ECU Terminals
ECU TERMINALS
NOTICE:
- After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.
Click here
.gif)
- Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
- This section describes the standard values for all components associated with the CAN system.
HINT:
- The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
Click here
.gif)
- Operating the ignition switch, any other switch or a door triggers CAN communication from the corresponding ECU or sensor. This communication changes the resistance value.
- Even after clearing the DTCs, if a DTC is stored again after driving the vehicle for a while, the malfunction may be caused by vehicle vibration. In this case, wiggling the ECUs and wire harnesses during the inspection below may help identify the cause of the problem.
CAN JUNCTION CONNECTOR NO. 1 (without blind spot monitor system)
(a) Check CAN junction connector No. 1.
(1) Connection diagram
*a |
Front view of wire harness side connector (to CAN junction connector No. 1) |
*b |
to forward recognition camera (with Toyota Safety Sense P System) |
*c |
to millimeter wave radar sensor assembly (with Toyota Safety Sense P System) |
*d |
to Central Gateway ECU (Network Gateway ECU) |
(2) Check the wiring diagram of the components connected to CAN junction connector No. 1.
Terminal No. (Symbol) | Wire Color | Connects to |
|---|---|---|
F112-2 (CANH) |
R |
Forward recognition camera*1 (for bus 1) |
F112-13 (CANL) |
GR |
|
F112-3 (CANH) |
G |
Millimeter Wave Radar Sensor Assembly*1 (for bus 1) |
F112-14 (CANL) |
GR |
|
F112-4 (CANH) |
B |
Central Gateway ECU (Network Gateway ECU) (for bus 1) |
F112-15 (CANL) |
GR |
|
F112-5 (CANH) |
P |
Central Gateway ECU (Network Gateway ECU) (for bus 1) |
F112-16 (CANL) |
GR |
- *1: with Toyota Safety Sense P system
CAN JUNCTION CONNECTOR NO. 1 (with blind spot monitor system)
(a) Check CAN junction connector No. 1.
(1) Connection diagram
*a |
Front view of wire harness side connector (to CAN junction connector No. 1) |
*b |
to forward recognition camera (with Toyota Safety Sense P System) |
*c |
to millimeter wave radar sensor assembly (with Toyota Safety Sense P System) |
*d |
to CAN junction connector No. 6 |
*e |
to Central Gateway ECU (Network Gateway ECU) |
- |
- |
(2) Check the wiring diagram of the components connected to CAN junction connector No. 1.
Terminal No. (Symbol) | Wire Color | Connects to |
|---|---|---|
F112-2 (CANH) |
R |
Forward recognition camera*1 (for bus 1) |
F112-13 (CANL) |
GR |
|
F112-3 (CANH) |
G |
Millimeter Wave Radar Sensor Assembly*1 (for bus 1) |
F112-14 (CANL) |
GR |
|
F112-4 (CANH) |
B |
CAN J/C Connector No. 6 (for bus 1) |
F112-15 (CANL) |
GR |
|
F112-5 (CANH) |
P |
Central Gateway ECU (Network Gateway ECU) (for bus 1) |
F112-16 (CANL) |
GR |
- *1: with Toyota Safety Sense P system
CAN J/C CONNECTOR NO. 3
(a) Check CAN junction connector No. 3.
(1) Connection diagram
*a |
Front view of wire harness side connector (to CAN junction connector No. 3) |
*b |
to combination meter assembly |
*c |
to Main Body ECU (Multiplex Network Body ECU) |
*d |
to LH headlight ECU sub-assembly (for LED Headlight) |
*e |
to air conditioning amplifier assembly |
*f |
to certification ECU (smart key system ECU assembly) (with Smart Key System) |
*g |
to Central Gateway ECU (Network Gateway ECU) |
*h |
to DCM (telematics transceiver) (with Telematics Transceiver) |
*i |
to radio and display receiver assembly (for Radio and Display Type) |
- |
- |
(2) Check the wiring diagram of the components connected to CAN junction connector No. 3.
Terminal No. (Symbol) | Wire Color | Connects to |
|---|---|---|
F114-1 (CANH) |
V |
Combination meter assembly (for bus 5) |
F114-12 (CANL) |
SB |
|
F114-2 (CANH) |
G |
Main body ECU (multiplex network body ECU) (for bus 5) |
F114-13 (CANL) |
SB |
|
F114-3 (CANH) |
L |
LH headlight ECU sub-assembly*1 (for bus 5) |
F114-14 (CANL) |
SB |
|
F114-4 (CANH) |
P |
Air Conditioning Amplifier Assembly (for bus 5) |
F114-15 (CANL) |
SB |
|
F114-5 (CANH) |
R |
Certification ECU (smart key system ECU assembly)*2 (for bus 5) |
F114-16 (CANL) |
SB |
|
F114-6 (CANH) |
B |
Central Gateway ECU (Network Gateway ECU) (for bus 5) |
F114-17 (CANL) |
SB |
|
F114-8 (CANH) |
GR |
DCM (telematics transceiver)*3 (for bus 3) |
F114-19 (CANL) |
LG |
|
F114-9 (CANH) |
B |
Radio and display receiver assembly*4 (for bus 3) |
F114-20 (CANL) |
LG |
|
F114-10 (CANH) |
G |
Central Gateway ECU (Network Gateway ECU) (for bus 3) |
F114-21 (CANL) |
LG |
|
F114-11 (CANH) |
V |
Central Gateway ECU (Network Gateway ECU) (for bus 3) |
F114-22 (CANL) |
LG |
- *1: for LED headlight
- *2: with Smart Key System
- *3: with telematics transceiver
- *4: for type with radio and display
CAN J/C CONNECTOR NO. 4
(a) Check CAN junction connector No. 4.
(1) Connection diagram
*a |
Front view of wire harness side connector (to CAN junction connector No. 4) |
*b |
to airbag sensor assembly |
*c |
to steering angle sensor |
*d |
to power steering ECU assembly |
*e |
to CAN junction connector No. 5 |
- |
- |
(2) Check the wiring diagram of the components connected to CAN junction connector No. 4.
Terminal No. (Symbol) | Wire Color | Connects to |
|---|---|---|
F123-1 (CANH) |
B |
Airbag sensor assembly (for bus 4) |
F123-12 (CANL) |
W |
|
F123-5 (CANH) |
BE |
Steering angle sensor (for bus 4) |
F123-16 (CANL) |
W |
|
F123-6 (CANH) |
P |
Power steering ECU assembly (for bus 4) |
F123-17 (CANL) |
W |
|
F123-7 (CANH) |
GR |
CAN Junction Connector No. 5 (for bus 4) |
F123-18 (CANL) |
W |
CAN J/C CONNECTOR NO. 5
(a) Check CAN junction connector No. 5.
(1) Connection diagram
*a |
Front view of wire harness side connector (to CAN junction connector No. 5) |
*b |
to CAN junction connector No. 4 |
*c |
to Central Gateway ECU (Network Gateway ECU) |
*d |
to occupant detection ECU (with Occupant Detection ECU) |
*e |
to brake actuator assembly |
- |
- |
(2) Check the wiring diagram of the components connected to CAN junction connector No. 5.
Terminal No. (Symbol) | Wire Color | Connects to |
|---|---|---|
F124-1 (CANH) |
GR |
CAN Junction Connector No. 4 (for bus 4) |
F124-12 (CANL) |
W |
|
F124-2 (CANH) |
B |
Central Gateway ECU (Network Gateway ECU) (for bus 4) |
F124-13 (CANL) |
W |
|
F124-4 (CANH) |
SB |
Occupant detection ECU*1 (for bus 4) |
F124-15 (CANL) |
W |
|
F124-5 (CANH) |
LG |
Brake Actuator Assembly (for bus 4) |
F124-16 (CANL) |
W |
- *1: with occupant detection ECU
CAN JUNCTION CONNECTOR NO. 6 (with blind spot monitor system)
(a) Check CAN junction connector No. 6.
(1) Connection diagram
*a |
Front view of wire harness side connector (to CAN junction connector No. 6) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
*c |
to LH blind spot sensor |
*d |
to CAN junction connector No. 1 |
(2) Check the wiring diagram of the components connected to CAN junction connector No. 6.
Terminal No. (Symbol) | Wire Color | Connects to |
|---|---|---|
M92-1 (CANH) |
R |
Central Gateway ECU (Network Gateway ECU) (for bus 1) |
M92-12 (CANL) |
GR |
|
M92-6 (CANH) |
G |
Left blind spot monitor sensor (for bus 1) |
M92-17 (CANL) |
GR |
|
M92-11 (CANH) |
B |
CAN J/C Connector No. 1 (for bus 1) |
M92-22 (CANL) |
GR |
DLC3
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F41-6 (CANH) - F41-14 (CANL) |
R - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F41-6 (CANH) - F41-4 (CG) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F41-14 (CANL) - F41-4 (CG) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F41-6 (CANH) - F41-16 (BAT) |
R - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F41-14 (CANL) - F41-16 (BAT) |
W - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
*a |
Component without wire harness connected (central gateway ECU (network gateway ECU)) |
- |
- |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector F74 of central gateway ECU (network gateway ECU).
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness side connector (to central gateway ECU (network gateway ECU)) |
- |
- |
Standard resistance:
Diagnosis bus secondary lines (DLC3 - Central Gateway ECU (Network Gateway ECU))Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F74-14 (CA6H) - F74-5 (CA6L) |
R - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
1 MΩ or higher |
F74-14 (CA6H) - F74-10 (GND) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-5 (CA6L) - F74-10 (GND) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-14 (CA6H) - F74-1 (BATT) |
R - Y |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F74-5 (CA6L) - F74-1 (BATT) |
W - Y |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F74-23 (CA1H) - F74-9 (CAXH) |
R - P |
CAN bus HIGH line - CAN bus HIGH line |
Cable disconnected from negative (-) battery terminal |
Below 1 Ω |
F74-8 (CA1L) - F74-24 (CAXL) |
GR - GR |
CAN bus LOW line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
Below 1 Ω |
F74-23 (CA1H) - F74-10 (GND) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-8 (CA1L) - F74-10 (GND) |
GR - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-23 (CA1H) - F74-1 (BATT) |
R - Y |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F74-8 (CA1L) - F74-1 (BATT) |
GR - Y |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F74-18 (CA4H) - F74-17 (CA4L) |
R - P |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
108 à 132 Ω |
F74-18 (CA4H) - F74-10 (GND) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-17 (CA4L) - F74-10 (GND) |
P - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-18 (CA4H) - F74-1 (BATT) |
R - Y |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F74-17 (CA4L) - F74-1 (BATT) |
P - Y |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F74-22 (CA2H) - F74-7 (CA2L) |
B - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
108 à 132 Ω |
F74-22 (CA2H) - F74-10 (GND) |
B - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-7 (CA2L) - F74-10 (GND) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-22 (CA2H) - F74-1 (BATT) |
B - Y |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F74-7 (CA2L) - F74-1 (BATT) |
W - Y |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F74-15 (CA5H) - F74-16 (CA5L) |
B - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
108 à 132 Ω |
F74-15 (CA5H) - F74-10 (GND) |
B - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-16 (CA5L) - F74-10 (GND) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F74-15 (CA5H) - F74-1 (BATT) |
B - Y |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F74-16 (CA5L) - F74-1 (BATT) |
SB - Y |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
STEERING ANGLE SENSOR
*a |
Component without wire harness connected (Steering Angle Sensor) |
- |
- |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector F69 from the steering angle sensor.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness side connector (to steering angle sensor) |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F69-3 (CANH) - F69-2 (CANL) |
BE - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F69-3 (CANH) - F69-1 (ESS) |
BE - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F69-2 (CANL) - F69-1 (ESS) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F69-3 (CANH) - F69-5 (BAT) |
BE - P |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F69-2 (CANL) - F69-5 (BAT) |
W - P |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
ECM
Refer to the procedure for the ECU terminals.
- with fuel vapor pump module: Click here
.gif)
- without fuel vapor pump module: Click here
.gif)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connectors A38 and C63 from the ECM.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness side connector (to ECM) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A38-13 (CANH) - A38-26 (CANL) |
R - P |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
108 à 132 Ω |
A38-13 (CANH) - C63-59 (E1) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A38-26 (CANL) - C63-59 (E1) |
P - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A38-13 (CANH) - A38-1 (BATT) |
R - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
A38-26 (CANL) - A38-1 (BATT) |
P - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the combination meter assembly connector F4.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness side connector (to instrument cluster assembly) |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F4-32 (CANH) - F4-31 (CANL) |
V - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
108 à 132 Ω |
F4-32 (CANH) - F4-21 (ET) |
V - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F4-31 (CANL) - F4-21 (ET) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F4-32 (CANH) - F4-40 (B) |
V - SB |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F4-31 (CANL) - F4-40 (B) |
SB - SB |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector A42 from the brake actuator assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A42-5 (CANH) - A42-19 (CANL) |
LG - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
A42-5 (CANH) - A42-46 (GND1) |
LG - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A42-19 (CANL) - A42-46 (GND1) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A42-5 (CANH) - A42-30 (+BS) |
LG - W |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
A42-19 (CANL) - A42-30 (+BS) |
W - W |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness side connector (to brake actuator assembly) |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the F15 connector from the main body ECU (multiplex network body ECU).
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to main body ECU (multiplex network body ECU)) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F15-14 (CANH) - F15-13 (CANL) |
G - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F15-14 (CANH) - F41-4 (CG) |
G - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F15-13 (CANL) - F41-4 (CG) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F15-14 (CANH) - F41-16 (BAT) |
G - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F15-13 (CANL) - F41-16 (BAT) |
SB - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (with Smart Key System)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector F1 from the certification ECU (smart key ECU assembly).
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F1-1 (CANH) - F1-2 (CANL) |
R - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F1-1 (CANH) - F1-18 (E) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F1-2 (CANL) - F1-18 (E) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F1-1 (CANH) - F1-4 (+B) |
R - L |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F1-2 (CANL) - F1-4 (+B) |
SB - L |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness side connector (to certification ECU (smart key ECU assembly)) |
POWER STEERING ECU ASSEMBLY
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connectors F23 and F68 from the power steering ECU assembly.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness side connector (to EPS ECU assembly) |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F23-7 (CANH) - F23-8 (CANL) |
P - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F23-7 (CANH) - F68-2 (PGND) |
P - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F23-8 (CANL) - F68-2 (PGND) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F23-7 (CANH) - F68-1 (PIG) |
P - B-W |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F23-8 (CANL) - F68-1 (PIG) |
W - B-W |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector F70 from the airbag sensor assembly.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to airbag sensor assembly) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F70-13 (CANH) - F70-22 (CANL) |
B - W |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
108 à 132 Ω |
F70-13 (CANH) - F70-25 (E1) |
B - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F70-22 (CANL) - F70-25 (E1) |
W - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F70-13 (CANH) - F41-16 (BAT) |
B - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F70-22 (CANL) - F41-16 (BAT) |
W - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (with A/C pressure sensor mounted on top)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the F72 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F72-9 (CANH) - F72-10 (CANL) |
P - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F72-9 (CANH) - F72-29 (GND) |
P - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F72-10 (CANL) - F72-29 (GND) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F72-9 (CANH) - F72-1 (B) |
P - V |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F72-10 (CANL) - F72-1 (B) |
SB - V |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness side connector (to A/C amplifier assembly) |
AIR CONDITIONING AMPLIFIER ASSEMBLY (with A/C pressure sensor mounted on side)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector F139 from the air conditioning amplifier assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F139-11 (CANH) - F139-12 (CANL) |
P - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F139-11 (CANH) - F139-4 (GND) |
P - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F139-12 (CANL) - F139-4 (GND) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F139-11 (CANH) - F139-1 (B) |
P - V |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F139-12 (CANL) - F139-1 (B) |
SB - V |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness side connector (to A/C amplifier assembly) |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for radio and display type)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connectors F129 and F131 from the radio receiver and display assembly.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness side connector (to radio receiver and display assembly) |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F131-13 (CANH) - F131-14 (CANL) |
B - LG |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F131-13 (CANH) - F129-1 (GND1) |
B - LA |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F131-14 (CANL) - F129-1 (GND1) |
LG - LA |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F131-13 (CANH) - F129-4 (+B1) |
B - LA-SB |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F131-14 (CANL) - F129-4 (+B1) |
LG - LA-SB |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
LEFT HEADLIGHT ECU SUB-ASSEMBLY (for LED headlights)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector A16 from the left headlight ECU sub-assembly.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to left headlight ECU sub-assembly) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A16-24 (CANH) - A16-23 (CANL) |
L - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
A16-24 (CANH) - A16-12 (GND) |
L - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A16-23 (CANL) - A16-12 (GND) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A16-24 (CANH) - F41-16 (BAT) |
L - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
A16-23 (CANL) - F41-16 (BAT) |
SB - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
LEFT BLIND SPOT SENSOR (with blind spot monitor system)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector M62 from the left blind spot sensor.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to left blind spot sensor) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
M62-2 (CA1P) - M62-7 (CA1N) |
G - GR |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
M62-2 (CA1P) - M62-10 (BLGD) |
G - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
M62-7 (CA1N) - M62-10 (BLGD) |
GR - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
M62-2 (CA1P) - F41-16 (BAT) |
G - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
M62-7 (CA1N) - F41-16 (BAT) |
GR - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
FORWARD RECOGNITION CAMERA (with Toyota Safety Sense P)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the front view camera R5 connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to forward recognition camera) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
R5-5 (CA1P) - R5-11 (CA1N) |
R - GR |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
R5-5 (CA1P) - R5-10 (GND) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
R5-11 (CA1N) - R5-10 (GND) |
GR - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
R5-5 (CA1P) - F41-16 (BAT) |
R - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
R5-11 (CA1N) - F41-16 (BAT) |
GR - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (with Toyota Safety Sense P)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector A2 from the millimeter wave radar sensor assembly.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to millimeter wave radar sensor assembly) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A2-3 (CA2H) - A2-2 (CA2L) |
G - GR |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
A2-3 (CA2H) - A2-1 (SGND) |
G - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A2-2 (CA2L) - A2-1 (SGND) |
GR - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
A2-3 (CA2H) - F41-16 (BAT) |
G - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
A2-2 (CA2L) - F41-16 (BAT) |
GR - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
OCCUPANT DETECTION ECU (with occupant detection ECU)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect connector Y6 from the occupant detection ECU.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness side connector (to occupant detection ECU) |
- |
- |
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
Y6-5 (CANH) - Y6-4 (CANL) |
R - SB |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
Y6-5 (CANH) - Y6-10 (GND) |
R - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
Y6-4 (CANL) - Y6-10 (GND) |
SB - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
Y6-5 (CANH) - F41-16 (BAT) |
R - R |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Y6-4 (CANL) - F41-16 (BAT) |
SB - R |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
DCM (TELEMATICS TRANSCEIVER) (with telematics transceiver)
Refer to the procedure for the ECU terminals.
Click here![]()
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the F134 DCM (telematics transceiver) connector.
*a |
Front view of wire harness side connector (to DCM (telematics transceiver)) |
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F134-15 (CANP) - F134-16 (CANN) |
GR - LG |
CAN bus HIGH line - CAN bus LOW line |
Cable disconnected from negative (-) battery terminal |
54 à 69 Ω |
F134-15 (CANP) - F134-4 (E) |
GR - W-B |
CAN bus HIGH line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F134-16 (CANN) - F134-4 (E) |
LG - W-B |
CAN bus LOW line - Ground |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
F134-15 (CANP) - F134-1 (+B) |
GR - W |
CAN bus HIGH line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
F134-16 (CANN) - F134-1 (+B) |
LG - W |
CAN bus LOW line - Battery positive (+) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |