Theft Deterrent / Keyless Entry

ECU Terminals

126steps
~756min
4/5difficulty
Done 0 of 126

ECU TERMINALS

INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Related Data List Item

F1-18 (E) - Body ground

-

W-B - Body ground

Ground

Always

Below 1 Ω

-

F1-4 (+B) - F1-18 (E)

Input

L - W-B

Power supply

Always

11 à 14 V

-

F1-15 (CUTB) - F1-18 (E)

Input

SB - W-B

Dark current cut-off pin*

Always

11 à 14 V

-

  • *: To prevent the vehicle battery from being drained during long-distance shipping, a fuse that cuts off unnecessary electrical loads is installed in the circuit for shipping. If this fuse is removed, a circuit interruption occurs. If the fuse between the CUTB terminal and the battery is removed and the circuit is interrupted, the smart key system ECU (smart key ECU assembly) switches to a certain control mode (e.g., the transmission of radio waves every 0.25 seconds that form the detection area stops).

(c) Reconnect the F1 connector to the certification ECU (smart key ECU assembly).

(d) Measure the voltage and check the pulses according to the value(s) in the table below.

Tester Connection

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Related Data List Item

F1-17 (IG1D) - F1-18 (E)

Output

GR - W-B

IG power supply

Engine switch OFF → ON (IG)

Below 1 V → 10 V minimum

-

M67-17 (CLG1) - F1-18 (E)

Output

G - W-B

Output to driver side door electronic key antenna

[the request signal is sent to the door electronic key antenna from the smart key system ECU (smart key ECU assembly) to form a detection area]

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly in detection area*1)

Pulse generation

(See waveform 1)

Overhead + Driver Side (key diagnostic mode)

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly outside detection area*1)

Pulse generation

(see waveform 2)

M67-17 (CLG1) - F1-18 (E)

Input

G - W-B

Driver side door lock sensor input

(the front left door outside handle assembly lock sensor activation signal is sent to the smart key system ECU (smart key ECU assembly))

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors closed
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly outside detection area*1)

  5. Driver side door lock sensor touched

Pulse generation

(See waveform 3)

D-Door Trigger Switch

M67-17 (CLG1) - F1-18 (E)

Input

G - W-B

Driver side door unlock sensor input

(when the system is in unlock standby mode and the unlock sensor is touched, the door electronic key antenna sends the unlock sensor input signal (detection) to the smart key system ECU (smart key ECU assembly))

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors locked
  4. Electronic key transmitter sub-assembly not near vehicle
  5. Driver side door unlock sensor touched

Pulse generation

(see waveform 4)

D-Door Touch Sensor

M67-16 (CG1B) - F1-18 (E)

Output

R - W-B

Output to driver side electronic key antenna (terminal on opposite side of CLG1 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly in detection area*1)

Pulse generation

(see waveform 5)

Overhead + Driver Side (key diagnostic mode)

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly outside detection area*1)

Pulse generation

(see waveform 6)

M67-15 (CLG2) - F1-18 (E)

Output

G - W-B*2

P - W-B*3

Output to front passenger electronic key antenna

[the request signal is sent to the door electronic key antenna from the smart key system ECU (smart key ECU assembly) to form a detection area]

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly in detection area*1)

Pulse generation

(See waveform 1)

Overhead + Passenger Side (key diagnostic mode)

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly outside detection area*1)

Pulse generation

(see waveform 2)

M67-15 (CLG2) - F1-18 (E)

Input

G - W-B*2

P - W-B*3

Front passenger side door lock sensor input

(the front right door outside handle assembly lock sensor activation signal is sent to the smart key system ECU (smart key ECU assembly))

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors closed
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly outside detection area*1)

  5. Front passenger side door lock sensor touched

Pulse generation

(See waveform 3)

P-Door Trigger Switch

M67-15 (CLG2) - F1-18 (E)

Input

G - W-B*2

P - W-B*3

Front passenger side door unlock sensor input

(when the system is in unlock standby mode and the unlock sensor is touched, the door electronic key antenna sends the unlock sensor input signal (detection) to the smart key system ECU (smart key ECU assembly))

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors locked
  4. Electronic key transmitter sub-assembly not near vehicle
  5. Front passenger side door unlock sensor touched

Pulse generation

(see waveform 4)

P-Door Touch Sensor

M67-14 (CG2B) - F1-18 (E)

Output

R - W-B

Output to front passenger electronic key antenna (terminal on opposite side of CLG2 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly in detection area*1)

Pulse generation

(see waveform 5)

Overhead + Passenger Side (key diagnostic mode)

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (electronic key transmitter sub-assembly outside detection area*1)

Pulse generation

(see waveform 6)

F1-8 (CLG5) - F1-18 (E)

Output

SB - W-B

Output to interior electronic key antenna assembly No. 1 (front floor)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 7)

Overhead + Front Room (key diagnostic mode)

F1-9 (CG5B) - F1-18 (E)

Output

R - W-B

Output to interior electronic key antenna assembly No. 1 (front floor) (terminal on opposite side of CLG5 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 7)

Overhead + Front Room (key diagnostic mode)

M67-11 (CLG7) - F1-18 (E)

Output

B - W-B

Output to interior electronic key antenna assembly No. 3 (inside luggage compartment)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 7)

Overhead + Back Door (inside) (key diagnostic mode)

M67-10 (CG7B) - F1-18 (E)

Output

W - W-B

Output to interior electronic key antenna assembly No. 3 (front floor) (terminal on opposite side of CLG7 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 7)

Overhead + Back Door (inside) (key diagnostic mode)

M67-13 (CLG8) - F1-18 (E)

Output

Y - W-B

Output to electronic key antenna (outside luggage compartment)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors closed
  4. Trunk door opener switch assembly OFF → ON

Pulse generation

(see waveform 8)

Overhead + Back Door (key diagnostic mode)

M67-12 (CG8B) - F1-18 (E)

Output

W - W-B

Output to electronic key antenna (outside luggage compartment) (terminal on opposite side of CLG8 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors closed
  4. Trunk door opener switch assembly OFF → ON

Pulse generation

(see waveform 8)

Overhead + Back Door (key diagnostic mode)

M67-26 (TSW5) - F1-18 (E)

Input

LG - W-B

Trunk door opener switch assembly signal input (opener switch)

Trunk door opener switch assembly (opener switch) OFF → ON

Pulse generation

(see waveform 9)

Tr/B-Door Unlock SW

M67-27 (TSW6) - F1-18 (E)

Input

GR - W-B

Trunk door opener switch assembly signal input (lock switch)

Trunk door opener switch assembly (lock switch) OFF → ON

Pulse generation

(see waveform 9)

Tr/B-Door Lock SW

M67-18 (RCO) - F1-18 (E)

Output

LG - W-B

Output to electronic key and TPMS receiver assembly

(power supply for the electronic key and TPMS receiver assembly. The smart key system ECU (smart key ECU assembly) sends 5 V when the receiver turns on.)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside detection area but kept within range of remote control function
  3. Electronic key transmitter sub-assembly lock or unlock switch not pressed → pressed

Pulse generation

(see waveform 10)

-

M67-19 (RDAM) - F1-18 (E)

Input

GR - W-B

The electronic key and TPMS receiver assembly checks the data from the electronic key transmitter sub-assembly.

The electronic key and TPMS receiver assembly sends the data from the electronic key transmitter sub-assembly to the smart key system ECU (smart key ECU assembly) (the electronic key and TPMS receiver assembly intermittently grounds the 12 V signal from the smart key system ECU (smart key ECU assembly)).

Go to step:

  1. Engine switch in OFF position
  2. All doors locked
  3. Electronic key transmitter sub-assembly outside vehicle
  4. Electronic key transmitter sub-assembly outside detection area but kept within range of remote control function
  5. Electronic key transmitter sub-assembly lock or unlock switch not pressed → pressed

Pulse generation

(see waveform 11)

-

M67-20 (CSEL) - F1-18 (E)

Output

V - W-B

Communication channel control circuit

Procedure:

  1. Engine switch in OFF position
  2. All doors closed

Below 1 V → pulse generation

-

  • *1: For details on the detection area of the walk-away/intelligent unlock function, refer to the operation check.

    Click here

  • *2: TMMT made
  • *3: Manufactured by TMC

(e) Check waveform 1 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 1 (reference)

Item

Content

Tester Connection

M67-17 (CLG1) - F1-18 (E)

M67-15 (CLG2) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (Electronic key transmitter subassembly located inside the detection area*)

  • *: For details on the detection area of the walk-away/intelligent unlock function, refer to the operation check.

    Click here

(f) Check waveform 2 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 2 (reference)

Item

Content

Tester Connection

M67-17 (CLG1) - F1-18 (E)

M67-15 (CLG2) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 100 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (Electronic key transmitter subassembly located outside the detection area*)

  • *: For details on the detection area of the walk-away/intelligent unlock function, refer to the operation check.

    Click here

(g) Check waveform 3 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

*a

Lock sensor not touched

*b

Lock sensor touched

Waveform 3 (reference)

Item

Content

Tester Connection

M67-17 (CLG1) - F1-18 (E)

M67-15 (CLG2) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 40 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors closed
  4. All doors locked using remote control

    (Electronic key transmitter subassembly located outside the detection area*)

  5. Lock sensor not touched → touched
  • *: For details on the detection area of the walk-away/intelligent unlock function, refer to the operation check.

    Click here

(h) Check waveform 4 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

*a

Unlock sensor not touched

*b

Unlock sensor touched

Waveform 4 (reference)

Item

Content

Tester Connection

M67-17 (CLG1) - F1-18 (E)

M67-15 (CLG2) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 50 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors locked
  4. Electronic key transmitter sub-assembly not near vehicle
  5. Unlock sensor not touched → touched

(i) Check waveform 5 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 5 (reference)

Item

Content

Tester Connection

M67-16 (CG1B) - F1-18 (E)

M67-14 (CG2B) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (Electronic key transmitter subassembly located inside the detection area*)

  • *: For details on the detection area of the walk-away/intelligent unlock function, refer to the operation check.

    Click here

(j) Check waveform 6 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 6 (reference)

Item

Content

Tester Connection

M67-16 (CG1B) - F1-18 (E)

M67-14 (CG2B) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 100 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter sub-assembly outside vehicle
  4. All doors locked using remote control

    (Electronic key transmitter subassembly located outside the detection area*)

  • *: For details on the detection area of the walk-away/intelligent unlock function, refer to the operation check.

    Click here

(k) Check waveform 7 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

*a

For 30 seconds after closing any door

*b

At least 30 seconds after closing any door

Waveform 7 (reference)

Item

Content

Tester Connection

F1-8 (CLG5) - F1-18 (E)

F1-9 (CG5B) - F1-18 (E)

M67-11 (CLG7) - F1-18 (E)

M67-10 (CG7B) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

(l) Check waveform 8 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 8 (reference)

Item

Content

Tester Connection

M67-13 (CLG8) - F1-18 (E)

M67-12 (CG8B) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. All doors closed
  4. Trunk door opener switch assembly OFF → ON

(m) Check waveform 9 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

*a

Check ON position signal of switch at reduced intervals

Waveform 9 (reference)

Item

Content

Tester Connection

M67-26 (TSW5) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Trunk door opener switch assembly (opener switch) OFF → ON

Waveform 9 (reference)

Item

Content

Tester Connection

M67-27 (TSW6) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Trunk door opener switch assembly (lock switch) OFF → ON

(n) Check waveform 10 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

*a

Before pressing the lock or unlock switch of the electronic key transmitter subassembly

*b

After pressing the lock or unlock switch of the electronic key transmitter subassembly

Waveform 10 (reference)

Item

Content

Tester Connection

M67-18 (RCO) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside detection area but kept within range of remote control function
  3. Electronic key transmitter sub-assembly lock or unlock switch not pressed → pressed

(o) Check waveform 11 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

*a

Before pressing the lock or unlock switch of the electronic key transmitter subassembly

*b

After pressing the lock or unlock switch of the electronic key transmitter subassembly

Waveform 11 (reference)

Item

Content

Tester Connection

M67-19 (RDAM) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. All doors locked
  3. Electronic key transmitter sub-assembly outside vehicle
  4. Electronic key transmitter sub-assembly outside detection area but kept within range of remote control function
  5. Electronic key transmitter sub-assembly lock or unlock switch not pressed → pressed

*A

Main Body ECU (Multiplex Network Body ECU) with 2 connectors

-

-

*1

Main body ECU (multiplex network body ECU)

-

-

*a

2 connectors

-

-

*A

Main Body ECU (Multiplex Network Body ECU) with 1 connector

-

-

*1

Main body ECU (multiplex network body ECU)

-

-

*a

1 connector

-

-

CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assy.

Click here

(b) Reconnect the connectors to the instrument panel junction block assy.

(c) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Related Data List Item

MB-11 (GND1) - Body ground

-

-

Ground

Always

Below 1 Ω

-

MB-31 (BECU) - Body ground

Input

-

Battery power supply (for CPU)

Always

11 à 14 V

-

F15-6 (FLCY) - Body ground

Input

R - Body ground

Front LH door courtesy light switch assembly input voltage

Front left door closed

10 kΩ minimum

FL Door Courtesy SW

Front left door open

Below 1 Ω

F15-27 (FRCY) - Body ground

Input

BR - Body ground

Front RH door courtesy light switch assembly input voltage

Front right door closed

10 kΩ minimum

FR Door Courtesy SW

Front right door open

Below 1 Ω

MB-13 (LCTY) - Body ground

Input

-

Rear LH door courtesy light switch assembly input voltage

Rear LH door closed

10 kΩ minimum

RL Door Courtesy SW

Rear LH door open

Below 1 Ω

MB-2 (RCTY) - Body ground

Input

-

Rear RH door courtesy light switch assembly input voltage

Rear RH door closed

10 kΩ minimum

RR Door Courtesy SW

Rear RH door open

Below 1 Ω

MB-4 (BCTY) - Body ground

Input

-

Luggage compartment door courtesy light switch input

Luggage compartment door closed

10 kΩ minimum

Back Door Courtesy SW

Luggage compartment door open

Below 1 Ω

(d) Reinstall the main body ECU (multiplex network body ECU) onto the instrument panel junction block assy.

Click here

(e) Measure the voltage and check the pulses according to the value(s) in the table below.

Tester Connection

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Related Data List Item

3D-13 (LSFL) - Body ground

Input

B - Body ground

Front LH door unlock detection switch input

Front LH door locked → unlocked

Pulse generation

(See waveform 1)

FL Door Lock Pos

3D-12 (LSFR) - Body ground

Input

GR - Body ground

Front RH door unlock detection switch input

Front RH door locked → unlocked

Pulse generation

(See waveform 1)

FR Door Lock Pos

3D-14 (LSR) - Body ground

Input

LG - Body ground

Rear LH and rear RH door unlock detection switch input

Rear LH door and rear RH door locked → Rear LH door or rear RH door unlocked

Pulse generation

(See waveform 1)

RL-Door Lock Pos SW

RR-Door Lock Pos SW

F15-6 (FLCY) - Body ground

Input

R - Body ground

Front LH door courtesy light switch input

Front LH door closed → open

Pulse generation

(see waveform 2)

FL Door Courtesy SW

F15-27 (FRCY) - Body ground

Input

BR - Body ground

Rear RH door courtesy light switch input

Front RH door closed → open

Pulse generation

(see waveform 2)

FR Door Courtesy SW

3H-24 (LCTY) - Body ground

Input

BR - Body ground

Rear LH door courtesy light switch input

Rear LH door closed → open

Pulse generation

(see waveform 2)

RL Door Courtesy SW

3A-31 (RCTY) - Body ground

Input

BR - Body ground

Rear RH door courtesy light switch input

Rear RH door closed → open

Pulse generation

(see waveform 2)

RR Door Courtesy SW

3H-34 (BCTY) - Body ground

Input

SB - Body ground

Luggage compartment door courtesy light switch input

Back door closed → open

Pulse generation

(see waveform 2)

Back Door Courtesy SW

3F-29 (BZR) - Body ground

Output

L - Body ground

Remote control buzzer sound output

Procedure:

  1. Engine switch in OFF position
  2. All doors closed
  3. Electronic key transmitter subassembly lock switch not pressed → pressed

Below 1 V → pulse generation

-

(f) Check waveform 1 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 1 (reference)

Item

Content

Tester Connection

3D-13 (LSFL) - Body ground

3D-12 (LSFR) - Body ground

3D-14 (LSR) - Body ground

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Condition

Door locked → unlocked

*a

Door locked

*b

Door unlocked

(g) Check waveform 2 using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

Waveform 2 (reference)

Item

Content

Tester Connection

F15-6 (FLCY) - Body ground

F15-27 (FRCY) - Body ground

3H-24 (LCTY) - Body ground

3A-31 (RCTY) - Body ground

3H-34 (BCTY) - Body ground

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Condition

Door closed → open

*a

Door closed

*b

Door open