Body Exterior, Doors, Roof & Vehicle Security

B2401 Ign Open

15steps
~90min
4/5difficulty
Done 0 of 15
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B2401–86

IGN OPEN

(Ignition open)
Diagnosis condition All times
Signal (terminal) Ignition switch ON signal (CAN communication)
Threshold

When all of the following conditions are satisfied

  • CAN communication is normal

  • Automatic back door control module receives wake up signal via CAN communication with BCM

  • Automatic back door control module cannot detect ignition switch ON signal via CAN communication with IPDM E/R

Diagnosis delay time –
B2401–87

IGN OPEN

(Ignition open)
Diagnosis condition All times
Signal (terminal) CAN communication
Threshold When automatic back door control module can not communicate CAN communication signal
Diagnosis delay time 2 seconds

POSSIBLE CAUSE

  • CAN communication system

  • BCM

  • IPDM E/R

  • Automatic back door control module

FAIL-SAFE

Inhibit automatic back door system auto open/close function

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AUTO BACK DOOR”.

Is DTC detected?

YES>>

DTC “B2401-86”: Refer to DTC Diagnosis Procedure (B2401-86).

YES>>

DTC “B2401-87”: Refer to DTC Diagnosis Procedure (B2401-87).

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure (B2401-86)

CHECK DTC OF BCM AND IPDM E/R

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “BCM” and “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Index (BCM) or DTC Index (IPDM E/R).

NO>>

GO TO 2.

CHECK IGN SW DATA MONITOR ITEM

CONSULT

  1. Select “IGN SW” in “Data Monitor” mode of “AUTO BACK DOOR”.

  2. Check that the function operates normally according to the following conditions.

Monitor itemConditionStatus
IGN SW Ignition switch ON position ON
Other than ON position OFF

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 4.

ERASE DTC

CONSULT

  1. Select “Self Diagnostic Result” mode of “AUTO BACK DOOR”

  2. Erase DTC, and then repeat “DTC CONFIRMATION PROCEDURE”. Refer to DTC Confirmation Procedure.

Is DTC “B2401-86” detected?

YES>>

GO TO 4.

NO>>

Check intermittent incident. Refer to Intermittent Incident.

REPLACE AUTOMATIC BACK DOOR CONTROL MODULE

CONSULT

  1. Ignition switch OFF.

  2. Replace automatic back door control module. Refer to Removal and Installation.

  3. Ignition switch ON.

  4. Select “Self Diagnostic Result” mode of “AUTO BACK DOOR”.

Is DTC “B2401-86” detected?

YES>>

Check CAN communication trouble. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

Diagnosis Procedure (B2401-87)

CHECK CAN COMMUNICATION TROUBLE DIAGNOSIS

Check CAN communication trouble diagnosis. Refer to Trouble Diagnosis Flow Chart.

>>

GO TO 2.

ERASE DTC

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AUTO BACK DOOR”.

  3. Erase DTC, and then repeat “DTC CONFIRMATION PROCEDURE”. Refer to DTC Confirmation Procedure.

Is DTC “B2401–87” detected?

YES>>

Replace automatic back door control module. Refer to Removal and Installation.

NO>>

Inspection End.