Network Operation

DCM communication stop mode

~4min read

DESCRIPTION

Detection Item

Symptom

Suspected Area

DCM communication stop mode

One or more of the following conditions are met:

  • The communication stop for "DCM" is displayed on the "Communication Bus Check" screen of the Techstream.

    Click here

  • The communication stop history for "DCM" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "DCM" is 6 or more.)

    Click here

  • DTCs of the communication system (DTCs starting with U) corresponding to "DCM Communication Stop Mode" in the "DTC Chart" are output.

    Click here

  • Sub wire or connector of telematics transceiver
  • Power source circuit of telematics transceiver
  • Ground circuit of telematics transceiver
  • Telematics Transceiver

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.
  • DTC check procedure: Turn the ignition switch ON and wait at least approximately 20 seconds.
  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

HINT:

  • Operating the ignition switch, any other switch or a door triggers CAN communication from the corresponding ECU or sensor. This communication changes the resistance value.
  • Even after clearing the DTCs, if a DTC is stored again after driving the vehicle for a while, the malfunction may be caused by vehicle vibration. In this case, wiggling the ECUs and wire harnesses during the inspection below may help identify the cause of the problem.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER SUB WIRE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the connector from the telematics transceiver.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-15 (CANP) - F134-16 (CANN)

Cable disconnected from negative (-) battery terminal

54 à 69 Ω

*a

Front view of wire harness side connector

(to Telematics Transceiver)

NG

REPAIR OR REPLACE CAN SUB WIRES OR CONNECTOR (TELEMATICS TRANSCEIVER)

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-4 (E) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness side connector

(to Telematics Transceiver)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F134-1 (+B) - Body Ground

Always

11 à 14 V

F134-7 (IG2) - Body ground

Ignition Switch in ON position

11 à 14 V

F134-8 (ACC) - Body Ground

Ignition Switch in ACC position

11 à 14 V

OK

REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)