Network Operation

Symptom Table

~16min read

SYMPTOM TROUBLESHOOTING TABLE

HINT:

  • Use the table below to determine the cause of the problem symptoms.
  • Check the fuses and relays associated with this system before checking the suspected areas listed below.
  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

List of Results from "How to Proceed with Troubleshooting"

Symptom

Suspected Area

Link

This is one of the following cases:

  • The problem symptom is that of example B of the problem symptom, and the suspected area is in bus 1.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 1 is 70 Ω or more.

Open circuit in one side of the main bus line of bus 1

This is one of the following cases:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit between the CAN bus lines (CANH and CANL) in bus 1 is suspected.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 1 is less than 54 Ω.

Short circuit in the bus 1 lines

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to +B in a CAN bus line (CANH or CANL) of bus 1 is suspected.
  • The resistance between CANH and +B of bus 1 is less than 6 kΩ.
  • The resistance between CANL and +B of bus 1 is less than 6 kΩ.

Short to +B in the bus 1 line

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to ground in a CAN bus line (CANH or CANL) of bus 1 is suspected.
  • The resistance between CANH and ground of bus 1 is less than 200 Ω.
  • The resistance between CANL and ground of bus 1 is less than 200 Ω.

Short to GND in the bus 1 line

The resistance between CANH and CANL of bus 1 is normal, and the problem symptom example in the section How to Use the "Communication Bus Check" Screen when checking matches the symptoms when there is an open circuit in a wire of the bus 1 branch line.

Open circuit in one side of the branch bus line of bus 1

This is one of the following cases:

  • The problem symptom is that of example B of the problem symptom, and the suspected area is in bus 2.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 2 is 70 Ω or more.

Open circuit in one side of the main bus line of bus 2

This is one of the following cases:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit between the CAN bus lines (CANH and CANL) in bus 2 is suspected.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 2 is less than 54 Ω.

Short circuit in the bus 2 lines

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to +B in a CAN bus line (CANH or CANL) of bus 2 is suspected.
  • The resistance between CANH and +B of bus 2 is less than 6 kΩ.
  • The resistance between CANL and +B of bus 2 is less than 6 kΩ.

Short to +B in the bus 2 line

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to ground in a CAN bus line (CANH or CANL) of bus 2 is suspected.
  • The resistance between CANH and ground of bus 2 is less than 200 Ω.
  • The resistance between CANL and ground of bus 2 is less than 200 Ω.

Short to GND in the bus 2 line

This is one of the following cases:

  • The problem symptom is that of example B of the problem symptom, and the suspected area is in bus 3.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 3 is 70 Ω or more.

Open circuit in one side of the main bus line of bus 3

This is one of the following cases:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit between the CAN bus lines (CANH and CANL) in bus 3 is suspected.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 3 is less than 54 Ω.

Short circuit in the bus 3 lines

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to +B in a CAN bus line (CANH or CANL) of bus 3 is suspected.
  • The resistance between CANH and +B of bus 3 is less than 6 kΩ.
  • The resistance between CANL and +B of bus 3 is less than 6 kΩ.

Short to +B in the bus 3 line

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to ground in a CAN bus line (CANH or CANL) of bus 3 is suspected.
  • The resistance between CANH and ground of bus 3 is less than 200 Ω.
  • The resistance between CANL and ground of bus 3 is less than 200 Ω.

Short to GND in the bus 3 line

The resistance between CANH and CANL of bus 3 is normal, and the problem symptom example in the section How to Use the "Communication Bus Check" Screen when checking matches the symptoms when there is an open circuit in a wire of the bus 3 branch line.

Open circuit in one side of the branch bus line of bus 3

This is one of the following cases:

  • The problem symptom is that of example B of the problem symptom, and the suspected area is in bus 4.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 4 is 70 Ω or more.

Open circuit in one side of the main bus line of bus 4

This is one of the following cases:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit between the CAN bus lines (CANH and CANL) in bus 4 is suspected.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 4 is less than 54 Ω.

Short circuit in the bus 4 lines

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to +B in a CAN bus line (CANH or CANL) of bus 4 is suspected.
  • The resistance between CANH and +B of bus 4 is less than 6 kΩ.
  • The resistance between CANL and +B of bus 4 is less than 6 kΩ.

Short to +B in the bus 4 line

One of the following:

  • The problem symptom is similar to that of example A of the problem symptom, and a short circuit to ground in a CAN bus line (CANH or CANL) of bus 4 is suspected.
  • The resistance between CANH and ground of bus 4 is less than 200 Ω.
  • The resistance between CANL and ground of bus 4 is less than 200 Ω.

Short to GND in the bus 4 line

The resistance between CANH and CANL is normal for bus 4, and the example of the malfunction symptom in the "How to Use the Communication Bus Check Screen" section during inspection matches the symptoms when there is a open circuit in a cable of a bus 4 branch line.

Open circuit in one side of bus 4 branch line

This is one of the following cases:

  • The malfunction symptom is that of Example B of the malfunction symptom, and the suspected area is in bus 5.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 5 is 70 Ω or more.

Open circuit in one side of bus 5 main bus line

This is one of the following cases:

  • The malfunction symptom is similar to that of Example A of the malfunction symptom, and a short circuit between the CAN bus lines (CANH and CANL) in bus 5 is suspected.
  • The resistance between the CAN bus lines (CANH and CANL) of bus 5 is less than 54 Ω.

Short circuit in bus 5 lines

One of the following:

  • The malfunction symptom is similar to that of Example A of the malfunction symptom, and a short circuit to +B in a CAN bus line (CANH or CANL) of bus 5 is suspected.
  • The resistance between CANH and +B of bus 5 is less than 6 kΩ.
  • The resistance between CANL and +B of bus 5 is less than 6 kΩ.

Short circuit to +B in bus 5 line

One of the following:

  • The malfunction symptom is similar to that of Example A of the malfunction symptom, and a short circuit to ground in a CAN bus line (CANH or CANL) of bus 5 is suspected.
  • The resistance between CANH and ground of bus 5 is less than 200 Ω.
  • The resistance between CANL and ground of bus 5 is less than 200 Ω.

Short circuit to GND in bus 5 line

The resistance between CANH and CANL is normal for bus 5, and the example of the malfunction symptom in the "How to Use the Communication Bus Check Screen" section during inspection matches the symptoms when there is an open circuit in a cable of a bus 5 branch line.

Open circuit in one side of bus 5 branch line

HINT:

The suspected communication stop area can be determined from the ECUs or sensors that are displayed as not communicating on the "Communication Bus Check" screen or the "Communication Bus Check (Detail)" screen, by referring to the following table.

Communication Stop Mode Table (open in bus line or other communication stop)

Symptom

Suspected Area

Link

One of the following conditions is met:

  • The communication stop for "Skid Control (ABS/VSC/TRAC)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Skid Control (ABS/VSC/TRAC)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Skid Control (ABS/VSC/TRAC)" is 6 or more.)

Communication stop mode of the skid control ECU

One of the following conditions is met:

  • The communication stop for "Air Conditioning Amplifier" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Air Conditioning Amplifier" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Air Conditioning Amplifier" is 6 or more.)

Communication stop mode of the air conditioning amplifier

One of the following conditions is met:

  • The communication stop for "Power Steering (EPS)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Power Steering (EPS)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Power Steering (EPS)" is 6 or more.)

Communication stop mode of the power steering ECU

One of the following conditions is met:

  • The communication stop for "Spiral Cable (Steering Angle Sensor)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Spiral Cable (Steering Angle Sensor)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Spiral Cable (Steering Angle Sensor)" is 6 or more.)

Communication stop mode of the steering angle sensor

One of the following conditions is met:

  • The communication stop for "ECM (Engine)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "ECM (Engine)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "ECM (Engine)" is 6 or more.)

Communication stop mode of the ECM

One of the following conditions is met:

  • The communication stop for "Main Body" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Main Body" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Main Body" is 6 or more.)

Communication stop mode of the main body ECU

One of the following conditions is met:

  • The communication stop for "Combination Meter" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Combination Meter" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Combination Meter" is 6 or more.)

Communication stop mode of the combination meter ECU

One of the following conditions is met:

  • The communication stop for "Certification (Smart)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Certification (Smart)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Certification (Smart)" is 6 or more.)

Communication stop mode of the certification ECU

One of the following conditions is met:

  • The communication stop for "Airbag" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Airbag" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Airbag" is 6 or more.)

Communication stop mode of the airbag central sensor

One of the following conditions is met:

  • The communication stop for "Headlight Swivel (AFS)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Headlight swivel (AFS)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Headlight swivel (AFS)" is 6 or more.)

Headlight ECU communication stop mode

One of the following conditions is met:

  • The communication stop for "Display and Navigation (AVN)" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Display and Navigation (AVN)" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Display and Navigation (AVN)" is 6 or more.)

Radio receiver assembly communication stop mode

One of the following conditions is met:

  • The communication stop for "Blind Spot Monitor Master" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Blind Spot Monitor Master" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Blind Spot Monitor Master" is 6 or more.)

Blind spot monitor sensor communication stop mode

One of the following conditions is met:

  • The communication stop for "DCM" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "DCM" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "DCM" is 6 or more.)

DCM communication stop mode

One of the following conditions is met:

  • The communication stop for "Front Radar" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Front Radar" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Front Radar" is 6 or more.)

Millimeter wave radar sensor communication stop mode

One of the following conditions is met:

  • The communication stop for "Front Camera Module" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Front Camera Module" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Front Camera Module" is 6 or more.)

Front camera module communication stop mode

One of the following conditions is met:

  • The communication stop for "Occupant Detection" is displayed on the "Communication Bus Check" screen of the Techstream.
  • The communication stop history for "Occupant Detection" is displayed on the "Communication Bus Check (Detail)" screen of the Techstream. (The lost communication duration value for "Occupant Detection" is 6 or more.)

Occupant classification system module communication stop mode limit

DTC Combination Table (open in Bus 1, Bus 2, Bus 4 or Bus 5)

Symptom

Suspected Area

Link

Although CAN communication is currently normal, an ECU connected to the CAN communication system has CAN communication DTCs.

The likely faulty part where communication is interrupted can be identified by using the DTC combination table and comparing the DTCs output from the ECUs connected to the CAN communication system.