Definition Of Terms. Diagnosis System. Diagnostic Trouble Code Chart
Definition Of Terms
DEFINITION OF TERMS
Term | Definition |
|---|---|
Monitor Description |
Description of what the skid control ECU (brake booster with master cylinder assembly) monitors and how it detects malfunctions (monitoring purpose and details). |
Related DTCs |
Group of diagnostic trouble codes that are output by the skid control ECU (brake booster with master cylinder assembly) based on the same malfunction detection logic. |
Typical Enabling Conditions |
Preconditions that allow the skid control ECU (brake booster with master cylinder assembly) to detect malfunctions. With all preconditions satisfied, the skid control ECU (brake booster with master cylinder assembly) stores a DTC when the monitored value(s) exceeds the malfunction threshold(s). |
Sequence of Operation |
The priority order that is applied to monitoring if multiple sensors and components are used to detect the malfunction. While one sensor is being monitored, the next sensor or component will not be monitored. |
Required Sensors/Components |
The sensors and components that are used by the skid control ECU (brake booster with master cylinder assembly) to detect malfunctions. |
Frequency of Operation |
The number of times that the skid control ECU (brake booster with master cylinder assembly) checks for malfunctions per driving cycle. "Continuous" means that the skid control ECU (brake booster with master cylinder assembly) checks for malfunctions every time the enabling conditions are met. "During initial checking" means that the skid control ECU (brake booster with master cylinder assembly) checks for malfunctions for approximately 3 seconds after the power switch is turned on (IG) (while the initial check being performed). "After power switch off" means that after the power switch is turned off, the system check which is performed using residual power checks for malfunctions that are difficult to detect during normal operation, within a certain amount of time. |
Duration |
The minimum time for which the skid control ECU (brake booster with master cylinder assembly) must detect a continuous deviation in the monitored value(s) in order to store a DTC. Timing begins after the "typical enabling conditions" are met. |
Typical Malfunction Thresholds |
Value beyond which the skid control ECU (brake booster with master cylinder assembly) will determine that there is a malfunction and stores a DTC. |
MIL Operation |
MIL illumination timing after a malfunction is detected. "Immediate" means that the skid control ECU (brake booster with master cylinder assembly) illuminates the MIL the instant the skid control ECU (brake booster with master cylinder assembly) determines that there is a malfunction. |
Component Operating Range |
Normal operation range of sensors and solenoids under normal driving conditions. Use these ranges as a reference. They cannot be used to judge if a sensor or solenoid is defective or not. |
Diagnosis System
DIAGNOSIS SYSTEM
DESCRIPTION
When troubleshooting a vehicle with a diagnosis system, the only difference from the usual troubleshooting procedure is connecting the Techstream to the vehicle and reading various data output from the skid control ECU (brake booster with master cylinder assembly).
The skid control ECU (brake booster with master cylinder assembly) records DTCs when it detects a malfunction in itself or in its circuits.
To check for DTCs, connect the Techstream to the DLC3 on the vehicle. The Techstream can be used to clear the DTCs, activate various actuators, and check the Freeze Frame Data and Data List.
(a) Check the auxiliary battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge the auxiliary battery before proceeding to the next step.
(b) Check the DLC3.
Click here ![]()
DIAGNOSIS
(a) If the skid control ECU (brake booster with master cylinder assembly) detects a malfunction, the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights will come on in order to warn the driver. Also, if the vehicle is under the following conditions and the brake hold switch (electric parking brake switch assembly) is turned on, the brake hold operated indicator light blinks.
- Vehicle Conditions:
- The driver side door is closed.
- The driver side seat belt is fastened.
(b) DTCs are simultaneously stored in memory.
The DTCs can be read by connecting the Techstream.
Click here ![]()
(c) This system has a Test Mode (Signal Check) function.
Click here ![]()
DTC FOR RELATED SYSTEM MALFUNCTION
(a) When the skid control ECU (brake booster with master cylinder assembly) detects DTCs stored by related systems, it stores DTCs to indicate the malfunctioning system.
DTC for Related System MalfunctionMalfunctioning System | Output DTC | DTC Storage | System/Control Condition |
|---|---|---|---|
Hybrid control system |
DTC C1310 (INF code 1140) |
Current and history DTCs are cleared when the system returns to normal. |
VSC system is disabled |
DTC C1310 (INF code 1141) |
Brake hold control operation is prohibited |
||
Electric parking brake system |
DTC C13AF DTC U0128 |
Current DTCs are cleared when the system returns to normal. |
Brake hold control operation is prohibited |
Airbag system |
DTC C147D DTC U0151 |
Current DTCs are cleared when the system returns to normal. |
Secondary collision brake control operation is prohibited |
HINT:
The above DTCs may be stored in the skid control ECU (brake booster with master cylinder assembly) even if it was never stored as a history DTC or cleared in the system that caused the DTC to be stored.
WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
(a) When the power switch is turned on (IG), check that the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction), VSC OFF indicator, slip indicator, brake hold standby indicator and brake hold operated indicator lights all come on for approximately 3 seconds.
HINT:
- When the brake fluid level is low, the brake warning light / red (malfunction) comes on.
- If the warning light and indicator light check results are not normal, proceed to troubleshooting for the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction), VSC OFF indicator, slip indicator, brake hold standby indicator and brake hold operated indicator light circuits.
- If an indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
Trouble Area | See Procedure |
|---|---|
ABS warning light circuit (Remains on) |
|
ABS warning light circuit (Does not come on) |
|
Brake warning light / red (malfunction) circuit (Remains on) |
|
Brake warning light / red (malfunction) circuit (Does not come on) |
|
Brake warning light / yellow (minor malfunction) circuit (Remains on) |
|
Brake warning light / yellow (minor malfunction) circuit (Does not come on) |
|
VSC OFF indicator light circuit (Remains on) |
|
VSC OFF indicator light circuit (Does not come on) |
|
Slip indicator light circuit (Remains on) |
|
Slip indicator light circuit (Does not come on) |
|
Brake hold standby indicator light circuit |
|
Brake hold operated indicator light circuit |
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Electronically Controlled Brake SystemDTC No. | Detection Item | INF Code | MIL | Note | Link |
|---|---|---|---|---|---|
C1202 |
Master Reservoir Level Malfunction |
1126 |
Comes on |
HINT: DTC C1202 (INF code 1126) is cleared when the conditions return to normal. |
|
C1203 |
ECM Communication Circuit |
1161 |
Comes on |
HINT:
|
|
C120F |
Open in Master Reservoir Level Switch Circuit |
371 |
Comes on |
|
|
C1210 |
Zero Point Calibration of Yaw Rate Sensor undone |
1139 |
Does not come on |
VSC DTC |
|
C1211 |
SLA Linear Solenoid |
21 22 23 24 25 26 |
Comes on |
|
|
C1212 |
SLR Linear Solenoid |
31 32 33 34 35 36 |
Comes on |
|
|
C1214 |
Hydraulic Control System Malfunction |
431 432 436 438 440 441 442 |
Comes on |
|
|
C1225 |
SA1 Solenoid Circuit |
41 42 43 44 45 46 |
Comes on |
|
|
C1226 |
SA2 Solenoid Circuit |
71 72 73 74 75 76 |
Comes on |
|
|
C1232 |
Deceleration Sensor |
562 563 |
Comes on |
|
|
C1240 |
Yaw Rate Sensor discrimination |
406 |
Comes on |
|
|
C1241 |
Low or High Power Supply Voltage |
101 102 103 551 552 554 |
Comes on |
|
|
C1242 |
Open Circuit in IG1/IG2 Power Source Circuit |
111 112 |
Comes on |
|
|
C1243 |
Deceleration Sensor Stuck |
561 564 565 |
Comes on |
|
|
C1245 |
Abnormal Output in Deceleration Sensor |
581 |
Comes on |
|
|
C1247 |
Stroke Sensor |
211 212 213 214 215 216 217 |
Comes on |
|
|
C1252 |
Brake Booster Pump Motor on Time Abnormally Long |
311 |
Comes on |
|
|
C1253 |
Pump Motor Relay |
321 322 327 328 |
Comes on (When only SAE code C121D or SAE code C121E is stored) |
|
|
C1256 |
Accumulator Low Pressure |
341 1125 |
Comes on (When only SAE code C1256 is stored) |
|
|
C1257 |
Power Supply Drive Circuit |
361 362 |
Does not come on |
Electronically controlled brake system DTC |
|
C1259 |
HV Control System Regenerative Malfunction |
1132 |
Does not come on |
Electronically controlled brake system DTC HINT: The DTC is cleared when the conditions return to normal. |
|
C1290 |
Abnormal Zero Point of Steering Angle Sensor |
751 |
Does not come on |
VSC DTC |
|
C1300 |
Skid Control ECU Malfunction |
1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 |
Comes on |
|
|
C1310 |
HV System Malfunction |
1140 1141 |
Does not come on |
|
|
C1311 |
Open Circuit in Main Relay 1 |
1 |
Comes on |
|
|
C1312 |
Short Circuit in Main Relay 1 |
2 |
Comes on |
|
|
C1336 |
Zero Point Calibration of Deceleration Sensor undone |
1138 |
Only DTC C1336 (INF code 1138) is stored: Does not come on SAE Code C1336 is stored: Comes on |
|
|
C1345 |
Linear Solenoid Valve Offset Learning undone |
1133 |
Only DTC C1345 (INF code 1133) is stored: Does not come on SAE Code C1345 is stored: Comes on |
|
|
C1349 |
Pressure Holding Solenoid Valve Learning Undone |
1155 |
Only DTC C1349 (INF code 1155) is stored: Does not come on SAE Code C1349 is stored: Comes on |
|
|
C134A |
Pressure Holding Solenoid Valve Learning Malfunction |
1156 |
Does not come on |
Electronically controlled brake system DTC |
|
C1352 |
Increasing Pressure Solenoid (FR) |
11 1100 1101 1102 1103 1170 |
Comes on |
|
|
C1353 |
Increasing Pressure Solenoid (FL) |
13 1106 1107 1108 1109 1172 |
Comes on |
|
|
C1354 |
Increasing Pressure Solenoid (RR) |
15 1112 1113 1114 1115 1174 |
Comes on |
|
|
C1355 |
Increasing Pressure Solenoid (RL) |
17 1118 1119 1120 1121 1176 |
Comes on |
|
|
C1356 |
Decreasing Pressure Solenoid (FR) |
12 1104 1105 1171 |
Comes on |
|
|
C1357 |
Decreasing Pressure Solenoid (FL) |
14 1110 1111 1173 |
Comes on |
|
|
C1358 |
Decreasing Pressure Solenoid (RR) |
16 1116 1117 1175 |
Comes on |
|
|
C1359 |
Decreasing Pressure Solenoid (RL) |
18 1122 1123 1177 |
Comes on |
|
|
C1368 |
Linear Solenoid Valve Offset |
1134 |
Does not come on |
Electronically controlled brake system DTC |
|
C1380 |
Stop Light Control Relay Malfunction |
761 762 |
Does not come on |
VSC DTC |
|
C1381 |
Abnormal Power Supply Voltage in Yaw Rate and/or Deceleration Sensor |
601 |
Comes on |
|
|
C1391 |
Abnormal Leak in Accumulator |
351 |
Does not come on |
Electronically controlled brake system DTC |
|
C1392 |
Zero Point Calibration of Stroke Sensor undone |
1124 |
Only DTC C1392 (INF code 1124) is stored: Does not come on SAE Code C1392 is stored: Comes on |
HINT: During Test Mode, related DTCs are cleared (except SAE code). |
|
C13AF |
EPB System Malfunction |
420 |
Does not come on |
Brake hold DTC HINT: EPB: Electric Parking Brake System |
|
C1401 |
Malfunction in Front Speed Sensor RH Circuit |
501 502 507 |
Comes on |
|
|
C1402 |
Malfunction in Front Speed Sensor LH Circuit |
511 512 517 |
Comes on |
|
|
C1403 |
Malfunction in Rear Speed Sensor RH Circuit |
521 522 527 |
Comes on |
|
|
C1404 |
Malfunction in Rear Speed Sensor LH Circuit |
531 532 537 |
Comes on |
|
|
C1405 |
Open or Short in Front Speed Sensor RH Circuit |
503 506 508 |
Comes on |
|
|
C1406 |
Open or Short in Front Speed Sensor LH Circuit |
513 516 518 |
Comes on |
|
|
C1407 |
Open or Short in Rear Speed Sensor RH Circuit |
523 526 528 |
Comes on |
|
|
C1408 |
Open or Short in Rear Speed Sensor LH Circuit |
533 536 538 |
Comes on |
|
|
C1413 |
Front Speed Sensor RH Circuit Output |
504 541 |
Comes on |
|
|
C1414 |
Front Speed Sensor LH Circuit Output |
514 542 |
Comes on |
|
|
C1415 |
Rear Speed Sensor RH Circuit Output |
524 543 |
Comes on |
|
|
C1416 |
Rear Speed Sensor LH Circuit Output |
534 544 |
Comes on |
|
|
C1417 |
IG1 Voltage Supply too High |
553 |
Comes on |
|
|
C1419 |
Deceleration Sensor Internal Circuit |
1137 |
Comes on |
|
|
C1420 |
Malfunction in Deceleration Sensor |
571 |
Does not come on |
ABS DTC |
|
C1425 |
Open in Stop Switch Circuit |
231 |
Comes on |
|
|
C1427 |
Malfunction in Motor |
1159 |
Comes on |
|
|
C1428 |
Motor Circuit |
611 1160 |
Comes on |
|
|
C1432 |
Steering Angle Sensor Power Source Voltage |
703 |
Does not come on |
VSC DTC |
|
C1433 |
Steering Angle Sensor Internal Circuit |
702 |
Does not come on |
VSC DTC |
|
C1434 |
Steering Angle Sensor Output |
701 |
Does not come on |
VSC DTC |
|
C1435 |
Yaw Rate Sensor Internal Circuit |
711 712 |
Does not come on |
VSC DTC |
|
C1436 |
Malfunction in Yaw Rate Sensor |
713 714 |
Does not come on |
VSC DTC |
|
C1439 |
Steering Angle Sensor Initialization Incomplete |
752 |
Does not come on |
VSC DTC |
|
C1440 |
Steering Angle Sensor Unusual Bank Angle Detected |
1157 |
Does not come on |
VSC DTC |
|
C1442 |
Invalid Data Received from Deceleration Sensor |
572 |
Comes on |
|
|
C1443 |
Invalid Data Received from Yaw Rate Sensor |
715 |
Does not come on |
VSC DTC |
|
C1445 |
Vehicle Driven with Steering Angle Sensor not Initialized |
753 |
Does not come on |
VSC DTC |
|
C1451 |
Motor Drive Permission Malfunction |
1152 |
Only DTC C1451 (INF code 1152) is stored: Does not come on SAE Code C1451 is stored: Comes on |
HINT:
|
|
C146C |
Open Circuit in ABS Motor Relay Circuit |
612 |
Comes on |
|
|
C146D |
Short Circuit in ABS Motor Relay Circuit |
613 |
Comes on |
|
|
C146E |
Open Circuit in ABS Solenoid Relay Circuit |
1135 |
Comes on |
|
|
C146F |
Short Circuit in ABS Solenoid Relay Circuit |
1136 |
Comes on |
|
|
C147D |
Air Bag Circuit |
451 |
Does not come on |
Secondary collision brake DTC HINT: The DTC is cleared when the conditions return to normal. |
|
C14B0 |
Reaction Force Pressure Sensor Power Supply Voltage Malfunction |
201 |
Comes on |
|
|
C14B1 |
Reaction Force Pressure Sensor Communication Malfunction |
202 |
Comes on |
|
|
C14B2 |
Reaction Force Pressure Sensor Internal Malfunction |
203 |
Comes on |
|
|
C14B3 |
Reaction Force Pressure Sensor Zero Point Malfunction |
204 |
Comes on |
|
|
C14B4 |
Reaction Force Pressure Sensor Output Malfunction |
207 |
Comes on |
|
|
C14B5 |
Reaction Force Pressure Sensor Data Invalid |
208 |
Comes on |
|
|
C14B6 |
Stroke Sensor / Reaction Force Pressure Sensor Output Inconsistent |
209 |
Comes on |
|
|
C14C0 |
Servo Pressure Sensor Power Supply Voltage Malfunction |
421 |
Comes on |
|
|
C14C1 |
Servo Pressure Sensor Communication Malfunction |
422 |
Comes on |
|
|
C14C2 |
Servo Pressure Sensor Internal Malfunction |
423 |
Comes on |
|
|
C14C3 |
Servo Pressure Sensor Zero Point Malfunction |
424 |
Comes on |
|
|
C14C4 |
Servo Pressure Sensor Output Malfunction |
426 |
Comes on |
|
|
C14C5 |
Servo Pressure Sensor Data Invalid |
427 |
Comes on |
|
|
C14D0 |
Accumulator Pressure Sensor Power Supply Voltage Malfunction |
331 |
Comes on |
|
|
C14D1 |
Accumulator Pressure Sensor Communication Malfunction |
332 |
Comes on |
|
|
C14D2 |
Accumulator Pressure Sensor Internal Malfunction |
335 |
Comes on |
|
|
C14D3 |
Accumulator Pressure Sensor Output Malfunction |
333 |
Comes on |
|
|
C14D4 |
Accumulator Pressure Sensor Data Invalid |
336 337 |
Comes on |
|
|
C14D5 |
Accumulator Pressure Sensor Stuck |
334 |
Comes on |
|
|
C14DF |
Brake Pressure Control Solenoid Supply Voltage Circuit High |
- |
Comes on |
- |
|
P0573 |
Brake Switch "A" Circuit High |
- |
Comes on |
- |
|
U0073 |
Control Module Communication Bus Off |
461 462 463 |
Comes on |
|
|
U0100 |
Lost Communication With ECM/PCM "A" |
- |
Comes on |
- |
|
U0110 |
Lost Communication with Drive Motor Control Module "A" |
1153 1154 |
Comes on |
|
|
U0120 |
Lost Communication With Starter / Generator Control Module |
1158 |
Comes on |
|
|
U0124 |
Lost Communication With Lateral Acceleration Sensor Module |
591 592 |
Comes on |
|
|
U0126 |
Lost Communication With Steering Angle Sensor Module |
741 742 |
Does not come on |
VSC DTC |
|
U0128 |
Lost Communication With EPB Module |
425 |
Comes on |
HINT: EPB: Electric Parking Brake System |
|
U0151 |
Lost Communication With Restraints Control Module |
450 |
Does not come on |
Secondary collision brake DTC |
|
U0293 |
Lost Communication with Hybrid Vehicle Control System |
411 412 413 |
Comes on |
|

