Precautions
PRECAUTION
IGNITION SWITCH TERMS
(a) The type of ignition switch used varies depending on vehicle specifications. The terms listed in the table below are used in this section.
Term | Ignition Switch (Position) | Engine Switch (Condition) |
|---|---|---|
Ignition Switch in OFF position |
LOCK |
OFF (Locked) |
Ignition Switch in ACC position |
ACC |
ON (ACC) |
Ignition Switch in ON position |
ON |
ON (IG) |
Starting the engine |
START |
ON (Starting) |
CAUTION / NOTICE FOR REPLACING INSTRUMENT CLUSTER ASSEMBLY
(a) When replacing the instrument cluster assembly, replace it with a new part. If an instrument cluster assembly installed in another vehicle is used, the recorded information will not match the information transmitted by the vehicle, and a DTC may be stored.
CAN COMMUNICATION SYSTEM TROUBLESHOOTING
(a) Because the diagnostic sequence is important for accurate diagnosis, make sure to perform troubleshooting using the "How to Use Troubleshooting" section when DTCs related to the CAN communication system are output.
Click here
![]()
(b) Precautions when handling the steering system
(1) Be careful when replacing parts. Incorrect replacement may affect the steering system performance and cause unsafe driving.
Click here![]()
(c) Precautions when handling the SRS airbag system
NOTICE:
This vehicle is equipped with a Supplemental Restraint System (SRS) including components such as the driver and front passenger airbags. Failure to follow the correct order of maintenance tasks may cause the SRS to deploy accidentally during servicing and result in a serious accident. Before performing any maintenance operation (removal or installation of parts, inspection or replacement), carefully read the SRS precautions.
Click here
![]()
(d) Precautions when disconnecting a wire harness from a CAN J/C connector
(1) When disconnecting a wire harness from a CAN J/C connector, use tape or labels to identify each connector and make sure to reconnect each connector to its original position on the CAN J/C connector.
HINT:
- Reconnecting a connector to a position other than its original location on the CAN J/C connector does not affect system performance. However, reconnecting the connectors to their original locations facilitates future servicing and prevents adverse effects on the wire harnesses, such as excessive tension.
- For more information on how to identify the ECUs or sensors connected to the CAN J/C connector, refer to the ECU terminals.
Click here
.gif)
(e) Bus Line Repair
(1) After repairing a bus cable by soldering, wrap the repaired area with insulating tape.
*a |
Soldered area to be wrapped with insulating tape |
NOTICE:
- When installing, make sure these lines are twisted together, as CAN bus lines may be affected by electrical noise if they are not twisted.
- Make sure there is no gap between the CANH wire and the CANL wire.
- Make sure the distance between the first winding of the wires and the connector is less than 80 mm (3.15 in.).
- When repairing CAN bus lines, do not change the length of the lines. (Make sure the length of the CANH bus line and the length of the CANL bus line are the same.)
(2) Do not make branch wiring between connectors.
*a |
Branch Wire |
NOTICE:
- Using branch wiring cancels the ability of twisted-pair bus lines to resist interference.
- Do not use a twisted wire pair for branch wiring.
(f) Handling of Connectors
(1) When checking resistance with a tester, insert the tester probes from the rear (wire harness side) of the connector.
*a |
Tester probe |
(2) If the tester cannot be inserted from the rear of the connector, use diagnostic cables and measure from the front side of the connector.
*a |
Diagnosis cable |
(g) Precautions When Replacing an ECU with Gateway Function (Sub-bus Control ECU)
(1) When replacing an ECU with gateway function (sub-bus control ECU) with an ECU that was installed on another vehicle, initialize the sub-bus control ECU to erase the bus information that was stored.
Click here![]()
NOTICE:
If the stored bus information does not match the current sub-bus configuration, DTCs may be stored and security functions may activate.
HINT:
It is not necessary to initialize the gateway control ECU (sub-bus control ECU) when using a sub-bus control ECU that was installed on another vehicle with the same sub-bus configuration.
(h) Precautions When an ECU with Gateway Function (Sub-bus Control ECU) Detects Communication DTCs for ECUs Not Connected to the ECU
(1) Refer to the precautions for replacing an ECU with gateway function (sub-bus control ECU) and initialize the ECU connection information.
(2) Clear the DTCs and make sure no DTCs are output.
(i) Difference Between a Factory-installed TOYOTA Navigation Receiver and an Optional CAN-compatible Navigation Receiver
(1) Some navigation receivers are available as optional CAN-compatible devices. Make sure optional CAN-compatible devices do not have the same diagnostic functions or characteristics as the TOYOTA factory-installed navigation receivers.
NOTICE:
- Optional CAN-compatible navigation receivers receive data from the CAN communication system. However, most optional CAN-compatible navigation receivers do not send signals to the main CAN bus line.
- Most optional CAN-compatible navigation receivers do not appear on the "Communication Bus Check" screen of the Techstream.
- When checking DTCs using the Techstream, DTCs for optional CAN-compatible navigation receivers do not appear on the Techstream.