Engine

Turbocharger

~10min read
02040608010034.525N·mlb·ft
Tightening torque found on this page

Exploded View

Bank 1 side

Water inlet hose Clamp Water inlet tube
O-ring Heat insulator (upper) Oil return pipe 1
Oil return hose Oil return pipe 2 Heat insulator (lower)
Water outlet tube Turbocharger assembly Gasket 1
Stud bolt Oil feed tube Eye bolt
Gasket 2
Comply with the installation procedure when tightening. Refer to Removal & Installation. To air duct. Refer to Exploded View. To catalyst converter (bank 2). Refer to Exploded View.
To lower cylinder block.Refer to Exploded View. To cylinder head (bank 1). Refer to Exploded View. To air inlet tube 1. Refer to Exploded View.
To oil inlet adapter. Refer to Bank 2 side. To cylinder head (bank 1). Refer to Exploded View. To water pipe assembly. Refer to Exploded View.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.

Bank 2 side

Heat insulator (lower) Clamp Water inlet tube
O-ring Oil return pipe 2 Oil return hose
Oil return pipe 1 Water outlet hose Water outlet tube
Heat insulator (upper) Eye bolt Gasket 1
Oil feed tube Oil inlet adapter Gasket 3
Turbocharger assembly Gasket 2 Stud bolt
Comply with the installation procedure when tightening. Refer to Removal & Installation . To air duct. Refer to Exploded View. To catalyst converter (bank 2). Refer to Exploded View.
To lower cylinder block. Refer to Exploded View. To water pipe 2 assembly. Refer to Exploded View. To air inlet tube 1. Refer to Exploded View.
To cylinder block. Refer to Exploded View. To cylinder head (bank 2). Refer to Exploded View. To electric throttle control actuator. Refer to Exploded View.
To oil feed tube. Refer to Bank 1 side.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the parts is connected at points with same symbols in actual vehicle.

Removal & Installation

REMOVAL

Disconnect battery cables from negative terminal. Refer to Exploded View.

Drain engine coolant. Refer to ENGINE COOLANT : Draining.

Remove the following parts:

  • Drive belt. Refer to Removal & Installation

  • Air cleaner and air duct assembly. Refer to Removal and Installation.

  • Inlet air duct 2. Refer to Removal and Installation.

  • Air inlet tube 1 and 2. Refer to Removal & Installation.

  • Intake manifold. Refer to Removal and Installation

  • Main muffler. Refer to EXHAUST SYSTEM : Removal & Installation.

Bank 1 side

Remove front tire assembly (RH). Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove fender protector (RH). Refer to Removal and Installation.

Remove 2nd catalyst converter (bank 1). Refer to Removal and Installation.

Remove heat insulator (upper) .

: Engine front

Remove catalyst converter (bank 1). Refer to Removal and Installation.

Remove starter motor. Refer to Removal and Installation.

Remove alternator. Refer to Removal and Installation.

Remove oil return pipe 1 from the turbocharger assembly side.

: Engine front

Remove air duct 3. Refer to Removal and Installation.

Remove water hose 1. Refer to Removal and Installation

Remove mounting bolt of water outlet tube .

: Engine upper

Remove water inlet tube .

: Engine front

Remove mounting bolt of oil feed tube .

: Engine upper

Remove each hose connected to water pipe 1. Refer to Removal and Installation.

Remove water pipe 1. Refer to Removal and Installation.

Remove front heater pipe assembly. Refer to Exploded View.

Remove oil feed tube from the oil inlet adapter side.

Disconnect turbocharger speed sensor harness connector.

Loosen turbocharger assembly mounting nuts in the order from 4 to 1 as shown in the figure.

Move the turbocharger assembly to the rear of the engine. Remove turbocharger assembly from the top of the engine by rotating it vertically in the following order.

Remove gasket 1.

Bank 2 side

Remove front tire assembly (LH). Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove fender protector (LH). Refer to Removal and Installation.

Release fuel pressure. Refer to Work Procedure.

Discharge refrigerant from A/C circuit. Refer to Recycle Refrigerant.

Remove 2nd catalyst converter. Refer to Removal and Installation.

Remove heat insulator (upper) .

: Engine upper

Remove catalyst converter (bank 2). Refer to Removal and Installation.

Remove A/C compressor belt. Refer to Removal & Installation.

Remove EVAP canister purge volume control solenoid valve and the connected hose as a set. Refer to Exploded View.

Remove fuel feed hose. Refer to Removal & Installation.

Remove ground cable. Refer to Exploded View.

Remove each hose connected to water pipe 2. Refer to Removal and Installation.

Remove water pipe 2. Refer to Removal and Installation.

Remove high pressure flexible hose and low pressure flexible hose. Refer to Exploded View.

Remove A/C compressor. Refer to Removal and Installation.

Remove air duct 3. Refer to Removal and Installation.

Remove oil level gauge and oil level gauge guide. Refer to Exploded View.

Disconnect the sub harness connector. Refer to Exploded View.

Remove oil feed tube from the inlet adapter side.

Remove mounting bolt of oil feed tube .

: Engine upper

Disconnect turbocharger speed sensor harness connector.

Loosen turbocharger assembly mounting nuts in the order from 4 to 1 as shown in the figure.

Remove turbocharger assembly.

Remove gasket 2.

Oil feed tube

Fix the turbocharger in a vise (A).

Remove oil feed tube mounting bolts from the turbocharger .

INSTALLATION

Turbocharger side

Install in the reverse order of removal.

Install turbocharger assembly in the reverse order of removal and in the order shown in the figure. (Bank 1 side).

Install turbocharger assembly in the order from 1 to 4 as shown in the figure.

: 34 N·m

Install oil return pipe.

Install water tube according to the following procedure.

: Bank 1
: Bank 2
: Engine front
Temporarily tighten water tube bolt . Temporarily tighten bracket bolt . Tighten water tube bolt to the torque specified below.
: 9 N·m
Tighten bracket bolt to the torque specified below.
: 9 N·m

Install water hose.

  • Align with paint mark (Yellow).

Install the oil feed tube with the following procedure.

: Bank 1
: Bank 2
: Engine front
  • Temporarily tighten eye bolt.

  • Tighten eye bolt to the torque specified below.

    : 17 N·m

Oil inlet adapter

Install oil inlet adapter.

Temporarily tighten eye bolt .

Temporarily tighten mounting bolt of oil feed tube . (Bank 1 side)

: vehicle front

Temporarily tighten mounting bolt of oil feed tube . (Bank 2 side)

: vehicle front

Tighten to the specified torque eye bolt .

: 25 N·m

Tighten to the specified torque mounting bolt of oil feed tube . (Bank 1 side).

: vehicle front
: 9 N·m

Tighten to the specified torque mounting bolt of oil feed tube . (Bank 2 side).

: vehicle front
: 9 N·m

Inspection

INSPECTION PROCERDURE

Trouble Diagnosis of Turbocharger

Check items before trouble diagnosis

Check that the engine oil level is between L (Low level) and H (High level) of the oil level gauge. [When the engine oil amount is more then H (High level), the engine oil flows into the inlet duct through the blow-by gas passage, and the turbocharger is misjudged failure.]

Ask the customer if he/she always runs the vehicle in idle engine speed to cool the engine oil down after driving.

  • Replace the turbocharger assembly when any malfunction is found after unit inspections specified in the table below.

  • If no malfunction is found after the unit inspections, judge that the turbocharger body has no non-standard conditions. Check the other parts again.

    Inspection LocationResultSymptoms likely to occur when the results shown on the left exist.
    Oil leakageSmokeNoise*

    Poor power

    Poor acceleration
    Turbine wheel Wet with oil. C A C C
    Carbon deposits observed. C A B B
    “Rubs against” housing. C B A B
    Vane is bent or broken. A A
    Compressor wheel Inside of intake port is badly stained with oil. B B
    “Rubs against” housing. C B A B
    Vane is bent or broken. A A
    Check both turbine and compressor rotor shaft end play. Heavy feel or catching when turned by hand. C C B
    Cannot be turned by hand. A
    Excessively loose bearing. C C B C
    Rotor shaft, oil return port (Check inside using penlight.) Carbon or sludge deposits in oil drain port. B A C C
    Boost control valve actuator operation (using a handy pump)
    • Does not operate smoothly when air pressure is gradually applied.

    • Stroke amount is not compliance with the air pressure.

    A
    A: Highly possible. B: Possible. C: May exist.

    * Racing under cold engine may generate a noise from the area of wastegate valve. This is not a turbocharger malfunction. The noise stops after engine warm-up.

INSPECTION AFTER REMOVAL

Bank1 side

Location to check for air leaks Location to check for engine oil leaks Location to check for engine coolant leaks
Location to check for exhaust gas leaks

Bank2 side

Location to check for air leaks Location to check for engine oil leaks Location to check for engine coolant leaks
Location to check for exhaust gas leaks
Intake side : Between turbocharger and charge air cooler
Exhaust side : Between turbocharger and outlet duct

INSPECTION AFTER INSTALLATION

Start engine and raise engine speed to check no exhaust emission leaks.