Network Operation

Check for Possible Short to GND in Bus Line 5

~8min read

DESCRIPTION

A short to GND may exist in one of the CAN bus lines when no resistance is detected between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or between terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom

Suspected Area

No resistance is detected between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or between terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

  • Short to GND in Main CAN Bus Line
  • Short to GND in Sub CAN Bus Line
  • Main body ECU (multiplex network body ECU)
  • Certification ECU (Smart Key ECU Assy)

    (with Smart Key System)

  • Central Gateway ECU (Network Gateway ECU)
  • Combination meter assembly
  • Air Conditioning Amplifier Assembly
  • Left Headlight ECU Subassembly

    (for LED Headlight)

  • CAN Junction Connector No. 3

WIRING DIAGRAM

with air conditioning pressure sensor installed on top

with air conditioning pressure sensor installed on side

PRECAUTION / NOTICE / HINT

NOTICE:

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.

    DTC Check Procedure: Turn the ignition switch to ON, turn the BSM system on using the BSM main switch (ON/OFF switch), turn the LDA main switch to ON, and wait at least 52 seconds.

  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Before replacing the Main Body ECU (Multiplex Network Body ECU) or the Certification ECU (Smart Key System ECU Assembly), refer to the registration section.*1

    Click here

  • When replacing the instrument cluster assembly, always use a new part. If an instrument cluster assembly that was installed in another vehicle is used, the stored information will not match the information transmitted by the vehicle, and a DTC may be stored.
  • *1: with Smart Key System

HINT:

  • Before disconnecting the related connectors for inspection, press on the body of each connector to make sure the connector is not loose or disconnected.
  • When a connector is disconnected, make sure the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINE (CAN JUNCTION CONNECTOR NO. 3)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the CAN junction connector No. 3.

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness side connector

(to CAN junction connector No. 3)

*b

to combination meter assembly

*c

to Main Body ECU (Multiplex Network Body ECU)

*d

to LH headlight ECU sub-assembly

(for LED Headlight)

*e

to air conditioning amplifier assembly

*f

to certification ECU (smart key system ECU assembly)

(with Smart Key System)

*g

to Central Gateway ECU (Network Gateway ECU)

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F114-1 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Combination meter assembly

F114-12 (CANL) - F41-4 (CG)

F114-2 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Main body ECU (multiplex network body ECU)

F114-13 (CANL) - F41-4 (CG)

F114-3 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

LH headlight ECU sub-assembly*1

F114-14 (CANL) - F41-4 (CG)

F114-4 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Air Conditioning Amplifier Assembly

F114-15 (CANL) - F41-4 (CG)

F114-5 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Certification ECU (smart key system ECU assembly)*2

F114-16 (CANL) - F41-4 (CG)

F114-6 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Central Gateway ECU (Network Gateway ECU)

F114-17 (CANL) - F41-4 (CG)

  • *1: for LED headlight
  • *2: with Smart Key System

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (Line to ECU or Sensor)

C

A

REPLACE CAN JUNCTION CONNECTOR NO. 3

C

GO TO STEP 3

B
  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINE (CAN JUNCTION CONNECTOR NO. 3 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness side connector

(to CAN junction connector No. 3)

*b

to Central Gateway ECU (Network Gateway ECU)

Standard resistance:

Tester Connection

Condition

Specified Condition

F114-6 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

F114-17 (CANL) - F41-4 (CG)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE MAIN CAN BUS LINE OR CONNECTOR (CAN J/C CONNECTOR NO. 3 - CENTRAL GATEWAY ECU)

  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector that includes the CANH and CANL terminals of the ECU or sensor to which the bus line shorted to GND is connected.

Click here

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Component with Wire Harness Connected

(central gateway ECU (network gateway ECU))

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

F74-15 (CA5H) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

F74-16 (CA5L) - F41-4 (CG)

HINT:

  • If the resistance changes to 200 Ω or more when the connector is disconnected from the ECU or sensor, there may be a short circuit in the ECU or sensor.
  • If the resistance does not return to normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness, and repair or replace the wire harness or connector as necessary.
OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR