Motor Circuit (C1428). Steering Angle Sensor Power Source Voltage (C1432). Steering Angle Sensor Internal Circuit (C1433)
Motor Circuit (C1428)
DESCRIPTION
This DTC is stored when the skid control ECU (brake actuator assembly) judges that an abnormality occurred in the circuit used to operate the pump motor.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1428 |
Motor Circuit |
A malfunction occurs in the pump motor circuit. |
Pump motor circuit |
WIRING DIAGRAM
Refer to DTC C146C.
Click here ![]()
NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector. OK: The connector is securely connected. |
|
(b) Disconnect the A28 skid control ECU (brake actuator assembly) connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A28-1 (+BM) - Body ground |
Always |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT) |
|
CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT) |
|
RECONFIRM DTC
(a) Reconnect the A28 skid control ECU (brake actuator assembly) connector.
(b) Clear the DTCs.
Chassis > ABS/VSC/TRAC/EPB > Clear DTCs(c) Turn the engine switch off.
(d) Start the engine.
(e) Perform a road test.
(f) Check if the same DTC is output.
Chassis > ABS/VSC/TRAC/EPB > Trouble CodesResult | Proceed to |
|---|---|
C1428 is not output |
A |
C1428 is output |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE ACTUATOR ASSEMBLY |
Steering Angle Sensor Power Source Voltage (C1432)
DESCRIPTION
This DTC is stored when the skid control ECU (brake actuator assembly) receives a +B line open signal from the steering angle sensor.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1432 |
Steering Angle Sensor Power Source Voltage |
With the +BS terminal voltage between 9.6 and 16.5 V, a steering angle sensor power supply circuit malfunction signal is received from the steering angle sensor. |
|
WIRING DIAGRAM
Refer to DTC C1231.
Click here ![]()
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
(a) Remove the steering wheel and column cover. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the G48 steering angle sensor connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G48-4 (BAT) - Body ground |
Always |
11 to 14 V |
G48-9 (IG1) - Body ground |
Engine switch on (IG) |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
|
CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
(a) Turn the engine switch off. |
|
(b) Measure the resistance according to the value(s) in the table below.
NOTICE:
Before measuring the resistance of the steering angle sensor, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G48-6 (ESS) - Body ground |
1 minute after engine switch off |
Below 1 Ω |
| OK | REPLACE STEERING ANGLE SENSOR |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT) |
Steering Angle Sensor Internal Circuit (C1433)
DESCRIPTION
This DTC is stored when the skid control ECU (brake actuator assembly) receives an internal malfunction signal from the steering angle sensor.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1433 |
Steering Angle Sensor Internal Circuit |
With the +BS terminal voltage between 9.6 and 16.5 V, a steering angle sensor malfunction signal is received from the steering angle sensor. |
Steering angle sensor |
PROCEDURE
REPLACE STEERING ANGLE SENSOR
(a) Replace the steering angle sensor.
Click here ![]()
| NEXT | END |



