Excessive Brake Pedal Travel (No Fluid Leaks and No Air in System). Fail-safe Chart. Freeze Frame Data
Excessive Brake Pedal Travel (No Fluid Leaks and No Air in System)
NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here ![]()
PROCEDURE
PRE-INSPECTION
(a) Brake pedal inspection
(1) Perform a visual inspection and operate the brake pedal to check for any malfunctions.
(2) Check the brake pedal height, brake pedal free play and brake pedal reserve distance.
Click here ![]()
HINT:
If the brake pedal height is not within specification, confirm that there are no other malfunctions before adjusting the brake pedal height.
(b) Brake inspection
(1) Check that the disc brake pads of each wheel are installed correctly.
(2) Check that the bleeder plug and union bolt is not loose, and that there are no damaged gaskets or brake fluid leaks, for each wheel cylinder.
(c) Brake fluid leaks and air in brake line inspection
(1) Check and take a note of the fluid level in the brake master cylinder reservoir assembly.
(2) Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).
(3) Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.
(4) If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder sub-assembly seals, etc.
(d) Bleeding air from brake system
(1) Bleed air from the brake lines and brake actuator assembly.
Click here ![]()
|
PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Active Test.
Chassis > ABS/VSC/TRAC/EPB > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Motor Relay |
ABS motor relay |
Relay OFF/ON |
Operating sound of motor can be heard |
Motor Relay
(d) Fully depress and hold the brake pedal.
HINT:
Make sure that the brake pedal has travelled excessively before holding it depressed.
(e) Operate the ABS motor relay using the Active Test and check if the brake pedal height changes when the pump motor is operating.
OK:
The brake pedal height does not change (the brake pedal travel remains excessive).
| NG | REPLACE BRAKE ACTUATOR ASSEMBLY |
|
CHECK BRAKE MASTER CYLINDER SUB-ASSEMBLY
(a) Check that there are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.
OK:
There are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.
| NG | REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY |
|
INSPECT BRAKE BOOSTER ASSEMBLY
(a) Inspect operation of the brake booster assembly.
Click here ![]()
OK:
The brake booster assembly is normal.
| OK | USE SIMULATION METHOD TO CHECK |
| NG | REPLACE BRAKE BOOSTER ASSEMBLY |
Fail-safe Chart
FAIL-SAFE CHART
FAIL-SAFE OPERATION
- If there is a problem with sensor signals or actuator systems, the skid control ECU prohibits power supply to the brake actuator assembly and informs the ECM of a VSC system malfunction.
The brake actuator assembly turns off the solenoids and the ECM stops its VSC control according to signals from the skid control ECU. The vehicle will operate in a manner similar to a vehicle that is not equipped with ABS, TRAC, secondary collision brake, VSC and brake hold systems.
ABS control will be prohibited, but EBD control will continue to the extent that EBD control is possible. If EBD control is impossible, the brake system warning light (red indicator) will come on to warn the driver.
Click here

- If a VSC system component malfunctions before VSC control begins, VSC control will be prohibited. If a system component malfunctions during VSC control, the system will gradually stop performing control so as not to trigger a sudden change in vehicle operation.
If it is impossible for control to continue, the warning light comes on to inform the driver of system control termination.
Click here

- If the skid control ECU (brake actuator assembly) detects that a system related to the airbag system or the engine control system is malfunctioning, it will prohibit operation of the secondary collision brake in order to prevent further malfunctions and to protect the systems.
- When a malfunction occurs in the VSC system or electric parking brake system, brake hold control prohibits brake hold operation to prevent incorrect operation and protect the system.
Item | Operation |
|---|---|
Malfunction in the ABS. |
ABS, BA, TRAC and VSC control prohibited. Brake hold control prohibited. |
Malfunction in the BA system. |
ABS, BA, TRAC and VSC control prohibited. Brake hold control prohibited. |
Malfunction in the EBD system. |
ABS, EBD, BA, TRAC and VSC control prohibited. Brake hold control prohibited. |
Item | Operation |
|---|---|
Malfunction in the engine control system (TRAC and VSC systems). |
Before control: Disables control. During control: Uses only the brakes to perform control. |
Malfunction in the brake control system (VSC system). |
Before control: Disables control. During control: Uses only the engine to perform control. |
Malfunction in the brake control system (TRAC system). |
Before control: Disables control. During control: Disables control (by gradually ending control). |
Item | Operation |
|---|---|
Malfunction in the airbag system (secondary collision brake system). |
Before control: Disables control. During control: Uses only the brakes to perform control. |
Malfunction in the engine control system (secondary collision brake system). |
Before control: Disables control. During control: Uses only the brakes to perform control. |
Freeze Frame Data
FREEZE FRAME DATA
FREEZE FRAME DATA
(a) Whenever an ABS DTC is detected, the skid control ECU (brake actuator assembly) stores the current vehicle (ECU or sensor) state as Freeze Frame Data.
(b) The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the engine switch has been turned from off to on (IG) since the last time the ABS was activated.
HINT:
- If the vehicle is stopped or driven at a low speed (7 km/h or less), or if a DTC is detected, the skid control ECU (brake actuator assembly) will stop counting the number.
- Freeze Frame Data at the time the ABS operates:
The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.
When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.
- Freeze Frame Data at the time a DTC is detected:
When the skid control ECU (brake actuator assembly) stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
CHECK FREEZE FRAME DATA
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Trouble Codes.
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes(f) Select a DTC to display its Freeze Frame Data.
Chassis > ABS/VSC/TRAC/EPBTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Elapsed Time after Freeze Trigger |
Elapsed time after freeze trigger |
Min.: 0 msec, Max.: 510 msec |
- |
- |
Number of IG ON |
Number of times engine switch turned on (IG) after Freeze Frame Data stored |
0 to 31 |
- |
- |
Stop Light SW |
Stop light switch assembly |
ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
Parking Brake SW |
Parking brake switch assembly |
ON or OFF |
ON: Parking brake applied OFF: Parking brake released |
- |
Gear Position |
Gear position information |
P/N, R, 1st-10th, Fail or Not R |
Actual gear position |
- |
Shift Lever Position |
Shift lever position information |
P/N, R, D/M, 1st-6th/B or Fail |
Actual shift lever position |
- |
Operated System |
Operated system status |
Non, ABS, VSC, TRAC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC, SCB, Sys |
Actual operated system |
Non: No operation is activated. ABS: ABS is activated. VSC: VSC is activated. TRAC: TRAC is activated. BA: BA is activated. HAB: HAB is activated. Fail: Fail-safe mode is activated. PBA: PBA is activated. PB: PB is activated. HA-CTRL: Hill-start assist control is activated. TSC: Trailer sway control activated* SCB: Secondary collision brake is activated. Sys: System prohibit is activated. HINT: *: Not supported |
Master Cylinder Sensor |
Master cylinder pressure sensor reading |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 0.20 to 0.40 V |
Reading increases when brake pedal is depressed |
M/C Sensor Grade |
Master cylinder pressure sensor change |
Min.: -30 MPa/s, Max.: 225 MPa/s |
Brake pedal released or pedal held at constant position: 0 MPa/s |
When brake pedal is being operated: Changes in proportion with the pedal movement speed |
Yaw Rate Sensor |
Yaw rate sensor |
Min.: -128°/s, Max.: 127°/s |
Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
Lateral G |
Lateral G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
During turning: Changes in proportion with lateral acceleration |
Forward and Rearward G |
Forward and backward G |
Min.: - 25.10 m/s2, Max.: 24.90 m/s2 |
- |
During acceleration/deceleration: Changes in proportion with acceleration |
FR Wheel Speed |
Front wheel speed sensor RH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
FL Wheel Speed |
Front wheel speed sensor LH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
RR Wheel Speed |
Rear wheel speed sensor RH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
RL Wheel Speed |
Rear wheel speed sensor LH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
Vehicle Speed |
Maximum wheel speed sensor reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
Vehicle Speed Grade |
Vehicle speed grade |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
Vehicle stopped: 0 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
Real Engine Torque |
Actual engine torque |
Min.: -1024 Nm, Max.: 1023 N·m |
- |
- |
Accelerator Opening Angle % |
Percentage of accelerator pedal opening angle |
Min.: 0.0%, Max.: 127.5% |
The accelerator pedal released: 0.0% |
During accelerator pedal operation: Changes in proportion with the pedal movement |
Inspection Mode |
Inspection mode |
Other or Inspect |
Other: Normal mode Inspect: Inspection mode |
- |
Steering Angle Sensor |
Steering angle sensor |
Min.: - 3276.8°, Max.: 3276.7° |
Left turn: Increase Right turn: Decrease |
- |
TRAC/VSC Off Mode |
TRAC/VSC off mode |
Normal, TRC OFF, VSC Expert Mode, VSC OFF |
Normal: Normal mode TRC OFF: TRAC off mode VSC Expert Mode: VSC expert mode VSC OFF: VSC off mode |
- |
Brake Hold Ready |
Brake hold control permission status |
OFF or ON |
ON: Brake hold control permitted OFF: Brake hold control not permitted |
- |
Brake Hold Control Mode |
Brake hold control mode |
OFF, ON, Release or EPB |
OFF: Brake hold control is not operating ON: Brake hold control is operating Release: Brake hold control is released EPB: Parking brake is engaged during brake hold control |
HINT: EPB stands for electric parking brake. |
CLEAR FREEZE FRAME DATA
NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data.
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Clear the DTCs and Freeze Frame Data.
Click here ![]()