Network Operation

Check for possible short circuit in bus lines 4

~8min read

DESCRIPTION

There may be a short circuit between the main CAN bus lines and/or between the sub CAN lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU is less than 54 Ω.

Symptom

Suspected Area

The resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU is 54 Ω or more.

  • Short circuit in main CAN bus lines
  • Short circuit in sub CAN bus lines
  • Central Gateway ECU (Network Gateway ECU)
  • Airbag sensor assembly
  • Steering angle sensor
  • Power steering ECU assembly
  • Brake Actuator Assembly
  • Occupant Detection ECU

    (with Occupant Detection ECU)

  • CAN Junction Connector No. 5
  • CAN Junction Connector No. 4

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.

    DTC check procedure: Turn the blind spot monitor system ON using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch ON, turn the LDA main switch ON, then drive the vehicle at a speed of approximately 60 km/h for approximately 5 minutes.

  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

HINT:

  • Before disconnecting the related connectors for inspection, press on the body of each connector to make sure the connector is not loose or disconnected.
  • When a connector is disconnected, make sure the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CAN J/C CONNECTOR NO. 5)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the CAN J/C connector No. 5.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness side connector

(to CAN junction connector No. 5)

*b

to CAN junction connector No. 4

*c

to Central Gateway ECU (Network Gateway ECU)

*d

to occupant detection ECU

(with Occupant Detection ECU)

*e

to brake actuator assembly

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F124-1 (CANH) - F124-12 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

CAN Junction Connector No. 4

F124-2 (CANH) - F124-13 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Central Gateway ECU (Network Gateway ECU)

F124-4 (CANH) - F124-15 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Occupant detection ECU*1

F124-5 (CANH) - F124-16 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Brake Actuator Assembly

  • *1: with occupant detection ECU

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (Line to CAN J/C connector No. 4)

C

NG (Line to ECU or Sensor)

D

A

REPLACE CAN J/C CONNECTOR NO. 5

C

GO TO STEP 3

D

GO TO STEP 5

B
  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CAN J/C CONNECTOR NO. 5 - CENTRAL GATEWAY ECU)

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F124-2 (CANH) - F124-13 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to CAN junction connector No. 5)

*b

to Central Gateway ECU (Network Gateway ECU)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE MAIN CAN BUS LINES OR CONNECTOR (CAN J/C CONNECTOR NO. 5 - CENTRAL GATEWAY ECU)

  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CAN J/C CONNECTOR NO. 4)

(a) Reconnect the F124 connector to the CAN J/C connector No. 5.

(b) Disconnect the CAN J/C connector No. 4.

(c) Measure the resistance according to the value(s) in the table below.

*a

Front view of wire harness side connector

(to CAN junction connector No. 4)

*b

to airbag sensor assembly

*c

to steering angle sensor

*d

to power steering ECU assembly

*e

to CAN junction connector No. 5

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F123-1 (CANH) - F123-12 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

Airbag sensor assembly

F123-5 (CANH) - F123-16 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Steering angle sensor

F123-6 (CANH) - F123-17 (CANL)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Power steering ECU assembly

F123-7 (CANH) - F123-18 (CANL)

Cable disconnected from negative (-) battery terminal

108 à 132 Ω

CAN Junction Connector No. 5

Result:

Result

Proceed to

OK

A

NG (Line to CAN J/C connector No. 5)

B

NG (Line to airbag sensor assembly)

C

NG (Line to ECU or Sensor)

D

A

REPLACE CAN JUNCTION CONNECTOR NO. 6

B

REPAIR OR REPLACE CONNECTOR OR MAIN CAN BUS LINES (CAN J/C CONNECTOR NO. 4 - CAN J/C CONNECTOR NO. 5)

D

GO TO STEP 5

C
  1. CHECK FOR POSSIBLE SHORT CIRCUIT IN CAN BUS LINES (CAN J/C CONNECTOR NO. 4 - AIRBAG SENSOR ASSEMBLY)

(a) Disconnect the F70 airbag sensor assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F123-1 (CANH) - F123-12 (CANL)

Cable disconnected from negative (-) battery terminal

1 MΩ or higher

*a

Front view of wire harness side connector

(to CAN junction connector No. 4)

*b

to airbag sensor assembly

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CONNECTOR OR MAIN CAN BUS LINES (CAN J/C CONNECTOR NO. 4 - AIRBAG SENSOR ASSEMBLY)

  1. CHECK FOR SHORT CIRCUIT IN CAN BUS LINES (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector containing the CANH and CANL terminals of the ECU or sensor to which the shorted sub bus line is connected.

Click here

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F74-22 (CA2H) - F74-7 (CA2L)

Cable disconnected from negative (-) battery terminal

54 à 69 Ω

HINT:

  • If the resistance returns to normal (54 to 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short circuit in the ECU or sensor.
  • If the resistance does not return to normal when the connector is disconnected from the ECU or sensor, check the wire harness for a short circuit and repair or replace the wire harness or connector as necessary.

*a

Component with Wire Harness Connected

(central gateway ECU (network gateway ECU))

OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR