Power Supply Drive Circuit (C1257). HV Control System Regenerative Malfunction (C1259,C1310). Abnormal Zero Point of Steering Angle Sensor (C1290)
Power Supply Drive Circuit (C1257)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) detects a drop in accumulator pressure according to the signals from the accumulator pressure sensor, then operates and stops the motor relay as well as the pump motor.
The skid control ECU (brake booster with master cylinder assembly) troubleshoots the built-in motor relay drive circuit, and stores this DTC when a malfunction is detected.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1257 |
Power Supply Drive Circuit |
361 362 |
|
Skid control ECU (brake booster with master cylinder assembly) |
Does not come on |
Electronically controlled brake system DTC |
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
PROCEDURE
CHECK DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTC C1257 is output. |
A |
DTCs C1241, C1242 and/or C1253 are output. |
B |
| A | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| B | REPAIR CIRCUITS INDICATED BY OUTPUT DTCS |
HV Control System Regenerative Malfunction (C1259,C1310)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) communicates with the hybrid vehicle control ECU and controls braking force according to the motor's regenerative force.
The skid control ECU (brake booster with master cylinder assembly) sends enhanced-VSC signals to the hybrid vehicle control ECU and receives operating signals from the hybrid vehicle control ECU.
The skid control ECU (brake booster with master cylinder assembly) uses CAN communication for communicating with the hybrid vehicle control ECU. If a communication malfunction is detected, the skid control ECU (brake booster with master cylinder assembly) prohibits enhanced-VSC operation, brake hold operation and part of the electronically controlled brake system control as a fail-safe function.
If the signals from the hybrid vehicle control ECU return to normal, the warning light will go off and the DTCs C1259 and C1310 will be cleared.
HINT:
These DTCs will be output from the skid control ECU (brake booster with master cylinder assembly) when the hybrid vehicle control ECU sends a malfunction signal to the skid control ECU (brake booster with master cylinder assembly).
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1259 |
HV Control System Regenerative Malfunction |
1132 |
A regeneration malfunction signal is input for at least 0.036 seconds when IG2 terminal voltage is 9.5 V or more for at least 2 seconds and communication with the hybrid vehicle control ECU is valid. |
|
Does not come on |
Electronically controlled brake system DTC HINT: The DTC is cleared when the conditions return to normal. |
C1310 |
HV System Malfunction |
1140 1141 |
|
|
Does not come on |
|
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here ![]()
PROCEDURE
CHECK DTC (HYBRID CONTROL SYSTEM)
(a) Check if a hybrid control system DTCs are output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs are not output. |
A |
DTCs are output. |
B |
| B | INSPECT HYBRID CONTROL SYSTEM |
|
CHECK DTC (MOTOR GENERATOR CONTROL SYSTEM)
(a) Check if a motor generator control system DTCs are output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs are not output. |
A |
DTCs are output. |
B |
| B | INSPECT MOTOR GENERATOR CONTROL SYSTEM |
|
CHECK DTC (SFI SYSTEM)
(a) Check if a SFI system DTCs are output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs are not output. |
A |
DTCs are output. |
B |
| B | INSPECT SFI SYSTEM |
|
RECONFIRM DTC
(a) Clear the DTCs.
Click here ![]()
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Click here ![]()
Result | Proceed to |
|---|---|
DTCs C1259 and/or C1310 are output. |
A |
DTCs other than C1259 and C1310 are output. |
B |
DTCs are not output. |
C |
| A | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| B | REPAIR CIRCUITS INDICATED BY OUTPUT DTCS |
| C | USE SIMULATION METHOD TO CHECK |
Abnormal Zero Point of Steering Angle Sensor (C1290)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) acquires the steering angle sensor zero point every time the power switch on (READY) and the vehicle is driven at 35 km/h or more for approximately 5 seconds. The skid control ECU (brake booster with master cylinder assembly) also stores the previous zero point.
If front wheel alignment or the steering wheel position is adjusted without disconnecting the cable from the negative (-) auxiliary battery terminal, or if the yaw rate and acceleration sensor zero point is not acquired after the adjustments have been completed, the skid control ECU (brake booster with master cylinder assembly) detects the difference between the previous zero point and newly acquired zero point and stores this DTC to indicate a poor adjustment.
Warning operation for the steering angle sensor zero point malfunction will be canceled by turning the power switch off.
DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|---|
C1290 |
Abnormal Zero Point of Steering Angle Sensor |
751 |
The steering angle sensor zero point calibration position vastly differs from the recorded value. |
|
Does not come on |
VSC DTC |
PROCEDURE
PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
(a) Perform zero point calibration of the yaw rate and acceleration sensor.
Click here ![]()
NOTICE:
Make sure to perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization after performing "Reset Memory" as the data stored during linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization is cleared.
Chassis > ABS/VSC/TRAC > UtilityReset Memory
Chassis > ABS/VSC/TRAC > UtilityTest Mode
HINT:
- When the stored zero point of the yaw rate and acceleration sensor is cleared, the steering angle sensor zero point will also be cleared.
- If the zero point and output value of the yaw rate and acceleration sensor and the output value of the speed sensors are not normal, steering angle sensor zero point cannot be acquired normally even if the vehicle is driven straight ahead at 35 km/h or more.
|
CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
(a) Turn the power switch off.
(b) Turn the power switch on (READY).
(c) Drive the vehicle straight ahead at 35 km/h or more for at least 5 seconds.
(d) Check that the centered position of the steering wheel is correctly set while driving straight ahead.
OK:
The steering wheel is centered correctly.
HINT:
If front wheel alignment and steering position are adjusted as a result of the steering wheel being off-center, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.
| OK | END |
| NG | ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION |