Linear Solenoid Valve Offset Learning undone (C1345,C1368). Pressure Holding Solenoid Valve Learning Undone (C1349,C134A). Increasing Pressure Solenoid (FR) (C1352-C1359)
Linear Solenoid Valve Offset Learning undone (C1345,C1368)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristics of each linear solenoid built into the brake booster with master cylinder assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.
The skid control ECU (brake booster with master cylinder assembly) receives the shift position P signal from the hybrid vehicle control ECU through the CAN communication system.
These DTCs are cleared when the linear solenoid valve offset learning results are normal.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1345 |
Linear Solenoid Valve Offset Learning undone |
1133 |
The linear solenoid valve offset learning value is not stored. |
Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. |
Only DTC C1345 (INF code 1133) is stored: Does not come on SAE Code C1345 is stored: Comes on |
|
C1368 |
Linear Solenoid Valve Offset |
1134 |
The linear solenoid valve offset learning value cannot be obtained. |
|
Does not come on |
Electronically controlled brake system DTC |
MONITOR DESCRIPTION
SAE Code C1345:- After any of the following situations, if the learning value of the linear solenoid (SLA) or linear solenoid (SLR) is not stored and the vehicle is being driven at a certain speed or more, the skid control ECU (brake booster with master cylinder assembly) judges that the offset learning of the linear solenoid valve is not performed and illuminates the MIL and stores this DTC.
- The skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
- After the brake actuator assembly, brake pedal stroke sensor assembly or brake pedal is removed and installed or replaced, the zero point is cleared.
- After any of the following situations, if learning of the linear solenoid (SLA) or linear solenoid (SLR) has not been performed, or learning has been performed but no learning value was stored, the skid control ECU (brake booster with master cylinder assembly) judges that the offset learning of the linear solenoid valve is not performed and illuminates the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights, blinks* the brake hold operated indicator light and stores this DTC.
- The skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
- After the brake actuator assembly, brake pedal stroke sensor assembly or brake pedal is removed and installed or replaced, the zero point is cleared.
HINT:
- *: The brake hold switch (electric parking brake switch assembly) is turned on under the following vehicle conditions.
- Vehicle Conditions:
- The driver side door is closed.
- The driver side seat belt is fastened.
- Vehicle Conditions:
- As the detection conditions slightly differ from SAE code C1345, the detection conditions for DTC C1345 (INF code 1133) is also provided.
- *: The brake hold switch (electric parking brake switch assembly) is turned on under the following vehicle conditions.
MONITOR STRATEGY
HINT:
SAE code only.
C1345Related DTCs |
C1345: Linear solenoid open current learning not complete |
Required Sensors/Components(Main) |
Skid control ECU (brake booster with master cylinder assembly) |
Required Sensors/Components(Related) |
Speed sensor |
Frequency of Operation |
Continuous |
Duration |
- |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
HINT:
SAE code only.
C1345Monitor runs whenever the following DTCs are not stored |
None |
Vehicle speed |
40 km/h or more |
TYPICAL MALFUNCTION THRESHOLDS
HINT:
SAE code only.
C1345Either of the following conditions is met |
- |
Linear solenoid (SLA) open current learning value |
Not stored |
Linear solenoid (SLR) open current learning value |
Not stored |
COMPONENT OPERATING RANGE
HINT:
SAE code only.
C1345Both of the following conditions are met |
- |
Linear solenoid (SLA) open current learning value |
Stored |
Linear solenoid (SLR) open current learning value |
Stored |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Drive the vehicle at a speed of 40 km/h or more for 1 second.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
HINT:
Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C1203 will be output.
PROCEDURE
CHECK DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check that DTCs other than C1345, C1349 and C1392 are not output.
Click here ![]()
OK:
DTCs other than C1345, C1349 and C1392 are not output.
| NG | REPAIR CIRCUITS INDICATED BY OUTPUT DTCS |
|
PERFORM AIR BLEEDING
(a) Perform the air bleeding procedure in Bleed Brake System.
Click here ![]()
|
PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
(a) Turn the power switch off.
(b) Check and ensure the following conditions required for performing linear solenoid valve offset learning and then perform linear solenoid valve offset learning.
Click here ![]()
ECB Utility
- The auxiliary battery voltage is 11 to 15.5 V when the power switch is on (READY).
- The brake actuator (brake booster with master cylinder assembly) is not hot.
- The hybrid control system is not malfunctioning.
- The shift state indicator shows that the shift lever is in P.
- The READY light in the combination meter assembly is illuminated.
- The brake pedal is not depressed.
- The parking brake is released.
- DTC C1451 (Motor Drive Permission Malfunction) is not output. (If it is output, bleed the air from the high-pressure tube.)
|
RECONFIRM DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs C1345 and C1368 are not output. |
A |
DTCs C1345 and/or C1368 are output. |
B |
| A | END |
| B | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
Pressure Holding Solenoid Valve Learning Undone (C1349,C134A)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristic of each holding solenoid built into the brake actuator assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.
The skid control ECU (brake booster with master cylinder assembly) receives the shift position P signal from the hybrid vehicle control ECU through the CAN communication system.
These DTCs are cleared when the ABS holding solenoid valve learning results are normal.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1349 |
Pressure Holding Solenoid Valve Learning Undone |
1155 |
The ABS holding solenoid valve learning value is not stored. |
Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal. |
Only DTC C1349 (INF code 1155) is stored: Does not come on SAE Code C1349 is stored: Comes on |
|
C134A |
Pressure Holding Solenoid Valve Learning Malfunction |
1156 |
The ABS holding solenoid valve learning value cannot be obtained. |
|
Does not come on |
Electronically controlled brake system DTC |
MONITOR DESCRIPTION
SAE Code C1349:- After any of the following situations, if learning of the ABS holding solenoid for one wheel or more is not stored and the vehicle is being driven at a certain speed or more, the skid control ECU (brake booster with master cylinder assembly) judges that the learning of the ABS holding solenoid valve is not performed and illuminates the MIL and stores this DTC.
- The skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
- After the brake actuator assembly, brake pedal stroke sensor assembly or brake pedal is removed and installed or replaced, the zero point is cleared.
- After any of the following situations, if learning of the ABS holding solenoid for one wheel or more has not been performed, or learning has been performed but no learning value was stored, the skid control ECU (brake booster with master cylinder assembly) judges that the learning of the ABS holding solenoid valve is not performed and illuminates the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights, blinks* the brake hold operated indicator light and stores this DTC.
- The skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
- After the brake actuator assembly, brake pedal stroke sensor assembly or brake pedal is removed and installed or replaced, the zero point is cleared.
HINT:
- *: The brake hold switch (electric parking brake switch assembly) is turned on under the following vehicle conditions.
- Vehicle Conditions:
- The driver side door is closed.
- The driver side seat belt is fastened.
- Vehicle Conditions:
- As the detection conditions slightly differ from SAE code C1349, the detection conditions for DTC C1349 (INF code 1155) is also provided.
- *: The brake hold switch (electric parking brake switch assembly) is turned on under the following vehicle conditions.
MONITOR STRATEGY
HINT:
SAE code only.
C1349Related DTCs |
C1349: ABS holding solenoid open current learning not complete |
Required Sensors/Components(Main) |
Skid control ECU (brake booster with master cylinder assembly) |
Required Sensors/Components(Related) |
Speed sensor |
Frequency of Operation |
Continuous |
Duration |
- |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
HINT:
SAE code only.
C1349Monitor runs whenever the following DTCs are not stored |
None |
Vehicle speed |
40 km/h or more |
TYPICAL MALFUNCTION THRESHOLDS
HINT:
SAE code only.
C1349ABS holding solenoid open current learning value |
Not stored for 1 or more wheels |
COMPONENT OPERATING RANGE
HINT:
SAE code only.
C1349ABS holding solenoid open current learning value |
Stored for 4 wheels |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Drive the vehicle at a speed of 40 km/h or more for 1 second.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
HINT:
Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C1203 will be output.
PROCEDURE
CHECK DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check that DTCs other than C1345, C1349 and C1392 are not output.
Click here ![]()
OK:
DTCs other than C1345, C1349 and C1392 are not output.
| NG | REPAIR CIRCUITS INDICATED BY OUTPUT DTCS |
|
PERFORM AIR BLEEDING
(a) Perform the air bleeding procedure in Bleed Brake System.
Click here ![]()
|
PERFORM ABS HOLDING SOLENOID VALVE LEARNING
(a) Turn the power switch off.
(b) Check and ensure the following conditions required for performing ABS holding solenoid valve learning and then perform ABS holding solenoid valve learning.
Click here ![]()
ECB Utility
- The auxiliary battery voltage is 11 to 15.5 V when the power switch is on (READY).
- The brake actuator assembly is not hot.
- The hybrid control system is not malfunctioning.
- The shift state indicator shows that the shift lever is in P.
- The READY light in the combination meter assembly is illuminated.
- The brake pedal is not depressed.
- The parking brake is released.
NOTICE:
Learning will be performed in the order of linear solenoid valve offset learning and then ABS holding solenoid valve learning.
|
RECONFIRM DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs C1349 and C134A are not output. |
A |
DTCs C1349 and/or C134A are output. |
B |
| A | END |
|
PERFORM ACTIVE TEST USING TECHSTREAM (ABS SOLENOID)
(a) Select the Active Test on the Techstream.
Click here ![]()
Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
ABS Solenoid (SRLH) |
Holding solenoid valve (RLH) |
Solenoid ON/OFF |
- |
ABS Solenoid (SRRH) |
Holding solenoid valve (RRH) |
Solenoid ON/OFF |
- |
ABS Solenoid (SFLH) |
Holding solenoid valve (FLH) |
Solenoid ON/OFF |
- |
ABS Solenoid (SFRH) |
Holding solenoid valve (FRH) |
Solenoid ON/OFF |
- |
ABS Solenoid (SRLH)
Chassis > ABS/VSC/TRAC > Active TestABS Solenoid (SRRH)
Chassis > ABS/VSC/TRAC > Active TestABS Solenoid (SFLH)
Chassis > ABS/VSC/TRAC > Active TestABS Solenoid (SFRH)
(b) Operate the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids one by one. While operating each solenoid, depress the brake pedal, open the corresponding bleeder plug and check that brake fluid does not flow from the bleeder plug.
OK:
Brake fluid does not flow from the corresponding bleeder plug when the brake pedal is depressed when operating each solenoid.
(c) While not operating the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids, depress the brake pedal, open each bleeder plug and check that brake fluid flows from each bleeder plug.
OK:
Brake fluid flows from each bleeder plug when not operating each solenoid and the brake pedal is depressed.
| OK | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| NG | REPLACE BRAKE ACTUATOR ASSEMBLY |
Increasing Pressure Solenoid (FR) (C1352-C1359)
DESCRIPTION
Each solenoid adjusts the pressure which affects each wheel cylinder according to signals from the skid control ECU (brake booster with master cylinder assembly) and controls the vehicle.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1352 |
Increasing Pressure Solenoid (FR) |
11 1100 1101 1102 1103 1170 |
|
|
Comes on |
|
C1353 |
Increasing Pressure Solenoid (FL) |
13 1106 1107 1108 1109 1172 |
|
|
Comes on |
|
C1354 |
Increasing Pressure Solenoid (RR) |
15 1112 1113 1114 1115 1174 |
|
|
Comes on |
|
C1355 |
Increasing Pressure Solenoid (RL) |
17 1118 1119 1120 1121 1176 |
|
|
Comes on |
|
C1356 |
Decreasing Pressure Solenoid (FR) |
12 1104 1105 1171 |
|
|
Comes on |
|
C1357 |
Decreasing Pressure Solenoid (FL) |
14 1110 1111 1173 |
|
|
Comes on |
|
C1358 |
Decreasing Pressure Solenoid (RR) |
16 1116 1117 1175 |
|
|
Comes on |
|
C1359 |
Decreasing Pressure Solenoid (RL) |
18 1122 1123 1177 |
|
|
Comes on |
|
MONITOR DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) monitors the drive voltage and current of the ABS holding solenoid and ABS reduction solenoid. Based on the monitored information, if any of the following abnormal conditions are detected, the MIL is illuminated and a DTC is stored.
- A flyback circuit malfunction is detected.
- A malfunction of the current monitor is detected.
- An open circuit in the holding valve is detected.
- When the monitored current value increases to a value that is not possible when normal.
- A current leakage is detected.
- Output malfunction is detected when there is a solenoid off command.
- An open circuit in the decrease pressure valve is detected.
MONITOR STRATEGY
Related DTCs |
C12A6 (Case 1): ABS holding solenoid range/performance C12A6 (Case 2): ABS holding solenoid range/performance C12A7: ABS holding solenoid circuit low C12A8 (Case 1): ABS holding solenoid circuit high C12A8 (Case 2): ABS holding solenoid circuit high C12A8 (Case 3): ABS holding solenoid circuit high C12B2: ABS reduction solenoid circuit low C12B3 (Case 1): ABS reduction solenoid circuit high C12B3 (Case 2): ABS reduction solenoid circuit high C12B3 (Case 3): ABS reduction solenoid circuit high C12BC (Case 1): ABS holding solenoid range/performance C12BC (Case 2): ABS holding solenoid range/performance C12BD: ABS holding solenoid circuit low C12BE (Case 1): ABS holding solenoid circuit high C12BE (Case 2): ABS holding solenoid circuit high C12BE (Case 3): ABS holding solenoid circuit high C12C8: ABS reduction solenoid circuit low C12C9 (Case 1): ABS reduction solenoid circuit high C12C9 (Case 2): ABS reduction solenoid circuit high C12C9 (Case 3): ABS reduction solenoid circuit high C12D2 (Case 1): ABS holding solenoid range/performance C12D2 (Case 2): ABS holding solenoid range/performance C12D3: ABS holding solenoid circuit low C12D4 (Case 1): ABS holding solenoid circuit high C12D4 (Case 2): ABS holding solenoid circuit high C12D4 (Case 3): ABS holding solenoid circuit high C12DE: ABS reduction solenoid circuit low C12DF (Case 1): ABS reduction solenoid circuit high C12DF (Case 2): ABS reduction solenoid circuit high C12DF (Case 3): ABS reduction solenoid circuit high C12E8 (Case 1): ABS holding solenoid range/performance C12E8 (Case 2): ABS holding solenoid range/performance C12E9: ABS holding solenoid circuit low C12EA (Case 1): ABS holding solenoid circuit high C12EA (Case 2): ABS holding solenoid circuit high C12EA (Case 3): ABS holding solenoid circuit high C12F4: ABS reduction solenoid circuit low C12F5 (Case 1): ABS reduction solenoid circuit high C12F5 (Case 2): ABS reduction solenoid circuit high C12F5 (Case 3): ABS reduction solenoid circuit high |
Required Sensors/Components(Main) |
Skid control ECU (brake booster with master cylinder assembly) Brake actuator assembly |
Required Sensors/Components(Related) |
Skid control ECU (brake booster with master cylinder assembly) Brake actuator assembly |
Frequency of Operation |
Continuous |
Duration |
54 times: C12B2, C12C8, C12DE and C12F4 0.054 seconds: C12A6 (Case 1 and 2), C12A7, C12A8 (Case 1, 2 and 3), C12B3 (Case 1, 2 and 3), C12BC (Case 1 and 2), C12BD, C12BE (Case 1, 2 and 3), C12C9 (Case 1, 2 and 3), C12D2 (Case 1 and 2), C12D3, C12D4 (Case 1, 2 and 3), C12DF (Case 1, 2 and 3), C12E8 (Case 1 and 2), C12E9, C12EA (Case 1, 2 and 3) and C12F5 (Case 1, 2 and 3) |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
AllMonitor runs whenever the following DTCs are not stored |
None |
Serial communication with low side IC |
Valid |
All of the following conditions are met |
- |
Power supply for ABS solenoid |
Higher than 9.13 V |
Serial communication with low side IC |
Valid |
Output duty cycle |
Higher than 40% |
ABS holding solenoid current monitor |
Normal |
ABS solenoid power supply relay |
On |
Both of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
Current monitor power supply |
Higher than 1.2 V, and less than 1.38 V |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
ABS solenoid power supply relay |
On |
Output duty cycle |
0% |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
Power supply for ABS solenoid |
Higher than 9.13 V |
Output duty cycle |
0% |
ABS solenoid power supply relay |
On |
All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
Command to reduction solenoid on/off |
On |
ABS reduction solenoid current |
Less than 4.4 A |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
ABS solenoid power supply relay |
On |
Command to reduction solenoid on/off |
Off |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
Power supply for ABS solenoid |
Higher than 9.13 V |
Command to reduction solenoid on/off |
Off |
ABS solenoid power supply relay |
On |
TYPICAL MALFUNCTION THRESHOLDS
C12A6, C12BC, C12D2 and C12E8 (Case 1)ABS holding solenoid voltage |
Higher than 35 V |
One of the following conditions is met |
A, B or C |
A. Both of the following conditions are met |
- |
ABS holding solenoid current monitor value |
Less than 46 |
ABS holding solenoid current |
Less than 3.5 A |
B. Current monitor power supply |
Higher than 1.38 V, or less than 1.2 V |
C. AC/DC converter built into CPU standard voltage |
Less than 4.4 V |
ABS holding solenoid current |
Less than 0.2 A |
ABS holding solenoid current |
Higher than 3.5 A |
ABS holding solenoid voltage |
Less than 11.25 V |
ABS holding solenoid voltage |
Less than 4.128 V |
Either of the following conditions is met |
- |
ABS reduction solenoid voltage |
Higher than 4.2 V |
ABS reduction solenoid current |
Less than 0.02 A |
ABS reduction solenoid current |
Higher than 4.4 A |
ABS reduction solenoid voltage |
Less than 11.25 V |
ABS reduction solenoid voltage |
Less than 4.128 V |
COMPONENT OPERATING RANGE
C12A6, C12BC, C12D2 and C12E8 (Case 1)All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
Output duty cycle |
Higher than 0% |
Low side IC malfunction |
Not detected |
ABS holding solenoid voltage |
Less than 35 V |
All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
ABS holding solenoid current monitor value |
46 or more |
Current monitor power supply |
1.38 V or less, and 1.2 V or more |
AC/DC converter built into CPU standard voltage |
Higher than 4.4 V |
All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
Output duty cycle |
Higher than 40% |
ABS holding solenoid current monitor |
Normal |
ABS holding solenoid current |
0.2 A or more |
All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
Output duty cycle |
Higher than 0% |
Low side IC malfunction |
Not detected |
ABS holding solenoid current |
Less than 3.5 A |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
ABS solenoid power supply relay |
On |
Output duty cycle |
0% |
ABS holding solenoid voltage |
Higher than 11.29 V |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
ABS solenoid power supply relay |
On |
Output duty cycle |
0% |
ABS holding solenoid voltage |
Higher than 4.2 V |
All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
Command to reduction solenoid on/off |
On |
Low side IC malfunction |
Not detected |
ABS reduction solenoid voltage |
Less than 4.128 V |
ABS reduction solenoid current |
Higher than 0.02 A |
All of the following conditions are met |
- |
ABS solenoid power supply relay |
On |
Serial communication with low side IC |
Valid |
Command to reduction solenoid on/off |
On |
Low side IC malfunction |
Not detected |
ABS reduction solenoid current |
Less than 4.4 A |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
ABS solenoid power supply relay |
On |
Command to reduction solenoid on/off |
Off |
ABS reduction solenoid voltage |
Higher than 11.29 V |
All of the following conditions are met |
- |
Serial communication with low side IC |
Valid |
ABS solenoid power supply relay |
On |
Command to reduction solenoid on/off |
Off |
ABS reduction solenoid voltage |
Higher than 4.2 V |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Drive the vehicle at a speed of 20 km/h for 1 minute.
- Operate the ABS using a drum tester or equivalent.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
WIRING DIAGRAM
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
PROCEDURE
INSPECT BRAKE ACTUATOR ASSEMBLY
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
*a |
Component without harness connected (Brake Actuator Assembly) |
- |
- |
(b) Disconnect the A39 brake actuator assembly connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
HINT:
Check the brake actuator assembly when it is cooled down.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
5 (+BS) - 28 (SFRH) |
Always |
6.4 to 7.0 Ω |
5 (+BS) - 31 (SFLH) |
Always |
6.4 to 7.0 Ω |
5 (+BS) - 30 (SRRH) |
Always |
6.4 to 7.0 Ω |
5 (+BS) - 29 (SRLH) |
Always |
6.4 to 7.0 Ω |
5 (+BS) - 18 (SFRR) |
Always |
5.1 to 5.7 Ω |
5 (+BS) - 15 (SFLR) |
Always |
5.1 to 5.7 Ω |
5 (+BS) - 16 (SRRR) |
Always |
5.1 to 5.7 Ω |
5 (+BS) - 17 (SRLR) |
Always |
5.1 to 5.7 Ω |
| NG | REPLACE BRAKE ACTUATOR ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-14 (+BS) - A39-5 (+BS) |
Always |
Below 1 Ω |
A35-14 (+BS) or A39-5 (+BS) - Body ground |
Always |
10 kΩ or higher |
A35-48 (SFRH) - A39-28 (SFRH) |
Always |
Below 1 Ω |
A35-48 (SFRH) or A39-28 (SFRH) - Body ground |
Always |
10 kΩ or higher |
A35-49 (SFLH) - A39-31 (SFLH) |
Always |
Below 1 Ω |
A35-49 (SFLH) or A39-31 (SFLH) - Body ground |
Always |
10 kΩ or higher |
A35-50 (SRRH) - A39-30 (SRRH) |
Always |
Below 1 Ω |
A35-50 (SRRH) or A39-30 (SRRH) - Body ground |
Always |
10 kΩ or higher |
A35-51 (SRLH) - A39-29 (SRLH) |
Always |
Below 1 Ω |
A35-51 (SRLH) or A39-29 (SRLH) - Body ground |
Always |
10 kΩ or higher |
A35-44 (SFRR) - A39-18 (SFRR) |
Always |
Below 1 Ω |
A35-44 (SFRR) or A39-18 (SFRR) - Body ground |
Always |
10 kΩ or higher |
A35-45 (SFLR) - A39-15 (SFLR) |
Always |
Below 1 Ω |
A35-45 (SFLR) or A39-15 (SFLR) - Body ground |
Always |
10 kΩ or higher |
A35-46 (SRRR) - A39-16 (SRRR) |
Always |
Below 1 Ω |
A35-46 (SRRR) or A39-16 (SRRR) - Body ground |
Always |
10 kΩ or higher |
A35-47 (SRLR) - A39-17 (SRLR) |
Always |
Below 1 Ω |
A35-47 (SRLR) or A39-17 (SRLR) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
RECONFIRM DTC
(a) Reconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(b) Reconnect the A39 brake actuator assembly connector.
(c) Clear the DTCs.
Click here ![]()
(d) Turn the power switch off.
(e) Turn the power switch on (IG).
(f) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 and C1359 are not output. |
A |
DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 and/or C1359 are output. |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |