Network Operation

Check for possible short circuit in bus lines 3

~6min read

DESCRIPTION

There may be a short circuit between the main CAN bus lines and/or between the secondary CAN lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is less than 54 Ω.

Symptom

Suspected Area

The resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 54 Ω or more.

  • Short circuit in main CAN bus lines
  • Short circuit in sub CAN bus lines
  • Radio and Display Receiver Assembly

    (for Radio and Display Type)

  • DCM (Telematics Transceiver)

    (with Telematics Transceiver)

  • Central Gateway ECU (Network Gateway ECU)
  • CAN Junction Connector No. 3

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.

    DTC Check Procedure: Turn the ignition switch ON and wait for approximately 60 seconds or more.

  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

HINT:

  • Before disconnecting the related connectors for inspection, press on the body of each connector to make sure the connector is not loose or disconnected.
  • When a connector is disconnected, make sure the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CAN JUNCTION CONNECTOR NO. 3)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the CAN junction connector No. 3.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness side connector

(to CAN junction connector No. 3)

*b

to DCM (telematics transceiver)

(with Telematics Transceiver)

*c

to radio and display receiver assembly

(for Radio and Display Type)

*d

to Central Gateway ECU (Network Gateway ECU)

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F114-8 (CANH) - F114-19 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

DCM (Data Communication Module)*1

F114-9 (CANH) - F114-20 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Radio and Display Receiver Assembly*2

F114-10 (CANH) - F114-21 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

F114-11 (CANH) - F114-22 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

  • *1: with telematics transceiver
  • *2: for radio and display type

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (Line to ECU or Sensor)

C

A

REPLACE CAN JUNCTION CONNECTOR NO. 3

C

GO TO STEP 3

B
  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CAN JUNCTION CONNECTOR NO. 3 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F114-10 (CANH) - F114-21 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

F114-11 (CANH) - F114-22 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to CAN junction connector No. 3)

*b

to Central Gateway ECU (Network Gateway ECU)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE MAIN CAN BUS LINES OR CONNECTOR (CAN JUNCTION CONNECTOR NO. 3 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector containing the CANH and CANL terminals of the ECU or sensor to which the shorted sub bus line is connected.

Click here

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F74-6 (CA3H) - F74-21 (CA3L)

Cable disconnected from negative (-) battery terminal

54 à 69 Ω

HINT:

  • If the resistance returns to normal (54 to 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short circuit in the ECU or sensor.
  • If the resistance does not return to normal when the connector is disconnected from the ECU or sensor, check the wire harness for a short circuit and repair or replace the wire harness or connector as necessary.

*a

Component with Wire Harness Connected

(central gateway ECU (network gateway ECU))

OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR