Open Circuit in IG1/IG2 Power Source Circuit (C1242). Stroke Sensor (C1247,C1392). Brake Booster Pump Motor on Time Abnormally Long (C1252,C1253)
Open Circuit in IG1/IG2 Power Source Circuit (C1242)
DESCRIPTION
Refer to DTC C1241.
Click here ![]()
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1242 |
Open Circuit in IG1/IG2 Power Source Circuit |
111 112 |
|
|
Comes on |
|
MONITOR DESCRIPTION
- During normal operation, the voltage at IG1 and IG2 change mutually; however, if the voltages do not change mutually such as when IG1 is on and IG2 is off or when IG1 is off and IG2 is on, the skid control ECU (brake booster with master cylinder assembly) judges that there is an open in the IG1 or IG2 circuit and illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
C123B: IG1 circuit low C123E: IG2 circuit low |
Required Sensors/Components(Main) |
Skid control ECU (brake booster with master cylinder assembly) |
Required Sensors/Components(Related) |
Speed sensor Skid control ECU (brake booster with master cylinder assembly) |
Frequency of Operation |
Continuous |
Duration |
4 seconds |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
C123BMonitor runs whenever the following DTCs are not stored |
None |
IG2 voltage |
Higher than 9.5 V |
Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
A and B |
A. IG1 voltage |
Higher than 9.5 V |
B. Either of the following condition is met |
- |
Vehicle speed |
Higher than 10 km/h |
Communication status with hybrid control system |
Valid |
TYPICAL MALFUNCTION THRESHOLDS
C123BIG1 |
Off |
IG2 |
Off |
COMPONENT OPERATING RANGE
C123BBoth of the following conditions are met |
- |
IG2 voltage |
Higher than 9.5 V |
IG1 |
On |
Both of the following conditions are met |
- |
IG1 voltage |
Higher than 9.5 V |
IG2 |
On |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (READY).
- Turn the Techstream on.
- Drive the vehicle at 10 km/h or more for 4 seconds or more.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
WIRING DIAGRAM
Refer to DTC C1241.
Click here ![]()
NOTICE:
- After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK FREEZE FRAME DATA
(a) Check the INF code from the Freeze Frame Data stored when DTC (C1242) was stored.
Click here ![]()
Result | Proceed to |
|---|---|
INF code 111 is output. |
A |
INF code 112 is output. |
B |
| B | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (IG1 AND IG2 TERMINAL)
(a) Turn the power switch off. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Turn the power switch on (IG).
(f) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-23 (IG1) - Body ground |
Power switch on (IG) |
11 to 14 V |
A35-9 (IG2) - Body ground |
Power switch on (IG) |
11 to 14 V |
Result | Proceed to |
|---|---|
11 to 14 V. |
A |
Below 11 V. |
B |
| A | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| B | REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 AND/OR IG2 CIRCUIT) |
Stroke Sensor (C1247,C1392)
DESCRIPTION
The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1247 |
Stroke Sensor |
211 212 213 214 215 216 217 |
|
|
Comes on |
|
C1392 |
Zero Point Calibration of Stroke Sensor undone |
1124 |
The brake pedal stroke sensor assembly zero point calibration is not performed. (Normal brake pedal stroke sensor assembly zero point not memorized.) |
Normal brake pedal stroke sensor assembly zero point not memorized. (Linear solenoid valve offset learning is not performed or Test Mode is not performed or not complete.) |
Only DTC C1392 (INF code 1124) is stored: Does not come on SAE Code C1392 is stored: Comes on |
HINT: During Test Mode, related DTCs are cleared (except SAE code). |
MONITOR DESCRIPTION
C0562:- The skid control ECU (brake booster with master cylinder assembly) monitors the power supply voltage of the brake pedal stroke sensor assembly. When the brake pedal stroke sensor assembly power supply voltage is outside of the normal range, the skid control ECU (brake booster with master cylinder assembly) judges that the power supply is abnormal and illuminates the MIL and stores this DTC.
- When the following conditions are met, the skid control ECU (brake booster with master cylinder assembly) judges that the data from the brake pedal stroke sensor assembly is invalid and illuminates the MIL and stores this DTC.
- Brake pedal stroke sensor assembly related DTCs (C0562, P057D, P05DE, P057C, P05DD, P05E0, P057E and P05DF) are not stored.
- When related malfunction DTCs are not stored, the skid control ECU (brake booster with master cylinder assembly) continuously detects a brake pedal stroke sensor assembly malfunction.
- After any of the following situations, if the zero point of the brake pedal stroke sensor 1 or brake pedal stroke sensor 2 has not been learned and the vehicle is being driven at a certain speed or more, the skid control ECU (brake booster with master cylinder assembly) judges that the zero point of the brake pedal stroke sensor is uncalibrated and illuminates the MIL and stores this DTC.
- The skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
- After the brake actuator assembly, brake pedal stroke sensor assembly or brake pedal is removed and installed or replaced, the zero point is cleared.
- The skid control ECU (brake booster with master cylinder assembly) monitors the output value of the brake pedal stroke sensor assembly, and if the following conditions are detected, the skid control ECU (brake booster with master cylinder assembly) judges that the brake pedal stroke sensor assembly has a malfunction and illuminates the MIL and stores a DTC.
- The power supply voltage ratio of the brake pedal stroke sensor 1 and brake pedal stroke sensor 2 is outside the normal range.
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
- When the brake pedal is operated, the relationship between the value output by the brake pedal stroke sensor 1 and brake pedal stroke sensor 2 is outside the normal range.
- The difference between the current power supply voltage ratio and the previous power supply voltage ratio of the brake pedal stroke sensor 1 and brake pedal stroke sensor 2 exceeds a specific value (improbable sudden change repeats).
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
- The power supply voltage ratio of the brake pedal stroke sensor 1 and brake pedal stroke sensor 2 is outside the normal range.
- After any of the following situations, if the zero point of the brake pedal stroke sensor 1 or brake pedal stroke sensor 2 has not been learned, the skid control ECU (brake booster with master cylinder assembly) judges that the zero point of the brake pedal stroke sensor is uncalibrated and illuminates the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights, blinks* the brake hold operated indicator light and stores this DTC.
- The skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
- After the brake actuator assembly, brake pedal stroke sensor assembly or brake pedal is removed and installed or replaced, the zero point is cleared.
HINT:
- *: The brake hold switch (electric parking brake switch assembly) is turned on under the following vehicle conditions.
- Vehicle Conditions:
- The driver side door is closed.
- The driver side seat belt is fastened.
- Vehicle Conditions:
- As the detection conditions slightly differ from SAE code C1392, the detection conditions for DTC C1392 (INF code 1124) is also provided.
- *: The brake hold switch (electric parking brake switch assembly) is turned on under the following vehicle conditions.
MONITOR STRATEGY
HINT:
SAE code only.
Related DTCs |
C0562: Brake pedal stroke sensor assembly voltage circuit/open C124B: Brake pedal stroke sensor assembly invalid data C1392: Brake pedal stroke sensor learning not complete P057C: Brake pedal stroke sensor assembly open circuit P057D: Brake pedal stroke sensor assembly circuit high P057E: Brake pedal stroke sensor assembly intermittent/erratic P05DD: Brake pedal stroke sensor assembly open circuit P05DE: Brake pedal stroke sensor assembly circuit high P05DF: Brake pedal stroke sensor assembly intermittent/erratic P05E0: Brake pedal stroke sensor assembly "1"/"2" correlation |
Required Sensors/Components(Main) |
Brake pedal stroke sensor assembly Skid control ECU (brake booster with master cylinder assembly) |
Required Sensors/Components(Related) |
Skid control ECU (brake booster with master cylinder assembly) Brake pedal stroke sensor assembly Speed sensor |
Frequency of Operation |
Continuous |
Duration |
-: C1392 0.2 seconds: C0562, C124B, P057C, P057D, P057E, P05DD, P05DE, P05DF and P05E0 |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
HINT:
SAE code only.
C0562Monitor runs whenever the following DTCs are not stored |
None |
Brake system voltage 1 (VM1) |
Higher than 6.92 V |
Monitor runs whenever the following DTCs are not stored |
C0562 (Brake pedal stroke sensor assembly voltage circuit/open) P057C, P05DD (Brake pedal stroke sensor assembly open circuit) P057D, P05DE (Brake pedal stroke sensor assembly circuit high) P057E, P05DF (Brake pedal stroke sensor assembly intermittent/erratic) P05E0 (Brake pedal stroke sensor assembly "1"/"2" correlation) |
All of the following conditions are met |
- |
Brake system voltage 1 (VM1) |
Higher than 6.92 V |
Serial communication with high side IC |
Valid |
Brake pedal stroke sensor assembly fail (C0562, P057C, P057D, P057E, P05DD, P05DE, P05DF, P05E0) |
Not detected |
Monitor runs whenever the following DTCs are not stored |
None |
Vehicle speed |
40 km/h or more |
Monitor runs whenever the following DTCs are not stored |
None |
Brake pedal stroke sensor assembly power supply |
4.74 V or more, and 5.23 V or less |
Monitor runs whenever the following DTCs are not stored |
C0562 (Brake pedal stroke sensor assembly voltage circuit/open) C124B (Brake pedal stroke sensor assembly invalid data) P057C, P05DD (Brake pedal stroke sensor assembly open circuit) P057D, P05DE (Brake pedal stroke sensor assembly circuit high) P057E, P05DF (Brake pedal stroke sensor assembly intermittent/erratic) |
Both of the following conditions are met |
- |
Brake system voltage 1 (VM1) |
Higher than 6.92 V |
Brake pedal stroke sensor assembly fail (C0562, C124B, P057C, P057D, P057E, P05DD, P05DE, P05DF) |
Not detected |
TYPICAL MALFUNCTION THRESHOLDS
HINT:
SAE code only.
C0562Brake pedal stroke sensor assembly power supply |
Less than 4.74 V, or higher than 5.23 V |
Brake pedal stroke sensor assembly state |
Invalid |
Either of the following conditions is met |
- |
Brake pedal stroke sensor 1 zero point calibration value |
Not stored |
Brake pedal stroke sensor 2 zero point calibration value |
Not stored |
Power supply voltage ratio of SKS and VSK |
Less than 0.06 |
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
P057D and P05DEPower supply voltage ratio of SKS and VSK |
Higher than 0.94 |
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
P057E and P05DFDifference between the current power supply voltage ratio and the previous power supply voltage ratio of SKS and VSK |
Higher than 8.5% |
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
P05E0Brake pedal stroke sensor assembly correlation state |
Invalid |
COMPONENT OPERATING RANGE
HINT:
SAE code only.
C0562Both of the following conditions are met |
- |
Brake system voltage 1 (VM1) |
Higher than 6.92 V |
Brake pedal stroke sensor assembly power supply |
4.74 V or more, and 5.23 V or less |
Both of the following conditions are met |
- |
Brake system voltage 1 (VM1) |
Higher than 6.92 V |
Brake pedal stroke sensor assembly state |
Valid |
Both of the following conditions are met |
- |
Brake pedal stroke sensor 1 zero point calibration value |
Stored |
Brake pedal stroke sensor 2 zero point calibration value |
Stored |
Both of the following conditions are met |
- |
Brake pedal stroke sensor assembly power supply |
4.74 V or more, and 5.23 V or less |
Power supply voltage ratio of SKS and VSK |
0.06 or more, and 0.94 or less |
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
P057E and P05DFBoth of the following conditions are met |
- |
Brake pedal stroke sensor assembly power supply |
4.74 V or more, and 5.23 V or less |
Difference between the current power supply voltage ratio and the previous power supply voltage ratio of SKS and VSK |
8.5% or less |
HINT:
The power supply voltage ratio is the ratio of the voltage of SKS1 and VSK1 or SKS2 and VSK2.
P05E0Both of the following conditions are met |
- |
Brake system voltage 1 (VM1) |
Higher than 6.92 V |
Brake pedal stroke sensor assembly on experience (low/mid/high) |
On |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (READY).
- Turn the Techstream on.
- Fully depress the brake pedal.
- Drive the vehicle at a speed of 40 km/h or more for 1 minute.
HINT:
Only DTC C1392 is stored when the vehicle speed reaches 40 km/h.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
WIRING DIAGRAM
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
HINT:
Check the condition of each related circuit connector before troubleshooting.
Click here ![]()
PROCEDURE
CHECK BRAKE PEDAL
(a) Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
(b) Check and adjust the brake pedal height.
Click here ![]()
(c) Adjust the brake pedal stroke sensor assembly.
Click here ![]()
|
CHECK DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTC C1247 is output. |
A |
DTC C1392 is output. |
B |
| B | GO TO STEP 7 |
|
CHECK FREEZE FRAME DATA
(a) Check the INF code from the Freeze Frame Data stored when DTC (C1247) was stored.
Click here ![]()
Result | Proceed to |
|---|---|
INF code 211 is output. |
A |
INF code 212, 213, 214, 215, 216 or 217 is output. |
B |
| B | GO TO STEP 6 |
|
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
(a) Turn the power switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(d) Disconnect the A34 brake pedal stroke sensor assembly connector.
(e) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-13 (SKG1) - A34-5 (SKG) |
Always |
Below 1 Ω |
A35-13 (SKG1) or A34-5 (SKG) - Body ground |
Always |
10 kΩ or higher |
A35-21 (VSK2) - A34-2 (VSK2) |
Always |
Below 1 Ω |
A35-21 (VSK2) or A34-2 (VSK2) - Body ground |
Always |
10 kΩ or higher |
A35-25 (VSK1) - A34-4 (VCSK) |
Always |
Below 1 Ω |
A35-25 (VSK1) or A34-4 (VCSK) - Body ground |
Always |
10 kΩ or higher |
A35-33 (SKG2) - A34-3 (SKG2) |
Always |
Below 1 Ω |
A35-33 (SKG2) or A34-3 (SKG2) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
(a) Reconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector. |
|
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A34-4 (VCSK) - A34-5 (SKG) |
Power switch on (IG) |
4.84 to 5.16 V |
A34-2 (VSK2) - A34-3 (SKG2) |
Power switch on (IG) |
4.84 to 5.16 V |
| OK | REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY |
| NG | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
(a) Turn the power switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(d) Disconnect the A34 brake pedal stroke sensor assembly connector.
(e) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-17 (SKS1) - A34-6 (SKS1) |
Always |
Below 1 Ω |
A35-17 (SKS1) or A34-6 (SKS1) - Body ground |
Always |
10 kΩ or higher |
A35-19 (SKS2) - A34-1 (SKS2) |
Always |
Below 1 Ω |
A35-19 (SKS2) or A34-1 (SKS2) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
PERFORM BRAKE PEDAL STROKE SENSOR ASSEMBLY ZERO POINT CALIBRATION
(a) Perform brake pedal stroke sensor assembly zero point calibration.
Click here ![]()
NOTICE:
Make sure to perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization after performing "Reset Memory" as the data stored during linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization is cleared.
Chassis > ABS/VSC/TRAC > UtilityReset Memory
Chassis > ABS/VSC/TRAC > UtilityECB Utility
|
RECONFIRM DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTC C1392 is output. |
A |
DTCs are not output. |
B |
DTCs other than C1392 are output. |
C |
| B | END |
| C | REPAIR CIRCUITS INDICATED BY OUTPUT DTCS |
|
INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
(a) Turn the power switch off. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the A34 brake pedal stroke sensor assembly connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Turn the power switch on (IG).
(f) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A34-4 (VCSK) - A34-5 (SKG) |
Power switch on (IG) |
4.84 to 5.16 V |
A34-2 (VSK2) - A34-3 (SKG2) |
Power switch on (IG) |
4.84 to 5.16 V |
| OK | REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY |
| NG | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
Brake Booster Pump Motor on Time Abnormally Long (C1252,C1253)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1252 |
Brake Booster Pump Motor on Time Abnormally Long |
311 |
The pump motor is operating continuously for 178 seconds or more. (When the relay is malfunctioning for 98 seconds or more.) |
|
Comes on |
|
C1253 |
Pump Motor Relay |
321 322 327 328 |
|
|
Comes on (When only SAE code C121D or SAE code C121E is stored) |
|
MONITOR DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) monitors the voltage of the pump motor.
When the pump motor relay is instructed to be on and the voltage of the pump motor is within the range of an open circuit malfunction (voltage value is practically equal to that when off), or when the pump motor is instructed to be off and the voltage of the pump motor is within the range of a short circuit malfunction (voltage value is practically equal to that when on), an open circuit or short circuit is judged respectively and the MIL is illuminated and stores a DTC.
Furthermore, when the voltage of the pump motor is practically equal to that when on for a long period of time, the skid control ECU (brake booster with master cylinder assembly) judges that the pump motor is operating for an abnormally long time and illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
C0594: Pump motor performance C121D: Pump motor open circuit C121E: Pump motor circuit high |
Required Sensors/Components(Main) |
Brake booster pump assembly |
Required Sensors/Components(Related) |
Skid control ECU (brake booster with master cylinder assembly) Brake booster pump assembly Brake actuator (brake booster with master cylinder assembly) |
Frequency of Operation |
Continuous |
Duration |
0.2 seconds: C121D 2 seconds: C121E 98 seconds: C0594 (Case 1) 178 seconds: C0594 (Case 2) |
MIL Operation |
Immediately |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
C0594 (Case 1)Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
A and B |
A. Serial communication with high side IC |
Valid |
B. One of the following conditions is met |
a, b or c |
a. Pump motor circuit fail (C121D) |
Detected |
b. Pump motor circuit fail (C121E) |
Detected |
c. Both of the following conditions are met |
- |
Accumulator pressure sensor |
Valid |
Accumulator pressure |
Higher than 19.88 MPa (202.7 kgf/cm2, 2884 psi) |
Monitor runs whenever the following DTCs are not stored |
None |
Serial communication with high side IC |
Valid |
Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
A and B |
A. Serial communication with high side IC |
Valid |
B. Either of the following conditions is met |
a or b |
a. Command to pump motor relay |
On |
b. Both of the following conditions are met |
- |
Command to pump motor relay from hardware |
On |
Serial communication with low side IC |
Valid |
Monitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Serial communication with high side IC |
Valid |
Serial communication with low side IC |
Valid |
Command to pump motor relay |
Off |
Command to pump motor relay from hardware |
Off |
TYPICAL MALFUNCTION THRESHOLDS
C0594 (Case 1), C0594 (Case 2) and C121EPump motor voltage |
Higher than 6 V |
Pump motor voltage |
Less than 6 V |
COMPONENT OPERATING RANGE
C0594Both of the following conditions are met |
- |
Prohibit pump motor operating from microcomputer |
Off |
Pump motor voltage |
Less than 6 V |
All of the following conditions are met |
A, B and C |
A. Serial communication with high side IC |
Valid |
B. Either of the following conditions is met |
a or b |
a. Command to pump motor relay |
On |
b. Both of the following conditions are met |
- |
Command to pump motor relay from hardware |
On |
Serial communication with low side IC |
Valid |
C. Pump motor voltage |
Higher than 6 V |
Both of the following conditions are met |
- |
Serial communication with high side IC |
Valid |
Pump motor voltage |
Less than 6 V |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Depress the brake pedal several times until the pump motor operates.
- Wait 3 minutes.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
- Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
- If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here

HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
WIRING DIAGRAM
NOTICE:
- After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK DTC
(a) Check the DTCs that are output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs C1252 and/or C1253 are output. |
A |
DTCs C1241 and/or C1242 are output with DTCs C1252 and/or C1253. |
B |
| B | REPAIR CIRCUITS INDICATED BY OUTPUT DTCS |
|
READ VALUE USING TECHSTREAM (MOTOR RELAY 1 AND MOTOR RELAY 2)
(a) Select the Data List on the Techstream.
Click here ![]()
Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
ECB Motor Relay |
Motor relay 1 operation request |
ON or OFF |
ON: Relay on OFF: Relay off |
ECB: Electronically Controlled Brake System |
ECB Motor Relay2 |
Motor relay 2 operation request |
ON or OFF |
ON: Relay on OFF: Relay off |
ECB: Electronically Controlled Brake System |
Tester Display |
|---|
ECB Motor Relay |
ECB Motor Relay2 |
(b) Depress the brake pedal several times and check the operation status of the motor relay 1 and motor relay 2.
HINT:
Depressing the brake pedal several times drops the accumulator pressure and operates the pump motor.
Result | Proceed to |
|---|---|
The motor relay 1 and motor relay 2 in the Data List turns on or off by depressing the brake pedal several times. |
A |
The status of motor relay 1 and motor relay 2 in the Data List does not change even after depressing the brake pedal several times. |
B |
| B | GO TO STEP 8 |
|
INSPECT BRAKE BOOSTER PUMP ASSEMBLY
(a) Turn the power switch off. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the A40 brake booster pump assembly connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
2 (BM1) - 4 (GND1) |
Always |
10 Ω or less |
1 (BM2) - 3 (GND2) |
Always |
10 Ω or less |
2 (BM1) - 1 (BM2) |
Always |
Below 1 Ω |
4 (GND1) - 3 (GND2) |
Always |
Below 1 Ω |
| NG | REPLACE BRAKE BOOSTER PUMP ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (GND TERMINAL)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT) |
|
READ VALUE USING TECHSTREAM (ACCUMULATOR PRESSURE)
(a) Reconnect the A40 brake booster pump assembly connector.
(b) Disconnect the A34 brake pedal stroke sensor assembly connector.
(c) Select the Data List on the Techstream.
Click here ![]()
Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
MT Voltage Value |
MT voltage value |
Min.: 0.00 V, Max.: 20.00 V |
Pump motor off: 0.00 V Pump motor on: 12.00 V |
- |
Accumulator Pressure |
Accumulator pressure output value |
Min.: 0.00 MPa, Max.: 24.48 MPa |
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) |
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
Tester Display |
|---|
MT Voltage Value |
Accumulator Pressure |
(d) Depress the brake pedal several times to operate the pump motor, then wait until it stops.
(e) After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.
HINT:
- This inspection checks whether an accumulator pressure sensor malfunction, internal brake actuator (brake booster with master cylinder assembly) leak or prolonged operation due to detection of low pressure caused by accumulator deterioration, caused the DTC to be stored.
- If the brake fluid level in the brake master cylinder reservoir assembly (brake booster with master cylinder assembly) drops, an external brake fluid leak is suspected.
Result | Proceed to |
|---|---|
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. |
A |
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. |
B |
| B | GO TO STEP 7 |
|
RECONFIRM DTC
(a) Turn the power switch off.
(b) Reconnect the A34 brake pedal stroke sensor assembly connector.
(c) Clear the DTCs.
Click here ![]()
(d) Turn the power switch off.
(e) Turn the power switch on (IG).
(f) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs C1252 and C1253 are not output. |
A |
DTCs C1252 and/or C1253 are output. |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
READ VALUE USING TECHSTREAM (SERVO PRESSURE)
(a) Turn the power switch off.
(b) Reconnect the A34 brake pedal stroke sensor assembly connector.
(c) Select the Active Test on the Techstream.
Click here ![]()
Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
ECB Solenoid (SLR) |
Linear solenoid reduction valve (SLR) |
Solenoid ON/OFF |
ECB: Electronically Controlled Brake System |
Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Servo Pressure |
Pressure value of servo |
Min.: 0.00 MPa, Max.: 24.48 MPa |
Brake pedal released: 0.00 to 2.10 MPa |
Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
ECB Solenoid (SLR)
Servo Pressure
(d) Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).
(e) Check that the servo pressure output value does not increase when performing the Active Test.
OK:
The servo pressure output value does not increase when performing the Active Test.
HINT:
If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.
Result | Proceed to |
|---|---|
The servo pressure output value increases. |
A |
The servo pressure output value does not increase. |
B |
| A | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| B | REPLACE BRAKE BOOSTER PUMP ASSEMBLY |
CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
(a) Turn the power switch off. |
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-2 (MRI1) - Body ground |
Always |
11 to 14 V |
A35-28 (MRI2) - Body ground |
Always |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT) |
|
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the A40 brake booster pump assembly connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A35-1 (MRO1) - A40-2 (BM1) |
Always |
Below 1 Ω |
A35-1 (MRO1) or A40-2 (BM1) - Body ground |
Always |
10 kΩ or higher |
A35-27 (MRO2) - A40-1 (BM2) |
Always |
Below 1 Ω |
A35-27 (MRO2) or A40-1 (BM2) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |




