Fail-Safe Table
FAIL-SAFE TABLE
FAIL-SAFE FUNCTION
(a) When communication fails on one of the CAN bus lines (communication lines), the fail-safe function(s) is (are) activated. The fail-safe function specified for each system operates to prevent possible system malfunctions.
(b) The following table shows the effects on each system when communication is not possible. (For more information, refer to the pages for each system.)
Function | Main Control (Main ECU that determines the controls) | Related System | Fail-safe operation | Can Be Detected by Driver | DTC Detection (ECU that stored the DTCs) |
|---|---|---|---|---|---|
ABS Control |
Brake Actuator Assembly |
- |
Only EBD control is available. |
|
U0073 (Brake Actuator Assembly) |
VSC Control |
Brake Actuator Assembly |
|
|
|
U0073 U0100 U0123 U0126 (Brake Actuator Assembly) |
TRAC Control |
Brake Actuator Assembly |
|
|
|
U0073 U0100 U0123 U0126 (Brake Actuator Assembly) |
Hill-Start Assist Control
|
Brake Actuator Assembly |
|
|
|
U0073 U0100 U0123 U0126 (Brake Actuator Assembly) |
PCS Control
|
Brake Actuator Assembly |
Millimeter wave radar sensor assembly |
PCS braking control is disabled. |
|
U0073 (Brake Actuator Assembly) |
ACC Control
|
Brake Actuator Assembly |
ECM |
ACC braking control is disabled. |
|
U0073 (Brake Actuator Assembly) |
Brake Hold Control
|
Brake Actuator Assembly |
|
Brake hold control is disabled. |
|
U0073 U0100 U0123 U0126 U0142 (Brake Actuator Assembly) |
DAR Control
|
Brake Actuator Assembly |
|
DAR control is disabled. |
|
U0073 U0100 U0123 U0126 U0142 (Brake Actuator Assembly) |
Vehicle Speed Display |
Combination meter assembly |
Brake Actuator Assembly |
The speedometer is controlled based on a default vehicle speed of approximately 0 km/h. |
- |
U0129 (Combination Meter Assembly) |
Tachometer Display |
Combination meter assembly |
ECM |
The tachometer needle stays at 0 rpm. |
- |
U0100 (Combination Meter Assembly) |
Combination Meter Display
|
Combination meter assembly |
|
|
- |
U0100 U0129 U0131 U0151 U0182 (Combination Meter Assembly) |
Air Conditioning Control
|
Air Conditioning Amplifier Assembly |
ECM |
|
- |
U0100 (Air conditioning amplifier assembly) |
Compressor control
|
Air Conditioning Amplifier Assembly |
ECM |
If the target frame cannot be received, the previous values are retained. |
- |
U0100 (Air conditioning amplifier assembly) |
Simple charge
|
Air Conditioning Amplifier Assembly |
Power steering ECU assembly |
If the target frame cannot be received, the previous values are retained. |
- |
U0131 (Air conditioning amplifier assembly) |
Instrument panel dimmer control
|
Air Conditioning Amplifier Assembly |
Main body ECU (multiplex network body ECU) |
If the target frame cannot be received, the previous values are retained. |
- |
U0142 (Air conditioning amplifier assembly) |
Destination determination
|
Air Conditioning Amplifier Assembly |
Main body ECU (multiplex network body ECU) |
If the target frame cannot be received, the previous values are retained. |
- |
U0142 (Air conditioning amplifier assembly) |
Ambient temperature correction control
|
Air Conditioning Amplifier Assembly |
Combination meter assembly |
|
- |
U0155 (Air conditioning amplifier assembly) |
Solar calibration control
|
Air Conditioning Amplifier Assembly |
Main body ECU (multiplex network body ECU) |
|
- |
U0142 (Air conditioning amplifier assembly) |
Outside temperature compensation control
|
Air Conditioning Amplifier Assembly |
Main body ECU (multiplex network body ECU) |
If the target frame cannot be received, the previous values are retained. |
- |
U0142 (Air conditioning amplifier assembly) |
Freeze frame data transmission function
|
Air Conditioning Amplifier Assembly |
Central Gateway ECU (Network Gateway ECU) |
If the target frame cannot be received, the previous values are retained. |
- |
- |
Blind spot monitor control
|
Left blind spot monitor sensor |
|
- |
Displays messages on the multi-information display. |
U0100 U0126 U0129 U0142 (Left blind spot sensor) |
LDA system
|
Front Area Recognition Camera |
|
Control stopped. |
|
U0100 U0123 U0126 U0129 U0131 U0142 U0155 U0235 U023A (Front recognition camera) |
Automatic high beam function
|
Front Area Recognition Camera |
|
The current state is maintained. |
|
B124B (main body ECU (multiplex network body ECU)) |
Road sign recognition function
|
Front Area Recognition Camera |
|
The road sign assist function is disabled. |
|
U0123 U0129 (Front recognition camera) |
Dynamic Radar Cruise Control System
|
Millimeter wave radar sensor assembly |
|
Control stopped. |
Displays messages on the multi-information display. |
U0100 U0125 U0126 U0129 (Millimeter wave radar sensor assembly) |
Pre-Collision System
|
Millimeter wave radar sensor assembly |
|
Control stopped. |
|
U0100 U0125 U0126 U0129 U0235 U023A U1002 (Millimeter wave radar sensor assembly) |
Opening function
|
|
|
|
- |
U0100 U0142 U0155 (Certification ECU (smart key ECU assembly)) |
Remote Control Function
|
Certification ECU (Smart Key ECU Assy) |
Main body ECU (multiplex network body ECU) |
Remote lock/unlock does not operate. |
- |
U0142 (Certification ECU (smart key ECU assembly)) |
Engine switch backlight control
|
Certification ECU (Smart Key ECU Assy) |
Main body ECU (multiplex network body ECU) |
|
- |
U0142 (Certification ECU (smart key ECU assembly)) |
Security indicator display function
|
Certification ECU (Smart Key ECU Assy) |
Main body ECU (multiplex network body ECU) |
The security status cannot be displayed normally (it illuminates during preparation of the security warning message / the security warning message). |
- |
U0142 (Certification ECU (smart key ECU assembly)) |
Start hold control
|
Certification ECU (Smart Key ECU Assy) |
ECM |
If CAN communication fails, engine start stop is estimated from the direct NE. |
- |
- |
Power steering control
|
Power steering ECU assembly |
|
|
The EPS warning light comes on. |
U0100 U0129 (Power Steering ECU Assembly) |
Assist map selection
|
Power steering ECU assembly |
ECM |
The default map is used for assist because the assist map quality cannot be selected. (Steering may feel different) |
The EPS warning light comes on. |
C1581 (Power Steering ECU Assembly) |
VDIMα system
|
Power steering ECU assembly |
Brake Actuator Assembly |
VDIMα control is stopped. |
- |
U0129 (Power Steering ECU Assembly) |
Engine/hybrid switching
|
Power steering ECU assembly |
ECM |
Control is temporarily performed with the power steering assist amount set for this use when the vehicle speed is 100 km/h. |
The EPS warning light comes on. |
U0100 (Power Steering ECU Assembly) |
Engine system indicator display
|
ECM |
Combination meter assembly |
|
- |
- |
Electrical load control
|
ECM |
|
Fast idle based on electrical load is not performed. |
Not possible. (Idle speed varies). |
- |
Cooperative air conditioning control
|
ECM |
Air Conditioning Amplifier Assembly |
The air conditioning system does not use cooperative control. (Fast idle is not performed.) |
The air conditioning system does not operate. |
- |
Load control
|
ECM |
|
Fast idle control is not performed according to the load request. |
The rear lights flicker and the blower airflow changes. |
- |
Sprung mass damping control
|
ECM |
Brake Actuator Assembly |
The vehicle sprung mass damping control does not operate. Transitional drive force control is not used to improve the behavior (pitch and bounce) of the vehicle's sprung mass when disturbed. |
- |
- |
Eco driving indicator
|
ECM |
- |
- |
No information is displayed. |
- |
Integrated control (VDM)
|
ECM |
|
Does not evaluate the requested torque based on accelerator pedal operation and does not perform characteristic torque control according to driving conditions; as a result, drivability, performance and acceleration feel are not improved. |
- |
- |
Eco control
|
ECM |
|
Eco mode does not operate. |
- |
- |
ECT system indicator display
|
ECM |
Combination meter assembly |
The indicator does not illuminate. |
- |
- |
Neutral control
|
ECM |
|
Neutral control is not performed. |
- |
U0129 (ECM) |
Clutch-off downshift shift point change according to air conditioning load
|
ECM |
Air Conditioning Amplifier Assembly |
Clutch-off downshift does not operate. |
The performance of clutch-off downshift shock reduction deteriorates. |
- |
Cruise control
|
ECM |
|
The cruise control does not operate. |
Displays messages on the multi-information display. |
- |
Headlight levelling control (headlight control)
|
Left Headlight ECU Subassembly |
|
Control stopped. |
- |
U0129 U0142 (LH headlight ECU sub-assembly) |
Headlight levelling indicator
|
Left Headlight ECU Subassembly |
Combination meter assembly |
Maintains the state of the headlight levelling indicator. |
- |
U0155 (LH headlight ECU sub-assembly) |
Destination identification
|
Left Headlight ECU Subassembly |
|
- |
- |
U0100 U0142 (LH headlight ECU sub-assembly) |
Low beam, high beam, position lights and side marker lights
|
Main body ECU (multiplex network body ECU) |
Left Headlight ECU Subassembly |
The low beam, position lights and side marker lights are forced on. |
- |
U0142 (LH headlight ECU sub-assembly) |
LED headlight indicator
|
Left Headlight ECU Subassembly |
Combination meter assembly |
Maintains the state of the LED headlight indicator. |
|
U0073 U1000 (LH headlight ECU sub-assembly) |
Door Lock
|
Main body ECU (multiplex network body ECU) |
Airbag sensor assembly |
Key-linked door locking/unlocking is performed even when the ignition switch is in the ON position and the driver's seat belt is fastened. |
- |
U0151 (main body ECU (multiplex network body ECU)) |
Alarm
|
Main body ECU (multiplex network body ECU) |
|
- |
- |
U0100 U0120 (main body ECU (multiplex network body ECU)) |
Automatic display brightness dimming
|
Main body ECU (multiplex network body ECU) |
Combination meter assembly |
Automatically performs display dimming control when Tail mode is not cancelled (when the illumination signal value of the light sensor is lower than the display dimming value, the brightness of the cabin and indicators is reduced). |
- |
U0155 (main body ECU (multiplex network body ECU)) |
Lighting
|
Main body ECU (multiplex network body ECU) |
|
|
The map light does not turn off immediately after the vehicle is exited. |
U0101 U0327 (main body ECU (multiplex network body ECU)) |
Diagnosis/C-BEST
|
- |
All ECUs connected to the CAN |
Exits diagnostic mode |
- |
- |
Occupant Classification System
|
Airbag sensor assembly |
Occupant Detection ECU |
The SRS components do not deploy. |
The SRS warning light comes on. |
U0154 (airbag sensor assembly) |
Smart key / remote control function
|
Certification ECU (Smart Key ECU Assy) |
Certification ECU (Smart Key ECU Assy) |
Lock/unlock by opening is not possible. |
- |
U0327 (main body ECU (multiplex network body ECU)) |
Light control
|
Main body ECU (multiplex network body ECU) |
ECM |
The daytime running light control is not performed. |
- |
U0100 (main body ECU (multiplex network body ECU)) |
TPMS
|
Main body ECU (multiplex network body ECU) |
Combination meter assembly |
Sends the initial communication value to BERKES. |
The tire pressure monitoring sensor indicator in the instrument cluster assembly flashes for 1 minute and then stays on. |
U0155 (main body ECU (multiplex network body ECU)) |
Automatic high beam
|
Main body ECU (multiplex network body ECU) |
|
The system does not operate. |
|
U023A (main body ECU (multiplex network body ECU)) |
Light control
|
Left Headlight ECU Subassembly |
Main body ECU (multiplex network body ECU) |
- |
|
U0182 (main body ECU (multiplex network body ECU)) |
Occupant Detection |
Occupant Detection ECU |
|
Outputs signals indicating a malfunction of the airbag sensor assembly. |
The SRS warning light comes on. |
U0125 U0129 (Occupant detection ECU) |
Destination identification
|
Radio and Display Receiver Assembly |
Main body ECU (multiplex network body ECU) |
Determines the destination based on the last value received and operates each respectively (when there is no last value, the system operates using the default value). |
The time zone and language selection screens differ from the actual destination. |
U0073 U0140 (Radio and display receiver assembly) |
Vehicle customization function
|
Radio and Display Receiver Assembly |
|
|
- |
U0073 (Radio and display receiver assembly) |
Meter-linked function
|
Radio and Display Receiver Assembly |
Combination meter assembly |
|
- |
U0073 U0155 (Radio and display receiver assembly) |
Sound adjustment function information
|
Radio and Display Receiver Assembly |
Front Area Recognition Camera |
Audio mute is canceled. |
- |
U0073 (Radio and display receiver assembly) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
Combination meter assembly |
The function is disabled. |
Notification displayed on smartphone via the app. |
U0155 (DCM (Data Communication Module)) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
Main body ECU (multiplex network body ECU) |
The function is disabled. |
Notification displayed on smartphone via the app. |
U0142 (DCM (Data Communication Module)) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
Main body ECU (multiplex network body ECU) |
The function is disabled. |
Notification displayed on smartphone via the app. |
U0142 U0198 (DCM (Data Communication Module)) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
Radio and Display Receiver Assembly |
The function is disabled. |
- |
U0163 (DCM (Data Communication Module)) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
Radio and Display Receiver Assembly |
The function is disabled. |
- |
U0163 (DCM (Data Communication Module)) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
|
The function is disabled. |
Notification displayed on smartphone via the app. |
U0142 U0155 (DCM (Data Communication Module)) |
TOYOTA Entune system
|
DCM (Telematics Transceiver) |
Main body ECU (multiplex network body ECU) |
The function is disabled. |
Notification displayed on smartphone via the app. |
U0142 (DCM (Data Communication Module)) |