Diagnosis System. Diagnostic Trouble Code Chart. Dtc Check / Clear
Diagnosis System
DIAGNOSIS SYSTEM
DESCRIPTION
When troubleshooting a vehicle with a diagnosis system, the only difference from the usual troubleshooting procedure is connecting the Techstream to the vehicle and reading various data output from the skid control ECU (brake actuator assembly).
The skid control ECU (brake actuator assembly) records DTCs when it detects a malfunction in itself or in its circuits.
To check for DTCs, connect the Techstream to the DLC3 on the vehicle. The Techstream can be used to clear the DTCs, activate various actuators, and check the Freeze Frame Data and Data List.
(a) Check the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge the battery before proceeding to the next step.
(b) Check the DLC3.
Click here ![]()
DIAGNOSIS
(a) If a malfunction occurs in one part of the system, the skid control ECU (brake actuator assembly) illuminates the warning light corresponding to the malfunctioning system (ABS warning light, brake system warning light (red indicator) or slip indicator light).
(b) If a DTC is stored by the skid control ECU (brake actuator assembly) and the following conditions are met when the brake hold switch (electric parking brake switch assembly) is pressed, the brake hold operated indicator light blinks.
- Vehicle Conditions:
- The driver door is closed.
- The driver seat belt is fastened.
(c) DTCs are simultaneously stored in memory.
The DTCs can be read by connecting the Techstream.
Click here ![]()
(d) This system has a Test Mode (Signal Check) function.
Click here ![]()
WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
(a) When the engine switch is turned on (IG), check that the ABS warning light, brake system warning light (red indicator), VSC OFF indicator light, brake hold standby indicator light, brake hold operated indicator light and slip indicator light come on for approximately 3 seconds.
HINT:
- When the brake fluid level is low or the vacuum inside the brake booster decreases, the brake system warning light (red indicator) comes on.
- If the warning light and indicator light check result is not normal, proceed to troubleshooting for the ABS warning light, brake system warning light (red indicator), VSC OFF indicator light, slip indicator light, brake hold standby indicator light and brake hold operated indicator light circuits.
- If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
Trouble Area | See Procedure |
|---|---|
ABS warning light circuit (Remains on) |
|
ABS warning light circuit (Does not come on) |
|
Brake system warning light (red indicator) circuit (Remains on) |
|
Brake system warning light (red indicator) circuit (Does not come on) |
|
VSC OFF indicator light circuit (Remains on) |
|
VSC OFF indicator light circuit (Does not come on) |
|
Slip indicator light circuit (Remains on) |
|
Slip indicator light circuit (Does not come on) |
|
Brake hold standby indicator light circuit |
|
Brake hold operated indicator light circuit |
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Vehicle Stability Control SystemDTC No. | Detection Item | Link |
|---|---|---|
C1201 |
Engine Control System Malfunction |
|
C1224 |
NE Signal Circuit |
|
C1225 |
SA1 Solenoid Circuit |
|
C1226 |
SA2 Solenoid Circuit |
|
C1227 |
SA3 Solenoid Circuit |
|
C1228 |
STR Solenoid Circuit |
|
C1231 |
Steering Angle Sensor Circuit |
|
C1234 |
Yaw Rate Sensor |
|
C1237 |
Speed Sensor Rotor Faulty |
|
C1241 |
Low or High Power Supply Voltage |
|
C1246 |
Master Cylinder Pressure Sensor |
|
C1249 |
Open Circuit in Stop Light Switch Circuit |
|
C1288 |
Error in Matching of ECUs |
|
C1300 |
Skid Control ECU Malfunction |
|
C1330 |
Open Circuit in Right Front Speed Sensor Circuit |
|
C1331 |
Open Circuit in Left Front Speed Sensor Circuit |
|
C1332 |
Open Circuit in Right Rear Speed Sensor Circuit |
|
C1333 |
Open Circuit in Left Rear Speed Sensor Circuit |
|
C1336 |
Zero Point Calibration of Deceleration Sensor undone |
|
C1380 |
Stop Light Relay Malfunction |
|
C1381 |
Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor |
|
C1417 |
IG1 Voltage Supply too High |
|
C1419 |
Deceleration Sensor Internal Circuit |
|
C1420 |
Malfunction in Deceleration Sensor |
|
C1425 |
Open in Stop Light Switch Circuit |
|
C1426 |
Stop Switch OFF Stuck |
|
C1428 |
Motor Circuit |
|
C1432 |
Steering Angle Sensor Power Source Voltage |
|
C1433 |
Steering Angle Sensor Internal Circuit |
|
C1434 |
Steering Angle Sensor Output |
|
C1435 |
Yaw Rate Sensor Internal Circuit |
|
C1436 |
Malfunction in Yaw Rate Sensor |
|
C1439 |
Steering Angle Sensor Initialization Incomplete |
|
C1445 |
Vehicle Driven with Steering Angle Sensor not Initialized |
|
C1448 |
Yaw Rate Sensor Output Value Malfunction |
|
C1464 |
Front Speed Sensor RH Circuit |
|
C1465 |
Front Speed Sensor LH Circuit |
|
C1466 |
Rear Speed Sensor RH Circuit |
|
C1467 |
Rear Speed Sensor LH Circuit |
|
C1468 |
SFR Solenoid Circuit |
|
C1469 |
SFL Solenoid Circuit |
|
C146A |
SRR Solenoid Circuit |
|
C146B |
SRL Solenoid Circuit |
|
C146C |
Open Circuit in ABS Motor Relay Circuit |
|
C146E |
Open Circuit in ABS Solenoid Relay Circuit |
|
C1472 |
Deceleration Sensor |
|
C1474 |
Forward and Rearward G Sensor |
|
C147D |
Air Bag Circuit |
|
U0073 |
Control Module Communication Bus Off |
|
U0100 |
Lost Communication With ECM/PCM "A" |
|
U0123 |
Lost Communication With Yaw Rate Sensor Module |
|
U0126 |
Lost Communication With Steering Angle Sensor Module |
|
U0142 |
Lost Communication with Body Control Module "B" |
|
U0151 |
Lost Communication With Restraints Control Module |
Dtc Check / Clear
DTC CHECK / CLEAR
DTC CHECK/CLEAR (When Using TECHSTREAM)
(a) Check for DTCs.
(1) Turn the engine switch off.
(2) Connect the Techstream to the DLC3.
(3) Turn the engine switch on (IG).
(4) Turn the Techstream on.
(5) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Trouble Codes.
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes(6) Check the details of the DTCs.
Click here ![]()
NOTICE:
The vehicle stability control system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the vehicle stability control system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
System |
Proceed to |
Electric Parking Brake System |
(b) Clear the DTCs.
(1) Turn the engine switch off.
(2) Connect the Techstream to the DLC3.
(3) Turn the engine switch on (IG).
(4) Turn the Techstream on.
(5) Operate the Techstream to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Trouble Codes.
Chassis > ABS/VSC/TRAC/EPB > Clear DTCs(6) Press the DTC clear button.
END OF DTC CHECK/CLEAR
(a) Turn the engine switch on (IG).
(b) Check that the ABS warning, slip indicator and brake hold operated indicator* lights go off within approximately 3 seconds of turning the engine switch on (IG).
*: The brake hold switch (electric parking brake switch assembly) is pressed under the following vehicle conditions.
- Vehicle Conditions:
- The driver door is closed.
- The driver seat belt is fastened.


