Slip Indicator Light Remains ON. System Diagram. Terminals Of Ecu
Slip Indicator Light Remains ON
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.
If the skid control ECU (brake booster with master cylinder assembly) stores a DTC, the slip indicator light comes on in the combination meter assembly.
The slip indicator light blinks during ABS, VSC and/or TRAC operation.
When the system is malfunctioning, the slip indicator light comes on to warn the driver.
Click here ![]()
WIRING DIAGRAM
Refer to Brake Control Warning Light Remains ON.
Click here ![]()
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Check if CAN communication system DTCs are output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs are not output. |
A |
DTCs are output. |
B |
| B | INSPECT CAN COMMUNICATION SYSTEM |
|
CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
(a) Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.
OK:
The connector is securely connected.
| NG | CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY |
|
CHECK AUXILIARY BATTERY
(a) Check the auxiliary battery voltage.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
Auxiliary battery |
Power switch on (IG) |
11 to 14 V |
Auxiliary battery |
Power switch on (READY) |
11 to 15.5 V |
| NG | CHARGE OR REPLACE AUXILIARY BATTERY |
|
READ VALUE USING TECHSTREAM (SLIP INDICATOR LIGHT)
(a) Select the Data List on the Techstream.
Click here ![]()
Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Slip Indicator Light |
Slip indicator light |
ON or OFF |
ON: Indicator light on OFF: Indicator light off |
- |
Slip Indicator Light
(b) Check the Techstream display condition of the slip indicator light.
Result | Proceed to |
|---|---|
ON is displayed. |
A |
OFF is displayed. |
B |
| A | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| B | INSPECT METER / GAUGE SYSTEM |
System Diagram
SYSTEM DIAGRAM
Transmitting ECU (Transmitter) | Receiving ECU | Signal | Communication Method |
|---|---|---|---|
Skid control ECU (Brake booster with master cylinder assembly) |
Power steering ECU (Rack and pinion power steering gear assembly) |
|
CAN communication line |
Main body ECU (Multiplex network body ECU) |
Skid control ECU (Brake booster with master cylinder assembly) |
Driver side seat belt buckle switch signal |
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Hybrid vehicle control ECU |
|
CAN communication line |
Hybrid vehicle control ECU |
Skid control ECU (Brake booster with master cylinder assembly) |
|
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Steering angle sensor |
Steering angle sensor request signal |
CAN communication line |
Steering angle sensor |
Skid control ECU (Brake booster with master cylinder assembly) |
Steering angle sensor signal |
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Yaw rate and acceleration sensor (Airbag ECU assembly) |
Yaw rate and acceleration request signal |
CAN communication line |
Yaw rate and acceleration sensor (Airbag ECU assembly) |
Skid control ECU (Brake booster with master cylinder assembly) |
Yaw rate and acceleration signal |
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Parking brake ECU (Brake actuator assembly) |
|
CAN communication line |
Parking brake ECU (Brake actuator assembly) |
Skid control ECU (Brake booster with master cylinder assembly) |
|
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Combination meter assembly |
|
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Certification ECU (Smart key ECU assembly) |
|
CAN communication line |
Certification ECU (Smart key ECU assembly) |
Skid control ECU (Brake booster with master cylinder assembly) |
Push start switch signal |
CAN communication line |
Skid control ECU (Brake booster with master cylinder assembly) |
Inverter with converter assembly |
|
CAN communication line |
Inverter with converter assembly |
Skid control ECU (Brake booster with master cylinder assembly) |
|
CAN communication line |
Airbag ECU assembly |
Skid control ECU (Brake booster with master cylinder assembly) |
Secondary collision brake request signal |
CAN communication line |
Terminals Of Ecu
TERMINALS OF ECU
TERMINALS OF ECU
*a |
Component without harness connected (Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
- |
- |
Terminal No. (Symbol) | Terminal Description |
|---|---|
1 (MRO1) |
Motor power supply output 1 |
2 (MRI1) |
Motor power supply input 1 |
3 (FR+) |
Front speed sensor RH (+) power supply output |
4 (FR-) |
Front speed sensor RH (-) signal input |
5 (+BI2) |
+BI2 power source input |
6 |
- (Not used) |
7 (RR+) |
Rear speed sensor RH (+) power supply output |
8 (RR-) |
Rear speed sensor RH (-) signal input |
9 (IG2) |
IG2 power source input |
10 |
- (Not used) |
11 (SP1) |
Speed sensor signal output |
12 (STP) |
Stop light switch assembly input |
13 (SKG1) |
Brake pedal stroke sensor assembly ground 1 |
14 (+BS) |
ABS solenoid drive power output |
15 (+BI1) |
+BI1 power source input |
16 (LBL) |
Brake fluid level warning switch (Brake booster with master cylinder assembly) input |
17 (SKS1) |
Brake pedal stroke sensor assembly signal input 1 |
18 (CSW) |
VSC OFF switch input |
19 (SKS2) |
Brake pedal stroke sensor assembly signal input 2 |
20 (CSW2) |
Brake hold switch (Electric parking brake switch assembly) input |
21 (VSK2) |
Brake pedal stroke sensor assembly power supply output 2 |
22 (STPO) |
Stop light control relay (Stop light switch assembly) output |
23 (IG1) |
IG1 power source input |
24 (CTY) |
Front door courtesy light switch assembly LH input |
25 (VSK1) |
Brake pedal stroke sensor assembly power supply output 1 |
26 (GND1) |
Skid control ECU (Brake booster with master cylinder assembly) ground 1 |
27 (MRO2) |
Motor power supply output 2 |
28 (MRI2) |
Motor power supply input 2 |
29 (CA2L) |
CAN communication line 2 (L) |
30 (CA2H) |
CAN communication line 2 (H) |
31 (FL+) |
Front speed sensor LH (+) power supply output |
32 (FL-) |
Front speed sensor LH (-) signal input |
33 (SKG2) |
Brake pedal stroke sensor assembly ground 2 |
34 (RL+) |
Rear speed sensor LH (+) power supply output |
35 (RL-) |
Rear speed sensor LH (-) signal input |
36 |
- (Not used) |
37 (STP2) |
Stop light control relay (Stop light switch assembly) input |
38 |
- (Not used) |
39 (GND2) |
Skid control ECU (Brake booster with master cylinder assembly) ground 2 |
40 (+BM) |
ABS motor drive power output |
41 (BM) |
ABS motor relay power supply input |
42 (CA1L) |
CAN communication line 1 (L) |
43 (CA1H) |
CAN communication line 1 (H) |
44 (SFRR) |
Front ABS reduction solenoid RH (-) output |
45 (SFLR) |
Front ABS reduction solenoid LH (-) output |
46 (SRRR) |
Rear ABS reduction solenoid RH (-) output |
47 (SRLR) |
Rear ABS reduction solenoid LH (-) output |
48 (SFRH) |
Front ABS holding solenoid RH (-) output |
49 (SFLH) |
Front ABS holding solenoid LH (-) output |
50 (SRRH) |
Rear ABS holding solenoid RH (-) output |
51 (SRLH) |
Rear ABS holding solenoid LH (-) output |
52 (BS) |
ABS solenoid relay power supply input |
TERMINAL INSPECTION
(a) Disconnect the connector and measure the voltage or resistance on the wire harness side.
*a |
Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
- |
- |
HINT:
The voltage cannot be measured with the connector connected to the skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.
StandardTerminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A35-2 (MRI1) - Body ground |
B - Body ground |
Motor power supply input 1 |
Always |
11 to 14 V |
A35-5 (+BI2) - Body ground |
BE - Body ground |
+BI2 power source input |
Always |
11 to 14 V |
A35-9 (IG2) - Body ground |
LA-R - Body ground |
IG2 power source input |
Power switch on (IG) |
11 to 14 V |
A35-12 (STP) - Body ground |
SB - Body ground |
Stop light switch assembly input |
Stop light switch assembly on → off (Brake pedal depressed → released) |
11 to 14 V → 1.5 V or less |
A35-15 (+BI1) - Body ground |
SB - Body ground |
+BI1 power source input |
Always |
11 to 14 V |
A35-16 (LBL) - Body ground |
R - Body ground |
Brake fluid level warning switch (Brake booster with master cylinder assembly) input |
Brake fluid level warning switch off → on |
1.84 to 2.16 kΩ → Below 1 Ω |
A35-18 (CSW) - Body ground |
P - Body ground |
VSC OFF switch input |
VSC OFF switch held on → off (Released) |
Below 1 Ω → 10 kΩ or higher |
A35-20 (CSW2) - Body ground |
LG - Body ground |
Brake hold switch (Electric parking brake switch assembly) input |
Brake hold switch (Electric parking brake switch assembly) held on → off (Released) |
Below 1 Ω → 10 kΩ or higher |
A35-22 (STPO) - Body ground |
L - Body ground |
Stop light control relay (Stop light switch assembly) output |
Always |
11 to 14 V |
A35-23 (IG1) - Body ground |
LA-P - Body ground |
IG1 power source input |
Power switch on (IG) |
11 to 14 V |
A35-24 (CTY) - Body ground |
V - Body ground |
Front door courtesy light switch assembly LH input |
Driver door closed → open |
11 to 14 V → 1.5 V or less |
A35-26 (GND1) - Body ground |
LA - Body ground |
Skid control ECU (Brake booster with master cylinder assembly) ground 1 |
Always |
Below 1 Ω |
A35-28 (MRI2) - Body ground |
G - Body ground |
Motor power supply input 2 |
Always |
11 to 14 V |
A35-37 (STP2) - Body ground |
BE - Body ground |
Stop light control relay (Stop light switch assembly) input |
Stop light switch assembly on → off (Brake pedal depressed → released) |
11 to 14 V → 1.5 V or less |
A35-39 (GND2) - Body ground |
W-B - Body ground |
Skid control ECU (Brake booster with master cylinder assembly) ground 2 |
Always |
Below 1 Ω |
A35-41 (BM) - Body ground |
L - Body ground |
ABS motor relay power supply input |
Always |
11 to 14 V |
A35-52 (BS) - Body ground |
LG - Body ground |
ABS solenoid relay power supply input |
Always |
11 to 14 V |