle Sensor Output 2

Rotation angle sensor output voltage Vx2

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Rotation Angle Sensor Output 3

Rotation Angle Sensor Output Voltage Vy1

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Rotation Angle Sensor Output 4

Rotation Angle Sensor Output Voltage Vy2

Min.: 0.0000 V

Max.: 4.9725 V

-

-

Motor 1 Terminal Current (U)

Motor 1 Terminal Current (U Phase)

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor 1 Terminal Current (V)

Motor 1 Terminal Current (V Phase)

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor 1 Terminal Current (W)

Motor 1 Terminal Current (W Phase)

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor 2 Terminal Current (U)

Motor 2 Terminal Current (U Phase)

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor 2 Terminal Current (V)

Motor 2 Terminal Current (V Phase)

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor 2 Terminal Current (W)

Motor 2 Terminal Current (W Phase)

Min.: -327.68 A

Max.: 327.67 A

Value changes in proportion to steering effort

Engine running and steering wheel turned

Motor 1 U Phase Duty

Motor 1 U Phase Duty

Min.: 0.00 %

Max.: 100.00 %

-

-

Motor 1 V Phase Duty

Motor 1 V Phase Duty

Min.: 0.00 %

Max.: 100.00 %

-

-

Motor 1 W Phase Duty

Motor 1 W Phase Duty

Min.: 0.00 %

Max.: 100.00 %

-

-

Motor 2 U Phase Duty

Motor 2 U Phase Duty

Min.: 0.00 %

Max.: 100.00 %

-

-

Motor 2 V Phase Duty

Motor 2 V Phase Duty

Min.: 0.00 %

Max.: 100.00 %

-

-

Motor 2 W Phase Duty

Motor 2 W Phase Duty

Min.: 0.00 %

Max.: 100.00 %

-

-

Motor 1 Terminal Voltage (U)

Motor 1 Terminal Voltage (U Phase)

Min.: 0.000 V

Max.: 98.000 V

Value varies in the range of 4 to 35 V

Engine running and steering wheel turned

Motor 1 Terminal Voltage (V)

Motor 1 Terminal Voltage (V Phase)

Min.: 0.000 V

Max.: 98.000 V

Value varies in the range of 4 to 35 V

Engine running and steering wheel turned

Motor 1 Terminal Voltage (W)

Motor 1 Terminal Voltage (W Phase)

Min.: 0.000 V

Max.: 98.000 V

Value varies in the range of 4 to 35 V

Engine running and steering wheel turned

Motor 2 Terminal Voltage (U)

Motor 2 Terminal Voltage (U Phase)

Min.: 0.000 V

Max.: 98.000 V

Value varies in the range of 4 to 35 V

Engine running and steering wheel turned

Motor 2 Terminal Voltage (V)

Motor 2 Terminal Voltage (V Phase)

Min.: 0.000 V

Max.: 98.000 V

Value varies in the range of 4 to 35 V

Engine running and steering wheel turned

Motor 2 Terminal Voltage (W)

Motor 2 Terminal Voltage (W Phase)

Min.: 0.000 V

Max.: 98.000 V

Value varies in the range of 4 to 35 V

Engine running and steering wheel turned

Motor 1 PIG Power Supply

Power supply voltage for driving Motor 1

Min.: 0.0000 V

Max.: 20.1531 V

9 à 16 V

Engine running and steering wheel turned

Motor 2 PIG Power Supply

Power supply voltage for driving Motor 2

Min.: 0.0000 V

Max.: 20.1531 V

9 à 16 V

Engine running and steering wheel turned

The Number of DTCs

Number of DTCs detected when freeze frame data was stored

Min.: 0

Max.: 255

0 à 255

-

HINT:

  • When the vehicle is stationary or moving very slowly, if the steering wheel is turned repeatedly or held at full lock for an extended period, the steering assist amount will be reduced to prevent overheating of the motor and ECU. In this case, leave the engine running and do not turn the steering wheel for about 10 minutes to allow steering assist to recover.
  • When the battery is not sufficiently charged or the voltage temporarily drops, the steering assist amount is reduced and the EPS warning light comes on. In this case, the steering assist force returns to normal when the battery voltage is restored.