Engine

Engine Mechanical Tools and Preparation

3steps
~18min
2/5difficulty
Done 0 of 3

Special Service Tool

The actual shapes of TechMate tools may differ from those of special service tools illustrated here.

Tool number

(TechMate No.)

Tool name
Description

KV10116200

(NI-26336-A)

Valve spring compressor

1. KV10115900

(NI-26336-20)

Attachment

2.KV10109220

( — )

Adapter

Disassembling valve mechanism

Part is a component of KV10116200 (NI-26336-A), but Part is not so.

KV10107902

(NI-38959)

Valve oil seal puller
Replacing valve oil seal

KV10115600

(NI-38958)

Valve oil seal drift

Installing valve oil seal

Use side A .

: 20 (0.79) dia. : 8 (0.31) dia.

: 13 (0.51) dia. : 10.7 (0.421)

: 10.3 (0.406) dia. f: 5 (0.20)

: side B

Unit: mm (in)

EM03470000

(NI-8037)

Piston ring compressor
Installing piston assembly into cylinder bore

KV10111100

(NI-37228)

Seal cutter
Removing oil pan (upper), timing chain case, etc.

KV10112100

(BT-8653-A)

Angle wrench
Tightening bolts for connecting rod bearing cap, cylinder head, etc. at an angle

KV10117100

(NI-3647-A)

Heated oxygen sensor wrench

Loosening or tightening air fuel ratio sensor 1 and heated oxygen sensor

For 22 mm (0.87 in) width hexagon nut

KV10118600

(NI-48641)

Ring gear stopper
Removing and installing crankshaft pulley

KV101296S0

( — )

Direct injection puller
Removing and installing fuel injector

KV10119990

( — )

Injector seal drift set

  1. Seal installer

  2. Drift

  3. Seal guide

Installing fuel injector seal

ST10120000

(NI-24239-01)

Cylinder head bolt wrench

Loosening and tightening cylinder head bolt, and used with the angle wrench [SST: KV10112100 (BT-8653-A)]

: 13 (0.51) dia.

: 12 (0.47)

: 10 (0.39)

Unit: mm (in)

—

(NI-43897-18)

(NI-43897-12)

Oxygen sensor thread cleaner

Reconditioning the exhaust system threads before installing a new air fuel ratio sensor and heated oxygen sensor (Use with anti-seize lubricant shown below.)

A: NI-43897-18 [18 mm (0.71 in) dia.] for zirconia heated oxygen sensor and air fuel ratio sensor

B: NI-43897-12 [12 mm (0.47 in) dia.] for titania heated oxygen sensor

: Mating surface shave cylinder

: Flutes

Commercial Service Tools or/and Repair Part

Tool nameDescription
Tube presser
Pressing the tube of liquid gasket
Power tool
Loosening nuts and bolts
TORX socket
Removing and installing drive plate
Mobile floor crane
Removing and installing engine
Belt slinger
Removing and installing engine

1.Compression gauge

2.Adapter
Checking compression pressure
Spark plug wrench

Removing and installing spark plug

: 14 mm (0.55 in)
Valve seat cutter set
Finishing valve seat (EXH) dimensions
Piston ring expander
Removing and installing piston ring
Valve guide drift

Removing and installing valve guide (EXH)

Exhaust:

: 9.5 mm (0.374 in) dia.

: 5.5 mm (0.217 in) dia.
Valve guide reamer

: Reaming valve guide (EXH) inner hole

: Reaming hole for oversize valve guide (EXH)

Exhaust:

: 6.0 mm (0.236 in) dia.

: 10.2 mm (0.402 in) dia.
Anti-seize lubricant (Permatex 133AR or equivalent meeting MIL specification MIL-A-907)
Lubricating oxygen sensor thread cleaning tool when reconditioning exhaust system threads
Feeler gauge
Inspection valve clearance (Use a curved-tip gauge)

Lubricant or/and Sealant

NameDescriptionNote
Three bond 1215 Cylinder block Water drain plug
Three bond 1217H
  • Rocker cover

  • Valve timing control cover

  • Front cover

  • Oil pan (upper)

  • Camshaft

  • Cylinder block

—
Three bond 1386B Cylinder block Plug

Service Parts

NameDescription

Engine slinger

10005 6GP0B: Engine front slinger upper

10006 5CA0A: Engine rear slinger

Slinger bolts

10004 5CA0A: Engine front slinger upper/Engine rear slinger
Supporting and hoisting engine