Brake Pedal(for Hv Model)
Adjustment
ADJUSTMENT
PROCEDURE
1. INSPECT AND ADJUST BRAKE PEDAL HEIGHT
(a) Remove the front door scuff plate LH.
Click here ![]()
(b) Remove the cowl side trim sub-assembly LH.
Click here ![]()
(c) Remove the No. 1 instrument panel under cover sub-assembly.
Click here ![]()
(d) Remove the accelerator pedal pad.
Click here ![]()
(e) Remove the accelerator pedal.
Click here ![]()
(f) Check the brake pedal height.
HINT:
Inspect and adjust the brake pedal height with the floor carpet and front floor mat folded back.
(1) Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.
*1 |
Brake Pedal Pad |
- |
- |
*a |
Brake Pedal Height |
*b |
Measuring Plane of Floor Panel |
*c |
36 mm (1.42 in.) |
- |
- |
Brake Pedal Height from Floor Panel:
147.5 to 161.5 mm (5.81 to 6.36 in.)
HINT:
If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.
(g) Adjust the push rod length.
(1) Remove the stop light switch assembly. Click here |
|
(2) Loosen the lock nut.
(3) Adjust the brake pedal height by turning the push rod.
Brake Pedal Height from Floor Panel:
147.5 to 161.5 mm (5.81 to 6.36 in.)
(4) Tighten the lock nut.
Torque:
26 N·m {260 kgf·cm, 19 ft·lbf}
(5) Install the stop light switch assembly.
Click here ![]()
(h) Install the accelerator pedal.
Click here ![]()
(i) Install the accelerator pedal pad.
Click here ![]()
(j) Install the No. 1 instrument panel under cover sub-assembly.
Click here ![]()
(k) Install the cowl side trim sub-assembly LH.
Click here ![]()
(l) Install the front door scuff plate LH.
Click here ![]()
2. INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY
(a) Inspect the brake pedal stroke sensor assembly.
(1) Connect the Techstream to the DLC3 with the power switch off.
(2) Turn the power switch on (IG).
(3) Turn the Techstream on and enter the following menus: Chassis / ABS/VSC/TRAC / Data List / Stroke Sensor.
Chassis > ABS/VSC/TRAC > Data ListStroke Sensor
(4) Read the stroke sensor value without the brake pedal depressed.
Standard Voltage (without the brake pedal depressed):
0.8 to 1.2 V
HINT:
If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.
(b) Adjust the brake pedal stroke sensor assembly.
(1) Remove the No. 1 instrument panel under cover sub-assembly.
Click here ![]()
(2) Loosen the 2 nuts. NOTICE: Do not depress the brake pedal after turning the power switch on (IG). |
![]() |
(3) Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range. Standard Voltage (without the brake pedal depressed): 0.8 to 1.2 V |
![]() |
(4) Tighten the 2 nuts.
Torque:
8,5 N·m {87 kgf·cm, 75 in·lbf}
(5) Turn the Techstream off and turn the power switch off.
(6) Disconnect the Techstream.
(7) Install the No. 1 instrument panel under cover sub-assembly.
Click here ![]()
(c) Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.
Click here ![]()
3. INSPECT BRAKE PEDAL FREE PLAY
(a) Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration. Brake Pedal Free Play: 1.0 to 6.0 mm (0.0394 to 0.236 in.) HINT:
|
|
4. INSPECT BRAKE PEDAL RESERVE DISTANCE
HINT:
Measure the distance at the same point used for the brake pedal height inspection.
(a) With the power switch on (READY), depress the brake pedal and measure the brake pedal reserve distance.
*1 |
Brake Pedal Pad |
- |
- |
*a |
Brake Pedal Reserve Distance |
*b |
Measuring Plane of Floor Panel |
*c |
36 mm (1.42 in.) |
- |
- |
Brake Pedal Reserve Distance from Floor Panel at 300 N (31 kgf, 67.4 lbf):
85 mm (3.35 in.) or more
HINT:
If the distance is not as specified, troubleshoot the brake system.
Click here ![]()
Components
COMPONENTS
ILLUSTRATION
*1 |
FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
*1 |
NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
- |
- |
ILLUSTRATION
*1 |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
*2 |
BRAKE LINE |
*3 |
BRAKE MASTER CYLINDER GASKET |
*4 |
ENGINE ROOM MAIN WIRE |
*5 |
NO. 1 BRAKE ACTUATOR HOSE |
*6 |
PUSH ROD PIN |
*7 |
CONNECTOR |
*8 |
LOCK NUT |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
* |
For use with a union nut wrench |
● |
Non-reusable part |
![]() |
Lithium soap base glycol grease |
ILLUSTRATION
*1 |
BRAKE PEDAL STROKE SENSOR ASSEMBLY |
*2 |
BRAKE PEDAL SUPPORT ASSEMBLY |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
w/ Rubber Pad |
*B |
w/ Aluminum Pad |
*1 |
BRAKE PEDAL PAD |
*2 |
BRAKE PEDAL RETURN SPRING |
*3 |
BRAKE PEDAL SUPPORT ASSEMBLY |
*4 |
STOP LIGHT SWITCH ASSEMBLY |
*5 |
STOP LIGHT SWITCH MOUNTING ADJUSTER |
*6 |
WIRE HARNESS |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL BRAKE PEDAL PAD
(a) Install the brake pedal pad to the brake pedal support assembly.
HINT:
Installation is easier after applying a small amount of soapy water.
2. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
(a) Engage the 2 claws to install the stop light switch mounting adjuster.
3. INSTALL BRAKE PEDAL RETURN SPRING
(a) Install the brake pedal return spring to the brake pedal support assembly. NOTICE: Attach the bottom part of the brake pedal return spring first, making sure that the open part of the hook is facing the front of the vehicle. Attach the top part of the brake pedal return spring second, making sure that the open part of the hook is facing the rear of the vehicle. |
![]() |
4. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
(a) Install the brake pedal support assembly while avoiding the stud bolts of the brake booster support base.
NOTICE:
Be careful not to deform the bracket of the instrument panel reinforcement assembly.
(b) Install the brake pedal support assembly to the instrument panel reinforcement assembly with the bolt. Torque: 15 N·m {153 kgf·cm, 11 ft·lbf} |
![]() |
(c) Engage the clamp to install the wire harness to the brake pedal support assembly. |
![]() |
5. INSTALL BRAKE MASTER CYLINDER GASKET
Click here ![]()
6. INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Click here ![]()
7. INSTALL PUSH ROD PIN
Click here ![]()
8. INSTALL STOP LIGHT SWITCH ASSEMBLY
Click here ![]()
9. INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY
Click here ![]()
10. CONNECT BRAKE LINE
Click here ![]()
11. CONNECT NO. 1 BRAKE ACTUATOR HOSE
Click here ![]()
12. CONNECT ENGINE ROOM MAIN WIRE
Click here ![]()
13. BLEED NO. 1 BRAKE ACTUATOR TUBE
Click here ![]()
14. CONNECT BRAKE BOOSTER PUMP CONNECTOR
Click here ![]()
HINT:
Perform this operation only when the accumulator pressure zero down operation could not be performed using the Techstream.
15. FILL RESERVOIR WITH BRAKE FLUID
16. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click here ![]()
17. BLEED BRAKE SYSTEM
Click here ![]()
18. INSPECT AND ADJUST BRAKE PEDAL
Click here ![]()
19. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
20. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Click here ![]()
21. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of brake pedal support assembly |
|
|
for Initialization for Calibration: |
NOTICE:
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
PROCEDURE
1. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Click here ![]()
2. REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY
Click here ![]()
3. REMOVE STOP LIGHT SWITCH ASSEMBLY
Click here ![]()
4. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
(a) Disengage the clamp to separate the wire harness from the brake pedal support assembly. |
![]() |
(b) Remove the bolt and separate the brake pedal support assembly from the instrument panel reinforcement assembly. |
![]() |
(c) Remove the 2 clips. HINT: Depending on the vehicle, the clips may not be installed. |
![]() |
(d) Remove the brake pedal support assembly while avoiding the stud bolts of the brake booster support base.
NOTICE:
Be careful not to deform the bracket of the instrument panel reinforcement assembly.
5. REMOVE BRAKE PEDAL RETURN SPRING
(a) Remove the brake pedal return spring from the brake pedal support assembly. |
![]() |
6. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER
(a) Disengage the 2 claws and remove the stop light switch mounting adjuster. |
![]() |
7. REMOVE BRAKE PEDAL PAD
(a) Remove the brake pedal pad from the brake pedal support assembly.















