Network Operation

Check for Possible Short Circuit in Bus Line 2

~4min read

DESCRIPTION

There may be a short circuit between the main CAN bus lines and/or between the CAN sub bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the Central Access Gateway ECU (Network Access Gateway ECU) is less than 54 Ω.

Symptom

Suspected Area

The resistance between terminals 18 (CA4H) and 17 (CA4L) of the Central Access Gateway ECU (Network Access Gateway ECU) is less than 54 Ω.

  • Short circuit in main CAN bus lines
  • Short circuit in sub CAN bus lines
  • Central Gateway ECU (Network Gateway ECU)
  • ECM

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.

    DTC check procedure: Turn the blind spot monitor system ON using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch ON, turn the LDA main switch ON, then drive the vehicle at a speed of approximately 60 km/h for approximately 5 minutes.

  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Before replacing the ECM, refer to the registration section.*1

    Click here

  • *1: with Smart Key System

HINT:

  • Before disconnecting the related connectors for inspection, press on the body of each connector to make sure the connector is not loose or disconnected.
  • When a connector is disconnected, make sure the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CENTRAL ACCESS GATEWAY ECU (NETWORK ACCESS GATEWAY ECU))

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the Central Access Gateway ECU (Network Access Gateway ECU).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F74-18 (CA4H) - F74-17 (CA4L)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

ECM

*a

Front view of wire harness side connector

(to central gateway ECU (network gateway ECU))

*b

to ECM

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG
  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (ECM - CENTRAL ACCESS GATEWAY ECU (NETWORK ACCESS GATEWAY ECU))

(a) Disconnect ECM connector A38.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F74-18 (CA4H) - F74-17 (CA4L)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to central gateway ECU (network gateway ECU))

*b

to ECM

OK

REPLACE ECM

NG

REPAIR OR REPLACE MAIN CAN BUS LINES OR CONNECTOR (ECM - CENTRAL ACCESS GATEWAY ECU (NETWORK ACCESS GATEWAY ECU))