General information on paint

1K corrosion protection primer

2steps
~22min
3/5difficulty
2special tools
Done 0 of 2

Designation:

  • 1K corrosion protection primer -LLS MAX 003 M2- color red-brown

Product description

The 1K corrosion protection primer -LLS MAX 003 M2- is a zinc chromate-free single-component product from the PVB system.

Suitable for use as a wash primer on all common metal substrates.

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Features:

  • Good corrosion protection properties
  • Easy handling (1K material)

Application information

Substrate

Suitable substrates:

  • Bare sheet steel, sanded
  • cleaned and sanded, electrogalvanized steel panels or soft aluminum
  • well-sanded original or refinish paint (except thermoplastic coating)
  • Original replacement part primer, sanded
  • surfaces pre-worked with 2K polyester products and then finely sanded


Note

Due to the variety of alloys and manufacturing processes for metals, a preliminary test on the respective substrate is required to ensure the pretreatment is sufficient for perfect adhesion.

Pretreatment of substrates:

- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Sand the factory or old paint finish.

- Thoroughly remove any rust spots and feather the edges into the old paint finish.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Application:

- Shake the can thoroughly for at least 2 minutes.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

- Apply 2 spray coats with a flash-off time of 5-10 minutes between coats.

Spray distance:

- Maintain a spray distance of 20-25 cm.

- The recommended dry film thickness is 15-20 µm.


Note

If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

VW UP. Allgemeine Informationen Lack

Drying

Drying time at +20 °C room temperature is 10-20 minutes.

VW UP. Allgemeine Informationen Lack

Overcoating

Can be overcoated with:

  • 2K HS primer-surfacer (for processing, see the relevant technical information)
  • 2K HS topcoat
  • Waterborne basecoat and 2K HS clearcoat


Note

  • Do not recoat with polyester products or epoxy products.
  • Do not use over thermoplastic coatings.
  • Do not recoat directly with waterborne basecoat.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Shake briefly again before each further spray coat.

Dispose of empty spray cans as recyclable material.

Characteristics


Storage

The guaranteed storage stability is 60 months from the date of production. Usable until the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

1K control coat

Designation:

  • 1K control coat -LLS MAX 005-, color black

Product description

The 1K control coat -LLS MAX 005- is a single-component product made from special NC resin combinations.

Features:

  • Easy processing (1K material)
  • fast drying
  • High yield
  • Good hiding power
  • Even application
  • Easy to sand

Application information

Application

Detection of surface irregularities on primer and primer-surfacer substrates.

Substrate

Suitable substrates:

  • All primers unsanded
  • All primer-surfacer applications unsanded.

Pretreatment of substrates:

- Clean carefully with silicone remover -LLS MAX 007- or long silicone remover -LLS MAX 0008-.

VW UP. Allgemeine Informationen Lack

Processing

Wear suitable personal protective equipment in accordance with occupational safety regulations.

  • Protective gloves, e.g. made of latex or nitrile
  • Respirator, e.g. type A2/P2

Application:

- Shake the can thoroughly for at least 2 minutes and briefly "test spray".

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

- Apply 1 mist coat, thin and even.

- The recommended dry film thickness is 15 µm.

Spray distance:

- Maintain a spray distance of 20-25 cm.


Note

If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

VW UP. Allgemeine Informationen Lack

Drying

Drying time at +20 °C room temperature is 10 minutes. Infrared drying is possible with this product.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Shake briefly again before each further spray coat.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 60 months from the date of production. Usable until the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

1K clear coat

Designation:

  • 1K clear coat -LLS MAX 010-

Product description

The 1K clear coat -LLS MAX 010- is a single-component product. The raw material base is acrylic resin.

Features:

  • Easy processing (1K material)
  • fast drying
  • High gloss
  • Universally applicable
  • Easy to polish

Application information

Application

Repair work and partial painting

Substrate

Suitable substrates:

  • Solvent-based or water-based basecoats
  • The basecoat can be overcoated with 1K clear coat -LLS MAX 010- after 30 minutes of drying.

Pretreatment of substrates:

- The substrate must be free of dust and grease.

VW UP. Allgemeine Informationen Lack

Processing

Wear suitable personal protective equipment in accordance with occupational safety regulations.

  • Protective gloves, e.g. made of latex or nitrile
  • Respirator, e.g. type A2/P2

Application:

- Shake the can thoroughly for at least 2 minutes and briefly "test spray".

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

- Apply 2-3 spray coats with a flash-off time of 5-10 minutes between coats.

- The recommended dry film thickness is 30-40 µm.

Spray distance:

- Maintain a spray distance of 20-25 cm.


Note

If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

VW UP. Allgemeine Informationen Lack

Drying

Air drying at +20 °C room temperature:

  • Dust-dry after 10 minutes
  • Tack-free after 20 minutes
  • Polishable after 12 hours
VW UP. Allgemeine Informationen Lack

Infrared drying is possible with this product. Infrared drying time with a short-wave emitter is 7 minutes.

Further processing

- The 1K clear coat -LLS MAX 010- can be polished with commercially available polishes after 12 hours of air drying at +20 °C room temperature.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Shake briefly again before each further spray coat.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 60 months from the date of production. Usable until the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

1K wash primer

Designation:

  • 1K wash primer -LLS MAX 106 M2-, color light grey
  • 1K wash primer -LLS MAX 107 M2-, color dark grey

Product description

The 1K wash primers -LLS MAX 106/107 M2- are zinc chromate-free single-component products from the PVB system.

Suitable for use as a wash primer on all common metal substrates.

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Features:

  • Good corrosion protection properties
  • Easy handling (1K material)
  • Available in two shades of grey

Application information

Substrate

Suitable substrates:

  • Bare sheet steel, sanded
  • cleaned and sanded, electrogalvanized steel panels or soft aluminum
  • well-sanded original or refinish paint (except thermoplastic coating)
  • surfaces pre-worked with 2K polyester products and then finely sanded


Note

Due to the variety of alloys and manufacturing processes for metals, a preliminary test on the respective substrate is required to ensure the pretreatment is sufficient for perfect adhesion.

Pretreatment of substrates:

- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Sand the factory or old paint finish.

- Thoroughly remove any rust spots and feather the edges into the old paint finish.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Application:

- Shake the can thoroughly for at least 2 minutes.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

- Apply 1-3 spray coats with a flash-off time of 5-10 minutes between coats.

When used as a wash primer:

- Apply 1-2 spray coats with a flash-off time of 5-10 minutes between coats.

Spray distance:

- Maintain a spray distance of 20-25 cm.

- The recommended dry film thickness is 10-20 µm.

Sealing small sanding-through spots (no larger than Ø 5.0 cm):


Note

  • Waterborne basecoats and 2K HS topcoats may only be applied wet-on-wet and in the scuff-sanding process over the 1K wash primer if the sanded-through spot is no larger than Ø 5.0 cm. Application can be made in 1-3 spray coats, with a dry film thickness of 10-40 µm.
  • If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.
VW UP. Allgemeine Informationen Lack

Drying

Drying time at +20 °C room temperature is 10-20 minutes. The material can be sanded after 45-60 minutes.

Can be overcoated with:

  • 2K acrylic primer-surfacer after 10-15 minutes.
  • 2K HS topcoat (only for small sand-through spots) after 10-15 minutes.
  • Waterborne basecoat (only for small sand-through spots) after 20-30 minutes.
VW UP. Allgemeine Informationen Lack

Overcoating

  1. When used as wash primer, can be overcoated with 2K HS filler.
  2. Use as wash primer to seal small sand-through spots:
    VW UP. Allgemeine Informationen Lack

- Wet sanding with abrasive paper grit P 800-1000

Can be overcoated with:

  • 2K HS topcoat (only for small sanded-through spots)
  • Waterborne basecoat and 2K HS clearcoat (only for small sanded-through spots)


Note

  • Do not recoat with polyester products or epoxy products.
  • Do not use over thermoplastic coatings.
  • Not dry-sandable.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Shake briefly again before each further spray coat.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 60 months from the date of production. Usable until the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

1K Fill-Clean spray can -LLS MAX 099-, -LLS MAX 100-, Aquaplus system

Designation:

  • 1K Fill-Clean spray can -LLS MAX 099-, 250 ml for waterborne mixing paint "Aquaplus system"
  • 1K Fill-Clean spray can -LLS MAX 100-, 400 ml for waterborne mixing paint "Aquaplus system"

Product description

These products are spray cans pre-filled with a propellant and solvent combination specially matched to the "Aquaplus system" and "Aqua Premium system".

Only the Fill-Clean filling device may be used for filling.

Scope of application: Clever-Repair only.

Handling notes

This product is a spray can pre-filled with a propellant and solvent combination specially matched to the "Aquaplus system" and "Aqua Premium system".

This can does not yet contain any paint material. It is a semi-finished product.

The ready-to-use end product is created by filling 100 ml of undiluted Aquaplus or Aqua Premium basecoat using the dedicated Fill-Clean filling device.

Before passing on a ready-to-use spray can filled with paint, it must be relabeled. This can be done, for example, using a shade label generated and printed with the formula program of the mixing bank.

Make sure the label contains the information shown in the example below.

  • The content specification of 316 ml (0.32 L) on the label corresponds to a fully filled spray can.
  • It contains 216 ml of pre-filling with propellant and solvent, plus 100 ml of subsequently filled Aquaplus or Aqua Premium basecoat incl. additive for Aqua Premium -LVM 035 200- or additive for Aqua Premium -LVM 035 301-.


Note

  • Wear suitable personal protective equipment in accordance with occupational safety regulations.
  • Set up the device in a well-ventilated room.
  • Do not fill the filling cans beyond their maximum capacity. Risk of explosion!
  • Never use toxic or carcinogenic substances or halogenated hydrocarbons to fill the spray cans.
  • Caution: electrostatic charges. Clean plastic parts only with a damp cloth.
  • All repair work must be carried out by a qualified specialist.
  • Paint residues on the device should be cleaned at regular intervals with a cloth and a suitable solvent.
  • Check the condition of the compressed air supply line regularly.

Fill-Clean filling procedure

Observe the operating instructions of the filling device.

- Place the filling pad on the press-in plunger.

VW UP. Allgemeine Informationen Lack

- Place the Fill-Clean filling cylinder onto the spray can.

VW UP. Allgemeine Informationen Lack

- Fit and press down the Fill-Clean cap.

VW UP. Allgemeine Informationen Lack

- Filling with paint

VW UP. Allgemeine Informationen Lack

- Insert the Fill-Clean can with the filled filling cylinder into the upper slot -1- of the Fill-Clean device.


Note

The lower turntable -2- must be fully at the bottom before the Fill-Clean can is inserted into the upper slot -1-. If the Fill-Clean can is in the upper slot -1-, turn the turntable -2- upward as a counter-holder.

VW UP. Allgemeine Informationen Lack

- Slide the cover with the button to the right to start filling. Duration approx. 10 seconds.

VW UP. Allgemeine Informationen Lack

- After filling, remove the filling cylinder -2- from the Fill-Clean can.

- Remove the Fill-Clean cap -1- from the filling cylinder -2-.

- Fit spray head -3- onto the Fill-Clean can.

VW UP. Allgemeine Informationen Lack

- The pad remains in the Fill-Clean cap for shade reference.

- The Fill-Clean can is now ready to use.

Application information

Substrate

Suitable substrates:

  • 2K HS filler
  • Intact existing paint
  • 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-
  • 2K plastic adhesion primer -LKF 696 009 A2-/-LKF 696 040 A2-
  • for plastic surfaces, see
VW UP. Allgemeine Informationen Lack

Pretreatment of substrates:

- Thoroughly clean OEM or existing paint, or 2K HS filler, with silicone remover -LSW 019 000 A5-. For heavy contamination, first clean with silicone remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with a dual-action sander and dust extraction, P 400-500.

VW UP. Allgemeine Informationen Lack

- Or wet sanding with abrasive paper grit P 800-1000.

VW UP. Allgemeine Informationen Lack

- Before refinishing, thoroughly clean the sanded substrates again with silicone remover -LSW 019 000 A5- to remove dust, sanding residue and other contamination.

1) Special notes:

  • Wipe off excess silicone remover with a lint-free cloth to avoid streaks. See technical application information "Silicone remover".
  • Sand-through spots must be primed with 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-.
  • Sand-through spots must not be larger than Ø 5.0 cm.
  • When using 2K HS filler, bare spots must be primed with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-.
  • Creating a spray-out panel before application is recommended.
VW UP. Allgemeine Informationen Lack

Processing

Application:

- Shake the can thoroughly for at least 2 minutes to ensure complete mixing.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

Spray distance:

- Maintain a spray distance of 20-25 cm.

- The recommended dry film thickness is 15-20 µm.

VW UP. Allgemeine Informationen Lack

- Apply 2 coats (1 normal coat + 1 finish/effect coat) with a 5-10 minute flash-off time between coats.


Note

  • For poorly covering shades, a further coat (wet-on-wet) may be necessary.
  • Alternatively, flash off to a matte finish between coats.
  • After finishing or interrupting spraying, spray the valve empty while holding the can upside down to prevent the nozzle from clogging.
VW UP. Allgemeine Informationen Lack

Drying

Drying time at a room temperature of +20 °C is 15-30 minutes. Important: allow to flash off to matte.

Can be overcoated with:

  • 2K HS clearcoat (see respective data sheet).
  • 2K clearcoat -LLS MAX 210- (overcoating with other 2K HS clearcoats is possible)


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

After filling, shake the can for approx. 2 min.

Before use, shake the can for approx. 2 min.

Shake briefly again before each further spray coat.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of spray cans pre-filled only is 24 months.

The guaranteed storage stability of spray cans filled with paint is 4 weeks.

VW UP. Allgemeine Informationen Lack

1K Fill-Clean spray can -LLS MAX 112-, Aqua Premium system

  • 1K Fill-Clean spray can -LLS MAX 112-, 400 ml for waterborne mixing paint "Aqua Premium system"

Product description

These products are spray cans pre-filled with a propellant and solvent combination specially matched to the "Aquaplus system" and "Aqua Premium system".

Only the Fill-Clean filling device may be used for filling.

Scope of application: Clever-Repair only.

Handling notes

This product is a spray can pre-filled with a propellant and solvent combination specially matched to the "Aquaplus system" and "Aqua Premium system".

This can does not yet contain any paint material. It is a semi-finished product.

The ready-to-use end product is created by filling 100 ml of undiluted Aquaplus or Aqua Premium basecoat using the dedicated Fill-Clean filling device.

Before passing on a ready-to-use spray can filled with paint, it must be relabeled. This can be done, for example, using a shade label generated and printed with the formula program of the mixing bank.

Make sure the label contains the information shown in the example below.

Content specification and pre-filling

  • The content specification of 316 ml (0.32 L) on the label corresponds to a fully filled spray can.
  • It contains 294 ml pre-filled with propellant and solvent, plus 100 ml of subsequently filled, ready-to-spray Aqua Premium base coat including additive for Aqua Premium -LVM 035 200- or additive for Aqua Premium -LVM 035 301-.


Note

  • Wear suitable personal protective equipment in accordance with occupational safety regulations.
  • Set up the device in a well-ventilated room.
  • Do not fill the filling cans beyond their maximum capacity. Risk of explosion!
  • Never use toxic or carcinogenic substances or halogenated hydrocarbons to fill the spray cans.
  • Caution: electrostatic charges. Clean plastic parts only with a damp cloth.
  • All repair work must be carried out by a qualified specialist.
  • Paint residues on the device should be cleaned at regular intervals with a cloth and a suitable solvent.
  • Check the condition of the compressed air supply line regularly.

Mixing notes for "Aqua Premium system"


Fill-Clean filling procedure

Observe the operating instructions of the filling device.

- Place the filling pad on the press-in plunger.

VW UP. Allgemeine Informationen Lack

- Place the Fill-Clean filling cylinder onto the spray can.

VW UP. Allgemeine Informationen Lack

- Fit and press down the Fill-Clean cap.

VW UP. Allgemeine Informationen Lack

- Fill with paint.

VW UP. Allgemeine Informationen Lack

- Insert the Fill-Clean can with the filled filling cylinder into the upper slot -1- of the Fill-Clean device.


Note

The lower turntable -2- must be fully at the bottom before the Fill-Clean can is inserted into the upper slot -1-. If the Fill-Clean can is in the upper slot -1-, turn the turntable -2- upward as a counter-holder.

VW UP. Allgemeine Informationen Lack

- Slide the cover with the button to the right to start filling. Duration approx. 10 seconds.

VW UP. Allgemeine Informationen Lack

- After filling, remove the filling cylinder -2- from the Fill-Clean can.

- Remove the Fill-Clean cap -1- from the filling cylinder -2-.

- Fit spray head -3- onto the Fill-Clean can.

VW UP. Allgemeine Informationen Lack

- The pad remains in the Fill-Clean cap for shade reference.

- The Fill-Clean can is now ready to use.

Application information

Substrate

Suitable substrates:

  • 2K HS filler
  • Intact existing paint
  • 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-
  • 2K plastic adhesion primer -LKF 696 009 A2-/-LKF 696 040 A2-
  • for plastic surfaces, see
VW UP. Allgemeine Informationen Lack

Pretreatment of substrates:

- Thoroughly clean OEM or existing paint, or 2K HS filler, with silicone remover -LSW 019 000 A5-. For heavy contamination, first clean with silicone remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Sand dry with a random orbital sander and dust extraction, P 500.

VW UP. Allgemeine Informationen Lack

- Or wet sanding with abrasive paper grit P 800-1000.

VW UP. Allgemeine Informationen Lack

- Before refinishing, thoroughly clean the sanded substrates again with silicone remover -LSW 019 000 A5- to remove dust, sanding residue and other contamination.

1) Special notes:

  • Wipe off excess silicone remover with a lint-free cloth to avoid streaks. See technical application information "Silicone remover".
  • Sand-through spots must be primed with 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-.
  • Sand-through spots must not be larger than Ø 5.0 cm.
  • When using 2K HS filler, bare spots must be primed with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-.
  • Creating a spray-out panel before application is recommended.
VW UP. Allgemeine Informationen Lack

Processing

Application:

- Shake the can thoroughly for at least 2 minutes to ensure complete mixing.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

Spray distance:

- Maintain a spray distance of 20-25 cm.

- The recommended dry film thickness is 15-20 µm.

VW UP. Allgemeine Informationen Lack

- Apply 2 coats (1 normal coat + 1 finish/effect coat) with a 5-10 minute flash-off time between coats.

- The recommended dry film thickness is approx. 15-20 μm.


Note

  • For poorly covering shades, a further coat (wet-on-wet) may be necessary.
  • Alternatively, flash off to a matte finish between coats.
  • After finishing or interrupting spraying, spray the valve empty while holding the can upside down to prevent the nozzle from clogging.
VW UP. Allgemeine Informationen Lack

Drying/Recoating

Flash-off time before applying clear coat is 15-30 minutes at +20 ºC room temperature. Important: Allow to flash off matte.

Can be overcoated with:

  • 2K HS clearcoat (see respective data sheet).
  • 2K clearcoat -LLS MAX 210- (overcoating with other 2K HS clearcoats is possible)


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

After filling, shake the can for approx. 2 min.

Before use, shake the can for approx. 2 min.

Shake briefly again before each further spray coat.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of spray cans pre-filled only is 24 months.

The guaranteed storage stability of spray cans filled with paint is 1 week.

VW UP. Allgemeine Informationen Lack