Engine Mechanical Service Data and Specifications
Engine Assembly
GENERAL SPECIFICATIONS
| Cylinder arrangement | V-6 | ||||
| Displacement cm3 (cu in) | 3,492 (213.08) | ||||
| Bore and stroke mm (in) | 86.0 x 100.2 (3.386 x 3.944 ) | ||||
| Valve arrangement | DOHC | ||||
| Firing order | 1-2-3-4-5-6 | ||||
| Number of piston rings | Compression | 2 | |||
| Oil | 1 | ||||
| Number of main bearings | 4 | ||||
| Compression ratio | 10.5 | ||||
| Compression pressure kPa (kg/cm2, psi)/250 rpm | Standard | 1,100 - 1,400 (11.22 - 14.28, 159.5 - 203.0) | |||
| Minimum | 900 (9.18, 130.5) | ||||
| Differential limit between cylinders | 98 (1.0, 14) | ||||
Unit: degree
| Cylinder number | ![]() |
|||||
Valve timing : Intake valve |
VTC Minimum phasing (Mechanical) | VTC Maximum phasing (Mechanical) | ||||
![]() |
![]() |
|||||
a EXH valve opening angle |
b INT valve opening angle |
c INT open |
d INT close |
e EXH close |
f EXH open |
|
| VTC Minimum phasing (Mechanical) | 232 | 240 | 33 | 93 | -3 | 55 |
| VTC Maximum phasing (Mechanical) | 40 | 20 | 64 | -12 | ||
Drive Belt
DRIVE BELT
| Tension of drive belt | Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner. |
Spark Plug
SPARK PLUG
Unit: mm (in)
| Make | NGK |
| Standard type | ILKAR8AB8G |
| Gap (Nominal) | 0.8 (0.031) |
Intake Manifold
INTAKE MANIFOLD
Unit: mm (in)
| Items | Limit | |
|---|---|---|
| Surface distortion | Intake manifold | 1.0 (0.039) |
Turbocharger
TURBOCHARGER
Unit: mm (in)
| Items | Limit | |
|---|---|---|
| Surface distortion | Turbocharger | 0.1 (0.004) |
Camshaft
CAMSHAFT
Unit: mm (in)
| Items | Standard | Limit | ||||
|---|---|---|---|---|---|---|
| Camshaft journal oil clearance | No. 1 | 0.045 - 0.086 (0.0018 - 0.0034) | 0.150 (0.0059) | |||
| No. 2, 3, 4 | 0.035 - 0.076 (0.0014 - 0.0030) | |||||
| Camshaft bracket inner diameter | No. 1 | 26.000 - 26.021 (1.0236 - 1.0244) | — | |||
| No. 2, 3, 4 | 23.500 - 23.521 (0.9252 - 0.9260) | — | ||||
| Camshaft journal diameter | No. 1 | 25.935 - 25.955 (1.0211 - 1.0218) | — | |||
| No. 2, 3, 4 | 23.445 - 23.465 (0.9230 - 0.9238) | — | ||||
| Camshaft end play | 0.115 - 0.188 (0.0045 - 0.0074) | 0.24 (0.0094) | ||||
| Camshaft cam height “A” | Intake | 45.265 - 45.455 (1.7821 - 1.7896) | 0.2 (0.008)*1 | |||
| Exhaust | 43.675 - 43.865 (1.7195 - 1.7269) | |||||
| Pump | 57.0 - 57.4 (2.244 - 2.260) | |||||
| Camshaft runout [TIR*2] | Less than 0.02 (0.0008) | 0.05 (0.0020) | ||||
| Camshaft sprocket runout [TIR*2] | — | 0.15 (0.0059) | ||||
![]() |
||||||
*1: Cam wear limit
*2: Total indicator reading
VALVE LIFTER
Unit: mm (in)
| Items | Standard | |
|---|---|---|
| Valve lifter outer diameter | Intake | 33.980 - 33.990 (1.3378 - 1.3382) |
| Exhaust | 29.977 - 29.987 (1.1802 - 1.1806) | |
| Valve lifter hole diameter | Intake | 34.000 - 34.016 (1.3386 - 1.3392) |
| Exhaust | 29.997 - 30.013 (1.1810 - 1.1816) | |
| Valve lifter clearance | 0.010 - 0.036 (0.0004 - 0.0014) | |
VALVE CLEARANCE
Unit: mm (in)
| Items | Cold | Hot* (reference data) |
|---|---|---|
| Intake | 0.26 - 0.34 (0.0103 - 0.0133) | 0.304 - 0.416 (0.0120 - 0.0163) |
| Exhaust | 0.28 - 0.36 (0.0111 - 0.0141) | 0.308 - 0.432 (0.0122 - 0.0170) |
*: Approximately 80 °C
AVAILABLE VALVE LIFTER
Unit: mm (in)
| Identification mark | Thickness | |
|---|---|---|
| Intake | Exhaust | Thickness |
| 300+ | 300- | 3.00 (0.1181) |
| 302+ | 302- | 3.02 (0.1189) |
| 304+ | 304- | 3.04 (0.1197) |
| 306+ | 306- | 3.06 (0.1205) |
| 308+ | 308- | 3.08 (0.1213) |
| 310+ | 310- | 3.10 (0.1220) |
| 312+ | 312- | 3.12 (0.1228) |
| 314+ | 314- | 3.14 (0.1236) |
| 316+ | 316- | 3.16 (0.1244) |
| 318+ | 318- | 3.18 (0.1252) |
| 320+ | 320- | 3.20 (0.1260) |
| 322+ | 322- | 3.22 (0.1268) |
| 324+ | 324- | 3.24 (0.1276) |
| 326+ | 326- | 3.26 (0.1283) |
| 328+ | 328- | 3.28 (0.1291) |
| 330+ | 330- | 3.30 (0.1299) |
| 332+ | 332- | 3.32 (0.1307) |
| 334+ | 334- | 3.34 (0.1315) |
| 336+ | 336- | 3.36 (0.1323) |
| 338+ | 338- | 3.38 (0.1331) |
| 340+ | 340- | 3.40 (0.1339) |
| 342+ | 342- | 3.42 (0.1346) |
| 344+ | 344- | 3.44 (0.1354) |
| 346+ | 346- | 3.46 (0.1362) |
| 348+ | 348- | 3.48 (0.1370) |
| 350+ | 350- | 3.50 (0.1378) |
![]() |
||
CylinderHead
CYLINDER HEAD
Unit: mm (in)
| Items | Standard | Limit |
|---|---|---|
| Head surface distortion | Less than 0.03 (0.0012) | 0.1 (0.004) |
| Normal cylinder head height “H” | 126.4 (4.98) | — |
![]() |
||
VALVE DIMENSIONS
Unit: mm (in)
![]() |
|||
| Valve head diameter “D” | Intake | 33.2 - 33.5 (1.307 - 1.319) | |
| Exhaust | 28.32 - 28.62 (1.1150 - 1.1267) | ||
| Valve length “L” | Intake | 101.05 (3.9783) | |
| Exhaust | 97.48 (3.8378) | ||
| Valve stem diameter “d” | Intake | 5.465 - 5.480 (0.2152 - 0.2157) | |
| Exhaust | 5.455 - 5.470 (0.2148 - 0.2154) | ||
| Valve seat angle “α” | Intake | 45°15′ - 45°45′ | |
| Exhaust | |||
| Valve margin “T” | Intake | 1.1 (0.043) | |
| Exhaust | 1.3 (0.051) | ||
| Valve margin “T” limit | 0.5 (0.020) | ||
| Valve stem end surface grinding limit | 0.2 (0.008) | ||
VALVE GUIDE
Unit: mm (in)
![]() | |||
|---|---|---|---|
| Items | Standard | Oversize (Service) [0.2 (0.008)] | |
| Valve guide | Outer diameter | 9.523 - 9.534 (0.3749 - 0.3754) | 9.723 - 9.734 (0.3828 - 0.3832) |
| Inner diameter (Finished size) | 5.500 - 5.518 (0.2165 - 0.2172) | ||
| Cylinder head valve guide hole diameter | 9.475 - 9.496 (0.3730 - 0.3739) | 9.675 - 9.696 (0.3809 - 0.3817) | |
| Interference fit of valve guide | 0.027 - 0.059 (0.0011 - 0.0023) | ||
Unit: mm (in)
| Items | Standard | Limit | |
|---|---|---|---|
| Valve guide clearance | Intake | 0.020 - 0.053 (0.0008 - 0.0021) | 0.08 (0.0031) |
| Exhaust | 0.030 - 0.063 (0.0012 - 0.0025) | 0.09 (0.0035) | |
| Projection length “L” | 12.6 - 12.8 (0.496 - 0.504) | ||
VALVE SEAT
Unit: mm (in)
![]() | |||
|---|---|---|---|
| Items | Standard | Oversize (Service) [0.5 (0.02)] | |
| Cylinder head seat recess diameter “D” | Intake | 34.100 - 34.116 (1.3425 - 1.3431) | 34.600 - 34.616 (1.3622 - 1.3628) |
| Exhaust | 28.600 - 28.616 (1.1260 - 1.1266) | 29.100 - 29.116 (1.1457 - 1.1463) | |
| Valve seat outer diameter “d” | Intake | 34.197 - 34.213 (1.3463 - 1.3470) | 34.697 - 34.713 (1.3660 - 1.3667) |
| Exhaust | 28.680 - 28.696 (1.1291 - 1.1298) | 29.180 - 29.196 (1.1488 - 1.1494) | |
| Valve seat interference fit | Intake | 0.081 - 0.113 (0.0032 - 0.0044) | |
| Exhaust | 0.064 - 0.096 (0.0025 - 0.0038) | ||
| Diameter “d1”*1 | Intake | 31.2 (1.228) | |
| Exhaust | 25.8 (1.016) | ||
| Diameter “d2”*2 | Intake | 32.5 - 33.0 (1.280 - 1.299) | |
| Exhaust | 27.4 - 27.9 (1.079 - 1.098) | ||
| Angle “α1” | Intake | 70° | |
| Exhaust | 60° | ||
| Angle “α2” | Intake | 88°45′ - 90°15′ | |
| Exhaust | 88°45′ - 90°15′ | ||
| Angle “α3” | Intake | 120° | |
| Exhaust | 120° | ||
| Contacting width “W”*3 | Intake | 1.0 - 1.4 (0.039 - 0.055) | |
| Exhaust | 1.2 - 1.6 (0.047 - 0.063) | ||
| Height “h” | Intake | 4.7 (0.185) | 4.9 (0.193) |
| Exhaust | 5.2 (0.205) | 5.4 (0.213) | |
| Depth “H” | Intake | 5.3 (0.209) | |
| Exhaust | 6.0 (0.236) | ||
*1: Diameter made by intersection point of conic angles “α1” and “α2”
*2: Diameter made by intersection point of conic angles “α2” and “α3”
*3: Machining data
VALVE SPRING
| Items | Standard | ||
|---|---|---|---|
| Intake | Exhaust | ||
| Free height | 48.51 mm (1.9098 in) | 61.76 mm (2.4315 in) | |
| Pressure | Installation | 166 - 188 N (16.94 - 19.17 kg, 37.31 - 42.26 lb) | 315 - 355 N (32.13 - 36.21 kg, 70.82 - 79.80 lb) |
| Valve open | 384 - 432 N (39.17 - 44.06 kg, 86.32 - 97.11 lb) | 473 - 533 N (48.25 - 54.36 kg, 106.33 - 119.81 lb) | |
| Identification color | White | Yellow | |
| Items | Limit | ||
|---|---|---|---|
| Intake | Exhaust | ||
| Out-of-square | 1.7 mm (0.067 in) | 2.2 mm (0.087 in) | |
CylinderBlock
CYLINDER BLOCK
Unit: mm (in)
![]() |
||||
| Surface flatness | Standard | Less than 0.03 (0.0012) | ||
| Limit | 0.1 (0.004) | |||
| Main bearing housing inner diameter | Standard | 69.993 - 70.017 (2.7556 - 2.7566) | ||
| Cylinder bore | Inner diameter | Standard | 86.000 - 86.015 (3.3858 - 3.3864) | |
| Wear limit | 0.2 (0.008) | |||
| Out-of-round | Limit | 0.015 (0.0006) | ||
| Taper | 0.010 (0.0004) | |||
| Main bearing housing inner diameter grade (Without bearing) | Grade No. A Grade No. B Grade No. C Grade No. D Grade No. E Grade No. F Grade No. G Grade No. H Grade No. J Grade No. K Grade No. L Grade No. M Grade No. N Grade No. P Grade No. R Grade No. S Grade No. T Grade No. U Grade No. V Grade No. W Grade No. X Grade No. Y Grade No. 4 |
79.993 - 79.994 (3.1493 - 3.1494) 79.994 - 79.995 (3.1494 - 3.1494) 79.995 - 79.996 (3.1494 - 3.1494) 79.996 - 79.997 (3.1494 - 3.1495) 79.997 - 79.998 (3.1495 - 3.1495) 79.998 - 79.999 (3.1495 - 3.1496) 79.999 - 80.000 (3.1496 - 3.1496) 80.000 - 80.001 (3.1496 - 3.1496) 80.001 - 80.002 (3.1496 - 3.1497) 80.002 - 80.003 (3.1497 - 3.1497) 80.003 - 80.004 (3.1497 - 3.1498) 80.004 - 80.005 (3.1498 - 3.1498) 80.005 - 80.006 (3.1498 - 3.1498) 80.006 - 80.007 (3.1498 - 3.1499) 80.007 - 80.008 (3.1499 - 3.1499) 80.008 - 80.009 (3.1499 - 3.1500) 80.009 - 80.010 (3.1500 - 3.1500) 80.010 - 80.011 (3.1500 - 3.1500) 80.011 - 80.012 (3.1500 - 3.1501) 80.012 - 80.013 (3.1501 - 3.1501) 80.013 - 80.014 (3.1501 - 3.1502) 80.014 - 80.015 (3.1502 - 3.1502) 80.015 - 80.016 (3.1502 - 3.1502) |
||
| Difference in inner diameter between cylinders | Standard | Less than 0.03 (0.0012) | ||
AVAILABLE PISTON
Unit: mm (in)
![]() | |||
|---|---|---|---|
| Items | Standard | ||
| Piston skirt diameter “A” | 85.965 - 85.980 (3.3844 - 3.3850) | ||
| Items | Standard | Limit |
|---|---|---|
| “a” dimension | 39.00 (1.5354) | — |
| Piston pin hole diameter | 22.995 - 22.999 (0.9053 - 0.9055) | — |
| Piston to cylinder bore clearance | 0.020 - 0.050 (0.0008 - 0.0020) | 0.09 (0.0035) |
PISTON RING
Unit: mm (in)
| Items | Standard | Limit | |
|---|---|---|---|
| Side clearance | Top | 0.040 - 0.080 (0.0016 - 0.0031) | 0.11 (0.0043) |
| 2nd | 0.030 - 0.070 (0.0012 - 0.0028) | 0.10 (0.0039) | |
| Oil ring | 0.055 - 0.155 (0.0022 - 0.0061) | — | |
| End gap | Top | 0.23 - 0.28 (0.0091 - 0.0110) | 0.45 (0.0177) |
| 2nd | 0.38 - 0.48 (0.0150 - 0.0189) | 0.62 (0.0244) | |
| Oil (rail ring) | 0.17 - 0.42 (0.0067 - 0.0165) | 0.72 (0.0283) | |
PISTON PIN
Unit: mm (in)
| Items | Standard | Limit | |
|---|---|---|---|
| Piston pin outer diameter | 22.989 - 22.993 (0.9051 - 0.9052) | — | |
| Piston to piston pin oil clearance | 0.002 - 0.010 (0.0001 - 0.0004) | — | |
| Connecting rod bushing oil clearance | 0.007 - 0.017 (0.0003 - 0.0007) | 0.030 (0.0012) | |
CONNECTING ROD
Unit: mm (in)
| Items | Standard | Limit | |
|---|---|---|---|
| Center distance | 164.23 - 164.37 (6.47 - 6.47) | — | |
| Bend [per 100 (3.94)] | — | 0.15 (0.0059) | |
| Torsion [per 100 (3.94)] | — | 0.30 (0.0118) | |
| Connecting rod bushing inner diameter* | 23.000 - 23.006 (0.9055 - 0.9057) | — | |
| Connecting rod big end diameter (Without bearing) | Grade No. A | 59.000 - 59.001 (2.3228 - 2.3229) | — |
| Grade No. B | 59.001 - 59.002 (2.3229 - 2.3229) | — | |
| Grade No. C | 59.002 - 59.003 (2.3229 - 2.3229) | — | |
| Grade No. D | 59.003 - 59.004 (2.3229 - 2.3230) | — | |
| Grade No. E | 59.004 - 59.005 (2.3230 - 2.3230) | — | |
| Grade No. F | 59.005 - 59.006 (2.3230 - 2.3231) | — | |
| Grade No. G | 59.006 - 59.007 (2.3231 - 2.3231) | — | |
| Grade No. H | 59.007 - 59.008 (2.3231 - 2.3231) | — | |
| Grade No. J | 59.008 - 59.009 (2.3231 - 2.3232) | — | |
| Grade No. K | 59.009 - 59.010 (2.3232 - 2.3232) | — | |
| Grade No. L | 59.010 - 59.011 (2.3232 - 2.3233) | — | |
| Grade No. M | 59.011 - 59.012 (2.3233 - 2.3233) | — | |
| Grade No. N | 59.012 - 59.013 (2.3233 - 2.3233) | — | |
| Side clearance | 0.20 - 0.35 (0.0079 - 0.0138) | 0.35 (0.0138) | |
*: After installing in connecting rod
CRANKSHAFT
Unit: mm (in)
![]() |
![]() |
||
| Main journal diameter. “Dm” grade | Standard | Grade No. A Grade No. B Grade No. C Grade No. D Grade No. E Grade No. F Grade No. G Grade No. H Grade No. J Grade No. K Grade No. L Grade No. M Grade No. N Grade No. P Grade No. R Grade No. S Grade No. T Grade No. U Grade No. V Grade No. W Grade No. X Grade No. Y Grade No. 4 Grade No. 7 |
74.975 - 74.974 (2.9518 - 2.9517) 74.974 - 74.973 (2.9517 - 2.9517) 74.973 - 74.972 (2.9517 - 2.9516) 74.972 - 74.971 (2.9516 - 2.9516) 74.971 - 74.970 (2.9516 - 2.9516) 74.970 - 74.969 (2.9516 - 2.9515) 74.969 - 74.968 (2.9515 - 2.9515) 74.968 - 74.967 (2.9515 - 2.9515) 74.967 - 74.966 (2.9515 - 2.9514) 74.966 - 74.965 (2.9514 - 2.9514) 74.965 - 74.964 (2.9514 - 2.9513) 74.964 - 74.963 (2.9513 - 2.9513) 74.963 - 74.962 (2.9513 - 2.9513) 74.962 - 74.961 (2.9513 - 2.9512) 74.961 - 74.960 (2.9512 - 2.9512) 74.960 - 74.959 (2.9512 - 2.9511) 74.959 - 74.958 (2.9511 - 2.9511) 74.958 - 74.957 (2.9511 - 2.9511) 74.957 - 74.956 (2.9511 - 2.9510) 74.956 - 74.955 (2.9510 - 2.9510) 74.955 - 74.954 (2.9510 - 2.9509) 74.954 - 74.953 (2.9509 - 2.9509) 74.953 - 74.952 (2.9509 - 2.9509) 74.952 - 74.951 (2.9509 - 2.9508) |
| Pin journal diameter. “Dp” grade | Standard | Grade No. A | 55.974 - 55.973 (2.2037 - 2.2037) |
| Grade No. B | 55.973 - 55.972 (2.2037 - 2.2036) | ||
| Grade No. C | 55.972 - 55.971 (2.2036 - 2.2036) | ||
| Grade No. D | 55.971 - 55.970 (2.2036 - 2.2035) | ||
| Grade No. E | 55.970 - 55.969 (2.2035 - 2.2035) | ||
| Grade No. F | 55.969 - 55.968 (2.2035 - 2.2035) | ||
| Grade No. G | 55.968 - 55.967 (2.2035 - 2.2034) | ||
| Grade No. H | 55.967 - 55.966 (2.2034 - 2.2034) | ||
| Grade No. J | 55.966 - 55.965 (2.2034 - 2.2033) | ||
| Grade No. K | 55.965 - 55.964 (2.2033 - 2.2033) | ||
| Grade No. L | 55.964 - 55.963 (2.2033 - 2.2033) | ||
| Grade No. M | 55.963 - 55.962 (2.2033 - 2.2032) | ||
| Grade No. N | 55.962 - 55.961 (2.2032 - 2.2032) | ||
| Grade No. P | 55.961 - 55.960 (2.2032 - 2.2031) | ||
| Grade No. R | 55.960 - 55.959 (2.2031 - 2.2031) | ||
| Grade No. S | 55.959 - 55.958 (2.2031 - 2.2031) | ||
| Grade No. T | 55.958 - 55.957 (2.2031 - 2.2030) | ||
| Grade No. U | 55.957 - 55.956 (2.2030 - 2.2030) | ||
| Center distance “r” | 50.06 - 50.14 (1.9709 - 1.9740) | ||
| Taper (Difference between “A” and “B”) | Limit | 0.001 (0.0000393) | |
| Out-of-round (Difference between “X” and “Y”) | 0.0025 (0.0001) | ||
| Crankshaft runout [TIR*] | Standard | Less than 0.05 (0.0020) | |
| Limit | 0.05 (0.0020) | ||
| Crankshaft end play | Standard | 0.20 - 0.35 (0.0079 - 0.0138) | |
| Limit | 0.35 (0.0138) | ||
*: Total indicator reading
Connecting Rod Bearing
CONNECTING ROD BEARING
Unit: mm (in)
| Grade number | Thickness | Identification color (mark) | |
|---|---|---|---|
| 0 | UPR | 1.497 - 1.500 (0.0589 - 0.0591) | Black |
| LWR | Black - Black | ||
| 1 | UPR | 1.500 - 1.503 (0.0591 - 0.0592) | Brown |
| LWR | Brown - Brown | ||
| 2 | UPR | 1.503 - 1.506 (0.0592 - 0.0593) | Green |
| LWR | Green - Green | ||
| 3 | UPR | 1.506 - 1.509 (0.0593 - 0.0594) | Yellow |
| LWR | Yellow - Yellow | ||
| 4 | UPR | 1.509 - 1.512 (0.0594 - 0.0595) | Blue |
| LWR | Blue - Blue |
UNDERSIZE
Unit: mm (in)
| Items | Thickness | Crank pin journal diameter |
|---|---|---|
| 0.25 (0.0098) | 1.626 - 1.634 (0.0640 - 0.0643) | Grind so that bearing clearance is the specified value. |
CONNECTING ROD BEARING OIL CLEARANCE
Unit: mm (in)
| Items | Standard | Limit |
|---|---|---|
| Connecting rod bearing oil clearance | 0.026 - 0.039 (0.0010 - 0.0015)* | 0.051 (0.0020) |
*: Actual clearance
Main Bearing
MAIN BEARING
Unit: mm (in)
![]() | |||||
|---|---|---|---|---|---|
| Grade number | Thickness | Width | Identification color | Remarks | |
| 0 | 2.500 - 2.503 (0.0984 - 0.0985) | 19.9 - 20.1 (0.783 - 0.791) |
Black - Black | Grade is the same for upper and lower bearings. | |
| 1 | 2.503 - 2.506 (0.0985 - 0.0987) | Brown - Brown | |||
| 2 | 2.506 - 2.509 (0.0987 - 0.0988) | Green - Green | |||
| 3 | 2.509 - 2.512 (0.0988 - 0.0989) | Yellow - Yellow | |||
| 4 | 2.512 - 2.515 (0.0989 - 0.0990) | Blue - Blue | |||
| 5 | 2.515 - 2.518 (0.0990 - 0.0991) | Pink - Pink | |||
| 6 | 2.518 - 2.521 (0.0991 - 0.0993) | Purple - Purple | |||
| 7 | 2.521 - 2.524 (0.0993 - 0.0994) | White - White | |||
| 01 | UPR | 2.503 - 2.506 (0.0985 - 0.0987) | Brown - Brown | Grade and color are different for upper and lower bearings. | |
| LWR | 2.500 - 2.503 (0.0984 - 0.0985) | Black - Black | |||
| 12 | UPR | 2.506 - 2.509 (0.0987 - 0.0988) | Green - Green | ||
| LWR | 2.503 - 2.506 (0.0985 - 0.0987) | Brown - Brown | |||
| 23 | UPR | 2.509 - 2.512 (0.0988 - 0.0989) | Yellow - Yellow | ||
| LWR | 2.506 - 2.509 (0.0987 - 0.0988) | Green - Green | |||
| 34 | UPR | 2.512 - 2.515 (0.0989 - 0.0990) | Blue - Blue | ||
| LWR | 2.509 - 2.512 (0.0988 - 0.0989) | Yellow - Yellow | |||
| 45 | UPR | 2.515 - 2.518 (0.0990 - 0.0991) | Pink - Pink | ||
| LWR | 2.512 - 2.515 (0.0989 - 0.0990) | Blue - Blue | |||
| 56 | UPR | 2.518 - 2.521 (0.0991 - 0.0993) | Purple - Purple | ||
| LWR | 2.515 - 2.518 (0.0990 - 0.0991) | Pink - Pink | |||
| 67 | UPR | 2.521 - 2.524 (0.0993 - 0.0994) | White - White | ||
| LWR | 2.518 - 2.521 (0.0991 - 0.0993) | Purple - Purple | |||
UNDERSIZE
Unit: mm (in)
| Items | Thickness | Main journal diameter |
|---|---|---|
| 0.25 (0.0098) | 2.633 - 2.641 (0.1037 - 0.1040) | Grind so that bearing clearance is the specified value. |
MAIN BEARING OIL CLEARANCE
Unit: mm (in)
| Items | Standard | Limit |
|---|---|---|
| Main bearing oil clearance | 0.012 - 0.022 (0.0005 - 0.0009) | 0.022 (0.0009) |
*: Actual clearance













