Deceleration Sensor Internal Circuit (C1419,C1435). Malfunction in Deceleration Sensor (C1420). Open in Stop Light Switch Circuit (C1425)
Deceleration Sensor Internal Circuit (C1419,C1435)
DESCRIPTION
These DTCs are stored when the skid control ECU (brake actuator assembly) receives an internal malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1419 |
Deceleration Sensor Internal Circuit |
With the +BS terminal voltage between 9.6 and 16.5 V, an acceleration sensor malfunction signal is received from the acceleration sensor. |
Acceleration sensor (airbag sensor assembly) |
C1435 |
Yaw Rate Sensor Internal Circuit |
With the +BS terminal voltage between 9.6 and 16.5 V, a yaw rate sensor malfunction signal is received from the yaw rate sensor. |
Yaw rate sensor (airbag sensor assembly) |
NOTICE:
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here ![]()
PROCEDURE
REPLACE AIRBAG SENSOR ASSEMBLY
(a) Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click here ![]()
| NEXT | END |
Malfunction in Deceleration Sensor (C1420)
DESCRIPTION
This DTC is stored when the skid control ECU (brake actuator assembly) detects an abnormality in the difference between the acceleration sensor value and the control value estimated based on the yaw rate sensor, steering angle sensor and speed sensor signals.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1420 |
Malfunction in Deceleration Sensor |
The difference between the acceleration sensor value and the control value estimated inside the skid control ECU (brake actuator assembly) is abnormal. |
|
NOTICE:
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here ![]()
PROCEDURE
CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
(a) Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click here ![]()
OK:
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| OK | REPLACE AIRBAG SENSOR ASSEMBLY |
| NG | INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY |
Open in Stop Light Switch Circuit (C1425)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.
The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.
If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1425 |
Open in Stop Light Switch Circuit |
An open in the stop light switch assembly input line continues for 3 seconds or more. |
|
WIRING DIAGRAM
Ref to DTC C1249.
Click here ![]()
NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
READ VALUE USING TECHSTREAM (BS1 VOLTAGE VALUE)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.
Chassis > ABS/VSC/TRAC/EPB > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
BS1 Voltage Value |
+BS voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- |
Changes in proportion to battery voltage |
BS1 Voltage Value
(d) Take a note of the +BS voltage value.
HINT:
The noted +BS voltage value is used in a later step.
|
INSPECT STOP LIGHT SWITCH ASSEMBLY
(a) Inspect the stop light switch assembly.
Click here ![]()
OK:
The stop light switch assembly is normal.
| NG | REPLACE STOP LIGHT SWITCH ASSEMBLY |
|
READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.
Chassis > ABS/VSC/TRAC/EPB > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Stop Light SW |
Stop light switch assembly |
ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
Stop Light SW
(d) Check that the stop light switch assembly display observed on the Techstream changes according to brake pedal operation.
OK:
The Techstream displays on or off according to brake pedal operation.
| NG | GO TO STEP 5 |
|
RECONFIRM DTC
(a) Clear the DTCs.
Chassis > ABS/VSC/TRAC/EPB > Clear DTCs(b) Turn the engine switch off.
(c) Start the engine.
(d) Depress the brake pedal several times to test the stop light circuit.
(e) Check if the same DTC is output.
Chassis > ABS/VSC/TRAC/EPB > Trouble CodesResult | Proceed to |
|---|---|
C1425 is not output |
A |
C1425 is output |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE ACTUATOR ASSEMBLY |
CHECK HARNESS AND CONNECTOR (STP TERMINAL)
(a) Turn the engine switch off. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the A28 skid control ECU (brake actuator assembly) connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A28-42 (STP) - Body ground |
Stop light switch assembly on (Brake pedal depressed) |
(+BS x 0.85) to 14 V* |
A28-42 (STP) - Body ground |
Stop light switch assembly off (Brake pedal released) |
Below 1.5 V |
HINT:
*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.
| OK | REPLACE BRAKE ACTUATOR ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT) |
