Malfunction in Motor (C1427). Motor Circuit (C1428). Steering Angle Sensor Power Source Voltage (C1432)
Malfunction in Motor (C1427)
DESCRIPTION
When the power switch is on (READY), the stop light switch assembly off and the vehicle speed is 20 km/h or more, the skid control ECU (brake booster with master cylinder assembly) performs a self-diagnosis of the ABS motor relay circuit during the initial check of the actuator.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1427 |
Malfunction in Motor |
1159 |
The pump motor built into the brake actuator assembly is not operating correctly. |
|
Comes on |
|
MONITOR DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) monitors the voltage of the ABS motor. When the ABS motor is normal and the ABS motor relay is turned off, the voltage of the ABS motor drops gradually due to rotational inertia; however, if the ABS motor is not turning and the ABS motor relay is turned off, the voltage of the ABS motor drops immediately. If the voltage of the ABS motor drops considerably quickly when the ABS motor relay is turned off, the skid control ECU (brake booster with master cylinder assembly) judges that the ABS motor is not operating and illuminates the MIL and stores this DTC.
MONITOR STRATEGY
Related DTCs |
C1427: ABS pump motor stuck |
Required Sensors/Components(Main) |
Brake actuator assembly |
Required Sensors/Components(Related) |
Skid control ECU (brake booster with master cylinder assembly) Brake actuator assembly |
Frequency of Operation |
Continuous |
Duration |
2 times |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
- |
Skid control ECU (brake booster with master cylinder assembly) state |
Initial check |
After command to ABS motor relay on to off detection, 0.002 seconds passes |
Met |
TYPICAL MALFUNCTION THRESHOLDS
ABS pump motor voltage |
Less than 1.3 V for 0.022 seconds or more within 0.024 seconds |
COMPONENT OPERATING RANGE
All of the following conditions are met |
- |
Skid control ECU (brake booster with master cylinder assembly) state |
Initial check |
After command to ABS motor relay on to off detection, 0.002 seconds passes |
Met |
ABS pump motor voltage |
Less than 1.3 V for less than 0.022 seconds within 0.024 seconds |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (READY).
- Turn the Techstream on.
- Drive the vehicle at a speed of 20 km/h or more for 1 minute.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
WIRING DIAGRAM
NOTICE:
- After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
(a) Select the Active Test on the Techstream.
Click here ![]()
Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Motor Relay |
ABS motor relay |
Relay ON/OFF |
Operating sound of motor can be heard. |
Motor Relay
(b) Check the operating sound of the ABS motor relay when operating it with the Techstream.
Result | Proceed to |
|---|---|
The operating sound is heard. |
A |
The operating sound is not heard. |
B |
| B | GO TO STEP 3 |
|
RECONFIRM DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (READY).
(d) Perform a road test.
(e) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTC C1427 is not output. |
A |
DTC C1427 is output. |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
(a) Turn the power switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(d) Disconnect the A39 brake actuator assembly connector.
(e) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-40 (+BM) - A39-10 (+BM) |
Always |
Below 1 Ω |
A35-40 (+BM) or A39-10 (+BM) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (GND TERMINAL)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT) |
|
RECONFIRM DTC
(a) Reconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(b) Reconnect the A39 brake actuator assembly connector.
(c) Clear the DTCs.
Click here ![]()
(d) Turn the power switch off.
(e) Turn the power switch on (READY).
(f) Perform a road test.
(g) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTC C1427 is not output. |
A |
DTC C1427 is output. |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE ACTUATOR ASSEMBLY |
Motor Circuit (C1428)
DESCRIPTION
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1428 |
Motor Circuit |
611 1160 |
|
Brake actuator assembly |
Comes on |
|
MONITOR DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) monitors the voltage of the ABS motor. When the ABS motor relay is instructed to be off and the voltage of the ABS motor is at a value that is not possible when normal, the skid control ECU (brake booster with master cylinder assembly) judges that the circuit of the ABS motor is malfunctioning and illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
C052B: ABS pump motor range/performance C052D (Case 2): ABS pump motor circuit high |
Required Sensors/Components(Main) |
Brake actuator assembly |
Required Sensors/Components(Related) |
Skid control ECU (brake booster with master cylinder assembly) |
Frequency of Operation |
Continuous |
Duration |
0.2 seconds: C052D (Case 2) 2 seconds: C052B |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
AllMonitor runs whenever the following DTCs are not stored |
None |
Command to ABS motor relay |
Off |
TYPICAL MALFUNCTION THRESHOLDS
C052BABS pump motor voltage |
Higher than 1.448 V, and less than 7.607 V |
ABS pump motor voltage |
18.57 V or more |
COMPONENT OPERATING RANGE
C052BBoth of the following conditions are met |
- |
Command to ABS motor relay |
Off |
ABS pump motor voltage |
1.448 V or less, or 7.607 V or more |
ABS pump motor voltage |
Less than 18.57 V |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Wait 2 seconds.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the judgment result is INCOMPLETE or N/A and no pending DTCs are output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
WIRING DIAGRAM
Refer to DTC C1427.
Click here ![]()
NOTICE:
After replacing the brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
PROCEDURE
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(c) Disconnect the A39 brake actuator assembly connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-40 (+BM) - A39-10 (+BM) |
Always |
Below 1 Ω |
A35-40 (+BM) or A39-10 (+BM) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (GND TERMINAL)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK | REPLACE BRAKE ACTUATOR ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT) |
Steering Angle Sensor Power Source Voltage (C1432)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1432 |
Steering Angle Sensor Power Source Voltage |
703 |
Steering angle sensor power supply malfunction signal is received from steering angle sensor. |
|
Does not come on |
VSC DTC |
WIRING DIAGRAM
Refer to DTC C1434.
Click here ![]()
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
(a) Remove the steering wheel and column cover. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the G48 steering angle sensor connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G48-4 (BAT) - Body ground |
Always |
11 to 14 V |
G48-9 (IG) - Body ground |
Power switch on (IG) |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
|
CHECK HARNESS AND CONNECTOR (GND TERMINAL)
(a) Turn the power switch off. |
|
(b) Measure the resistance according to the value(s) in the table below.
NOTICE:
Before measuring the resistance of the steering angle sensor, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G48-6 (ESS) - Body ground |
1 minute after power switch off |
Below 1 Ω |
| OK | REPLACE STEERING ANGLE SENSOR |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT) |



