Network Operation

Check for a possible short circuit in the bus 1 lines

~12min read

DESCRIPTION

There may be a short circuit between the main CAN bus lines and/or between the sub CAN bus lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is less than 54 Ω.

Symptom

Suspected Area

The resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is at least 54 Ω.

  • Short circuit in main CAN bus lines
  • Short circuit in sub CAN bus lines
  • Central Gateway ECU (Network Gateway ECU)
  • Millimeter wave radar sensor assembly

    (with Toyota Safety Sense P System)

  • Front Area Recognition Camera

    (with Toyota Safety Sense P System)

  • Left blind spot monitor sensor

    (with Blind Spot Monitor System)

  • CAN J/C Connector No. 1
  • CAN J/C Connector No. 6

    (with Blind Spot Monitor System)

WIRING DIAGRAM

without blind spot monitor system

with blind spot monitor system

PRECAUTION / NOTICE / HINT

NOTICE:

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.

    DTC confirmation procedure: Turn the blind spot monitor system ON using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch ON, turn the LDA main switch ON, then drive the vehicle at a speed of approximately 40 km/h for approximately 52 seconds.

  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

HINT:

  • Before disconnecting the related connectors for inspection, press on the body of each connector to make sure the connector is not loose or disconnected.
  • When a connector is disconnected, make sure the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK VEHICLE TYPE

(a) Check the vehicle type.

Result:

Result

Proceed to

without blind spot monitor system

A

with blind spot monitor system

B

B

GO TO STEP 4

A
  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (CAN J/C NO. 1)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect CAN junction connector No. 1.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F112-2 (CANH) - F112-13 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Forward recognition camera*1

F112-3 (CANH) - F112-14 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Millimeter Wave Radar Sensor Assembly*1

F112-4 (CANH) - F112-15 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

F112-5 (CANH) - F112-16 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

  • *1: with Toyota Safety Sense P system

*a

Front view of wire harness side connector

(to CAN junction connector No. 1)

*b

to forward recognition camera

(with Toyota Safety Sense P System)

*c

to millimeter wave radar sensor assembly

(with Toyota Safety Sense P System)

*d

to Central Gateway ECU (Network Gateway ECU)

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (Line to ECU or Sensor)

C

A

REPLACE CAN JUNCTION CONNECTOR NO. 1

C

GO TO STEP 8

B
  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (CAN J/C NO. 1 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F112-4 (CANH) - F112-15 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

F112-5 (CANH) - F112-16 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to CAN junction connector No. 1)

*b

to Central Gateway ECU (Network Gateway ECU)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE MAIN CAN BUS LINES OR CONNECTOR (CAN J/C NO. 1 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (CAN J/C NO. 6)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect CAN junction connector No. 6.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

M92-1 (CANH) - M92-12 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

M92-6 (CANH) - M92-17 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Left blind spot monitor sensor

M92-11 (CANH) - M92-22 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

CAN J/C Connector No. 1

*a

Front view of wire harness side connector

(to CAN junction connector No. 6)

*b

to Central Gateway ECU (Network Gateway ECU)

*c

to LH blind spot sensor

*d

to CAN junction connector No. 1

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (line to CAN junction connector No. 1)

C

NG (Line to ECU or Sensor)

D

A

REPLACE CAN JUNCTION CONNECTOR NO. 6

C

GO TO STEP 6

D

GO TO STEP 8

B
  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (CAN J/C NO. 6 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M92-1 (CANH) - M92-12 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to CAN junction connector No. 6)

*b

to Central Gateway ECU (Network Gateway ECU)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE MAIN CAN BUS LINES OR CONNECTOR (CAN J/C NO. 6 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (CAN J/C NO. 1)

(a) Reconnect connector M92 of CAN junction connector No. 6.

(b) Disconnect CAN junction connector No. 1.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F112-2 (CANH) - F112-13 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Forward recognition camera*1

F112-3 (CANH) - F112-14 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Millimeter Wave Radar Sensor Assembly*1

F112-4 (CANH) - F112-15 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

CAN J/C Connector No. 6

F112-5 (CANH) - F112-16 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

  • *1: with Toyota Safety Sense P system

*a

Front view of wire harness side connector

(to CAN junction connector No. 1)

*b

to forward recognition camera

(with Toyota Safety Sense P System)

*c

to millimeter wave radar sensor assembly

(with Toyota Safety Sense P System)

*d

to CAN junction connector No. 6

*e

to Central Gateway ECU (Network Gateway ECU)

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (line to CAN junction connector No. 6)

C

NG (Line to ECU or Sensor)

D

A

REPLACE CAN JUNCTION CONNECTOR NO. 1

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN JUNCTION CONNECTOR NO. 1 - CAN JUNCTION CONNECTOR NO. 6)

D

GO TO STEP 8

B
  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (CAN J/C NO. 1 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F112-5 (CANH) - F112-16 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to CAN junction connector No. 1)

*b

to Central Gateway ECU (Network Gateway ECU)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE MAIN CAN BUS LINES OR CONNECTOR (CAN J/C NO. 1 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector containing the CANH and CANL terminals of the ECU or sensor to which the shorted sub bus line is connected.

Click here

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F74-23 (CA1H) - F74-8 (CA1L)

Cable disconnected from negative (-) battery terminal

54 à 69 Ω

HINT:

  • If the resistance returns to normal (54 to 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short circuit in the ECU or sensor.
  • If the resistance does not return to normal when the connector is disconnected from the ECU or sensor, check the wire harness for a short circuit and repair or replace the wire harness or connector as necessary.

*a

Component with Wire Harness Connected

(central gateway ECU (network gateway ECU))

OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR