2K Filler
Designation:
- 2K Filler -LLS MAX 202 M2-, colour medium grey
Product description
The 2K filler -LLS MAX 202 M2-, colour medium grey, is a very high-quality 2K HS sanding filler. The raw material base is acrylic resin.
Features:
- constant atomizing pressure
- Aerosol distribution
- Long pot life
- Optimal and safe processing properties
- Excellent sag resistance
- Excellent sandability
- Very high yield
- Excellent filling power
- Area of application: Clever Repair
- professional paint finish
![]()
Note
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Application information
Substrate
Suitable substrates:
- Cleaned and sanded steel sheet primed with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-, galvanised or electrolytically galvanised steel sheet, or soft aluminium.
- Finely sanded, thoroughly cleaned original factory primer.
- Sanded factory or old paint (except TPA).
- Surfaces pre-treated with 2K polyester products and then finely sanded.
- Release-agent-free, cleaned and sanded UP-GF substrates.
Pretreatment of substrates:
- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

- Sand the factory or old paint finish.
- Thoroughly remove any rust spots and feather the edges into the old paint finish.

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

Processing
Activating the 2K spray can:
- Shake before use.

- Remove the red push button from the cap and place it on the hardener mixing valve on the underside of the can.

- Press in the hardener mixing valve. When pressing in the hardener mixing valve, make sure the can is upside down.

- Shake the can thoroughly for at least 2 minutes.

Processing/pot life:
- 8 hours at +20 ºC

Application method "Spray pass"
- Apply 2-3 opaque spray coats with 5-10 minutes flash-off time between coats.
Spray distance:
- Maintain a spray distance of 20-25 cm.
- The recommended dry film thickness is approx. 80-120 μm.
![]()
Note
If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

Drying
Air drying at +20 °C room temperature:
- At a dry film thickness of 80-120 μm, 3-4 hours.

The flash-off time for forced drying is at least 5-15 minutes.
Forced drying at +60 ºC object temperature at a film thickness of 80-120 μm takes 30-40 minutes.

The flash-off time for infrared drying is at least 5-10 minutes.

Infrared drying at a film thickness of 80-120 μm takes 10 minutes with a short-wave emitter and 15 minutes with a medium-wave emitter.

Further processing
- Dry sanding with random orbital sander and dust extraction, abrasive paper grit P400-500.

- Wet sanding with abrasive paper grit P800-1000

Overcoating
Can be overcoated with:
- 2K HS topcoat
- Waterborne basecoat and 2K HS clearcoat
![]()
Note
- Any small defects in the substrate can be "spot-filled" with 2K polyester filler.
- After drying and intermediate sanding, the filler spots can be sealed again with 2K epoxy primer-surfacer -LLS MAX 220 M1/M2- or a 2K HS Premium filler.
- The best sealing (including on critical substrates) is achieved with a medium film build of 80-120 μm in 2-3 spray coats, air-dried overnight or oven/infrared dried. On critical substrates, fine preparation is required and the parts must be filled over the entire surface.
- For sealing thermoplastic paint finishes we recommend 2K HS variable filler -LGF 786 004 A4-, grey.
![]()
Caution!
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Observe the safety data sheets and the warnings on the spray can label.
Shake briefly again before each further spray coat.
Dispose of empty spray cans as recyclable material.
![]()
WARNING!
- Ready-to-use coating materials containing isocyanates can irritate the mucous membranes (especially the respiratory organs) and trigger hypersensitivity reactions.
- Inhaling vapours or spray mist carries a risk of sensitisation.
- When handling isocyanate-containing coating materials, observe all measures for solvent-based coating materials carefully. In particular, do not inhale spray mist or vapours.
- Allergy sufferers, asthmatics and persons prone to respiratory disorders must not be assigned to work with isocyanate-containing coating materials.
Characteristics

Storage
The guaranteed storage stability is 36 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

2K clearcoat
Designation:
- 2K Clear Coat -LLS MAX 210-
Product description
The 2K clear coat -LLS MAX 210- is a high-gloss two-component clear coat for permanent sealing of painted surfaces. Specially developed for panel and repair painting. This product features permanent weather and chemical resistance, excellent petrol resistance and very good polishability. The 2K clear coat has very good flow and is generally used for larger areas (1-2 body panels). The raw material base is acrylic resin. The hardener contains isocyanate.
Features:
- constant atomizing pressure
- Aerosol distribution
- Excellent filling power
- Area of application: Spot repair within panel and repair painting
- professional paint finish
![]()
Note
- Wear appropriate personal protective equipment for occupational safety:
- Respirator type: A2/P2
- Protective gloves, e.g. made of latex or nitrile
Application information
Substrate
Suitable substrates:
- Solvent- and water-thinnable basecoat systems
- Old paint, cleaned and sanded

Processing
Activating the 2K spray can:
- Shake the can thoroughly for 2 minutes before activating.

- Remove the red push button from the cap and place it on the hardener mixing valve on the underside of the can.

- Press in the hardener mixing valve. When pressing in the hardener mixing valve, make sure the can (with cap) is upside down.

- After activating, shake the can thoroughly again for at least 2 minutes.

Processing/pot life:
- 48 hours at +20 ºC
![]()
Note
Pot life depends on ambient temperature. Higher temperatures shorten pot life, lower temperatures lengthen it.

Application method "Spray pass"
- Apply 1-2 opaque spray coats (30 μm per coat) with 10-15 minutes flash-off time, depending on temperature.
Spray distance:
- Maintain a spray distance of 20-25 cm.
![]()
Note
If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

Drying
Air drying at +20 ºC room temperature takes 12 hours.

The flash-off time for forced drying is at least 10-15 minutes.
Forced drying at +60 ºC object temperature takes 35-40 minutes.

The flash-off time for infrared drying is at least 10-15 minutes.

Infrared drying is recommended.
![]()
Caution!
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Observe the safety data sheets and the warnings on the spray can label.
Shake briefly again before each further spray coat.
Dispose of empty spray cans as recyclable material.
![]()
WARNING!
- Ready-to-use coating materials containing isocyanates can irritate the mucous membranes (especially the respiratory organs) and trigger hypersensitivity reactions.
- Inhaling vapours or spray mist carries a risk of sensitisation.
- When handling isocyanate-containing coating materials, observe all measures for solvent-based coating materials carefully. In particular, do not inhale spray mist or vapours.
- Allergy sufferers, asthmatics and persons prone to respiratory disorders must not be assigned to work with isocyanate-containing coating materials.
Characteristics


Storage
Guaranteed storage stability is 24 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 °C.

2K epoxy primer-surfacer
Designation:
- 2K Epoxy Primer Surfacer -LLS MAX 220 M1-, color beige (250 ml)
- 2K Epoxy Primer Surfacer -LLS MAX 220 M2-, color beige (400 ml)
Product description
The 2K Epoxy Primer Surfacer -LLS MAX 220 M1/M2- is a two-component epoxy aerosol can for use on small damaged areas. Do not use in areas directly exposed to stone chipping.
In the underbody area, the EP primer surfacer must be protected by trim panels, body covers, wheel arch liners or similar, and underbody protection material. Seal all hard-to-reach areas with wax underbody protection.
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Features:
- Versatile use
- good corrosion protection
Application information
Substrate
Suitable substrates:
- Bare sheet steel, sanded
- cleaned and sanded, electrogalvanized steel panels or soft aluminum
- properly sanded old or factory paint finish
- Original replacement part primer, sanded
- release-agent-free, cleaned and sanded UP-GF substrates
- surfaces pre-worked with 2K polyester products and then finely sanded
Pretreatment of substrates:
- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

- Then sand.

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.
![]()
Caution!
The 2K Epoxy Primer Surfacer -LLS MAX 220 M1/M2- must not be applied over PVB (acid-curing) adhesion primers or 1K primers (e.g. synthetic resin).

Processing
Application:
- Shake before use.

- Remove the red push button from the cap and place it on the hardener mixing valve on the underside of the can.

- Press in the hardener mixing valve. When pressing in the hardener mixing valve, make sure the can is upside down.

- Shake the can thoroughly for at least 2 minutes.

Processing/pot life:
- 8 hours at +20 ºC

Application method "Spray pass"
- Apply 2-3 spray coats with a flash-off time of 5-10 minutes between coats.
Spray distance:
- Maintain a spray distance of 20-25 cm.
Reaction temperature:
- Minimum +15 °C
- The recommended dry film thickness is 50-70 µm.
![]()
Note
If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

Drying
The flash-off time for forced drying is at least 5-15 minutes.

Forced drying at +60-65 °C object temperature with a film thickness of 50-70 µm takes 40-45 minutes.

Flash-off time before infrared drying is at least 10-20 minutes.

Infrared drying at a film thickness of 50-70 µm takes 3-5 minutes at 50% power with a short-wave emitter, followed by 15-20 minutes at 100% power.

Further processing
- Dry sanding with dual-action sander and dust extraction, abrasive paper grit P400-500

- Wet sanding with abrasive paper grit P800-1000

Overcoating
Can be overcoated with:
- 2K HS topcoat
- Waterborne basecoat and 2K HS clearcoat
![]()
Note
- Any small defects in the substrate can be "spot-filled" with 2K polyester filler.
- After drying and interim sanding, the filler spots can be sealed again with 2K Epoxy Primer Surfacer -LLS MAX 220 M1/M2-.
![]()
Caution!
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Observe the safety data sheets and the warnings on the spray can label.
Before use and before activating the hardener cartridge, shake the can for approx. 2 minutes. Shake briefly again before each further spray pass.
Dispose of empty spray cans as recyclable material.
Characteristics

Storage
The guaranteed storage stability is 36 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

2K wash primer
Designation:
- 2K Wash Primer -LLS MAX 230 M1-, color olive green (250 ml)
Product description
The 2K Wash Primer -LLS MAX 230 M1- is a zinc chromate-free and phenol-free acid-curing two-component wash primer.
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Features:
- easy processing properties
- excellent corrosion protection through passivating properties
- for metal substrates
- quick recoatability
- long pot life
- Area of application: exclusively for Clever-Repair and minor repairs
Application information
Substrate
Suitable substrates:
- Bare sheet steel, sanded
- cleaned and sanded, electrogalvanized steel panels or soft aluminum
- well-sanded original or refinish paint (except thermoplastic coating)
- surfaces pre-worked with 2K polyester products and then finely sanded
![]()
Note
Due to the variety of alloys and manufacturing processes for metals, a preliminary test on the respective substrate is required to ensure the pretreatment is sufficient for perfect adhesion.
Pretreatment of substrates:
- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

- Clean the factory or original paint and sand it, thoroughly remove any rust spots and feather the edges into the existing paint.

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

Processing
Application:
- Before activating with hardener, shake the spray can thoroughly to ensure proper curing.

- Remove the red push button from the cap and place it on the hardener mixing valve on the underside of the can.

- Press in the hardener mixing valve. When pressing in the hardener mixing valve, make sure the can is upside down.

- Shake the can thoroughly for at least 2 minutes.

Processing/pot life:
- 4 days at +20 °C

Application method "Spray pass"
- Apply 2 spray coats with a flash-off time of 5-10 minutes between coats.
Spray distance:
- Maintain a distance of 15-20 cm.
Reaction temperature:
- Minimum +15 °C
- The recommended dry film thickness is 8-12 µm.
![]()
Note
If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.

Drying
Air drying at +20 ºC room temperature:
- can be topcoated after 20-30 minutes

Overcoating
Can be overcoated with:
- 2K HS filler
![]()
Note
- This product may only be used under 2K HS filler in a three-coat system.
- Do not recoat with polyester products, epoxy products or water-reducible products.
- Do not use over thermoplastic coatings.
- Do not recoat directly with waterborne basecoat or 2K HS topcoat.
![]()
Caution!
Wear suitable personal protective equipment in accordance with occupational safety regulations.
Observe the safety data sheets and the warnings on the spray can label.
Before use and before activating the hardener cartridge, shake the can for approx. 2 minutes. Shake briefly again before each further spray pass.
Dispose of empty spray cans as recyclable material.

Personal protective equipment:
- Observe the safety data sheet
- Wear personal protective equipment during application
Characteristics


Storage
The guaranteed storage stability is 36 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 ºC.
