Open Circuit in ABS Solenoid Relay Circuit (C146E). Air Bag Circuit (C147D). Engine Control System Malfunction (C1201)
Open Circuit in ABS Solenoid Relay Circuit (C146E)
DESCRIPTION
The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly. The ABS solenoid relay supplies power to the ABS and TRAC solenoids. The skid control ECU (brake actuator assembly) detects an ABS solenoid relay malfunction by performing a self check and relay operation check.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C146E |
Open Circuit in ABS Solenoid Relay Circuit |
Either of the following is detected:
|
|
Vehicle Condition |
|||
|---|---|---|---|
Pattern 1 | Pattern 2 |
||
Diagnosis Condition |
- |
- |
- |
Malfunction Status |
The ABS solenoid relay drive circuit in the skid control ECU (brake actuator assembly) is malfunctioning. |
○ |
- |
The ABS solenoid relay cannot be switched between on and off. |
- |
○ |
|
Detection Time |
- |
- |
|
Number of Trips |
1 trip |
1 trip |
|
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
WIRING DIAGRAM
NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
REPLACE BRAKE ACTUATOR ASSEMBLY
(a) Replace the skid control ECU (brake actuator assembly).
Click here ![]()
HINT:
This DTC is output when the skid control ECU (brake actuator assembly) detects a malfunction in an internal circuit.
(b) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Utility / Test Mode.
(c) Perform system variant learning and acceleration sensor zero point calibration.
Click here ![]()
Test Mode
(d) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Utility / Signal Check.
(e) Perform the sensor check using the Test Mode (Signal Check) procedure.
Click here ![]()
Signal Check
| NEXT | END |
Air Bag Circuit (C147D)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives the secondary collision brake control request signal from the airbag sensor assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C147D |
Air Bag Circuit |
An abnormal secondary collision brake control request signal is received 3 times or more when communication with the airbag sensor assembly is possible. |
|
NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here ![]()
PROCEDURE
CHECK DTC (AIRBAG SYSTEM)
(a) Check if airbag system DTCs are output.
Body Electrical > SRS Airbag > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTCs are output |
B |
| A | REPLACE BRAKE ACTUATOR ASSEMBLY |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART (AIRBAG SYSTEM) |
Engine Control System Malfunction (C1201)
DESCRIPTION
If a malfunction in the SFI system is detected, the operation of VSC and TRAC is prohibited by the fail-safe function. When the signals from the engine are received normally, fail-safe control is canceled.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1201 |
Engine Control System Malfunction |
Engine control system malfunction signal continues for 2.5 seconds. |
SFI system |
PROCEDURE
CHECK SFI SYSTEM
(a) Check if SFI system DTCs are output.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTCs are output |
B |
| A | REPLACE ECM |
| B | INSPECT SFI SYSTEM |