Network Operation

Check for possible short to GND in bus line 4

~8min read

DESCRIPTION

A short between one of the CAN bus lines and GND may exist when no resistance is detected between terminal 22 (CA2H) of the Central Gateway ECU and terminal 4 (CG) of the DLC3, or between terminal 7 (CA2L) of the Central Gateway ECU and terminal 4 (CG) of the DLC3.

Symptom

Suspected Area

No resistance is detected between terminal 22 (CA2H) of the Central Gateway ECU and terminal 4 (CG) of the DLC3, or between terminal 7 (CA2L) of the Central Gateway ECU and terminal 4 (CG) of the DLC3.

  • Short to GND in Main CAN Bus Line
  • Short to GND in Sub CAN Bus Line
  • Central Gateway ECU (Network Gateway ECU)
  • Airbag sensor assembly
  • Steering angle sensor
  • Power steering ECU assembly
  • Brake Actuator Assembly
  • Occupant Detection ECU

    (with Occupant Detection ECU)

  • CAN Junction Connector No. 5
  • CAN Junction Connector No. 4

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Because the diagnostic sequence is important for accurate diagnosis, be sure to perform troubleshooting using the section "How to Use Troubleshooting" when CAN communication system DTCs are output.

    Click here

  • Before measuring the CAN bus resistance, turn the ignition switch OFF and leave the vehicle for at least 1 minute without using the key or switches, and without opening or closing any doors. Then disconnect the cable from the negative (-) battery terminal and leave the vehicle for at least 1 minute before measuring the resistance.
  • After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

    Click here

  • After completing repairs, perform the DTC check procedure and make sure the DTCs are not output again.

    DTC check procedure: Turn the blind spot monitor system ON using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch ON, turn the LDA main switch ON, then drive the vehicle at a speed of approximately 60 km/h for approximately 5 minutes.

  • After repair, perform the CAN bus check and make sure all ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

HINT:

  • Before disconnecting the related connectors for inspection, press on the body of each connector to make sure the connector is not loose or disconnected.
  • When a connector is disconnected, make sure the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINE (CAN J/C CONNECTOR No. 5)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the CAN J/C connector No. 5.

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness side connector

(to CAN junction connector No. 5)

*b

to CAN junction connector No. 4

*c

to Central Gateway ECU (Network Gateway ECU)

*d

to occupant detection ECU

(with Occupant Detection ECU)

*e

to brake actuator assembly

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F124-1 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

CAN Junction Connector No. 4

F124-12 (CANL) - F41-4 (CG)

F124-2 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Central Gateway ECU (Network Gateway ECU)

F124-13 (CANL) - F41-4 (CG)

F124-4 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Occupant detection ECU*1

F124-15 (CANL) - F41-4 (CG)

F124-5 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Brake Actuator Assembly

F124-16 (CANL) - F41-4 (CG)

  • *1: with occupant detection ECU

Result:

Result

Proceed to

OK

A

NG (line to the central gateway ECU (network gateway ECU))

B

NG (Line to CAN J/C connector No. 4)

C

NG (Line to ECU or Sensor)

D

A

REPLACE CAN J/C CONNECTOR NO. 5

C

GO TO STEP 3

D

GO TO STEP 4

B
  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINES (CAN J/C CONNECTOR No. 5 - CENTRAL GATEWAY ECU)

(a) Disconnect connector F74 of the central gateway ECU (network gateway ECU).

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness side connector

(to CAN junction connector No. 5)

*b

to Central Gateway ECU (Network Gateway ECU)

Standard resistance:

Tester Connection

Condition

Specified Condition

F124-2 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

F124-13 (CANL) - F41-4 (CG)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (CAN J/C CONNECTOR No. 5 - CENTRAL GATEWAY ECU)

  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINE (CAN J/C CONNECTOR No. 4)

(a) Disconnect CAN J/C connector No. 4.

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness side connector

(to CAN junction connector No. 4)

*b

to airbag sensor assembly

*c

to steering angle sensor

*d

to power steering ECU assembly

*e

to CAN junction connector No. 5

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

Connects to

F123-1 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Airbag sensor assembly

F123-12 (CANL) - F41-4 (CG)

F123-5 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Steering angle sensor

F123-16 (CANL) - F41-4 (CG)

F123-6 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

Power steering ECU assembly

F123-17 (CANL) - F41-4 (CG)

F123-7 (CANH) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

CAN Junction Connector No. 5

F123-18 (CANL) - F41-4 (CG)

Result:

Result

Proceed to

OK

A

NG (Line to CAN J/C connector No. 5)

B

NG (Line to ECU or Sensor)

C

A

REPLACE CAN J/C CONNECTOR NO. 4

B

REPAIR OR REPLACE CONNECTOR OR CAN BUS MAIN LINE (CAN J/C CONNECTOR No. 4 - CAN J/C CONNECTOR No. 5)

C

GO TO STEP 4

  1. CHECK FOR POSSIBLE SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector that includes the CANH and CANL terminals of the ECU or sensor to which the bus line shorted to GND is connected.

Click here

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Component with Wire Harness Connected

(central gateway ECU (network gateway ECU))

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

F74-22 (CA2H) - F41-4 (CG)

Cable disconnected from negative (-) battery terminal

200 Ω or higher

F74-7 (CA2L) - F41-4 (CG)

HINT:

  • If the resistance changes to 200 Ω or more when the connector is disconnected from the ECU or sensor, there may be a short circuit in the ECU or sensor.
  • If the resistance does not return to normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness, and repair or replace the wire harness or connector as necessary.
OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR