Theft Deterrent / Keyless Entry

Precautions

~13min read

PRECAUTION

PRECAUTIONS FOR ELECTRICAL DEVICE INTERFERENCE

CAUTION:

  • Persons with an implanted cardiac pacemaker, cardiac resynchronization therapy defibrillator (CRT-D) or implantable cardioverter defibrillator (ICD) must keep away from the smart key system antennas. Radio waves may affect the proper operation of these devices. If necessary, the entry function can be deactivated. Ask your dealer for information, in particular about the radio wave frequency and the radio wave emission duration. Then consult your doctor to find out whether the entry function should be deactivated.
  • Users of electrical medical equipment other than an implanted cardiac pacemaker, CRT-D or ICD must consult the equipment manufacturer for information on its operation under the influence of radio waves. Radio waves may have unexpected effects on the operation of such equipment.
  • Ask the dealer for information on deactivating the entry function.

    Click here

PRECAUTIONS FOR USING THE TECHSTREAM

(a) When using the Techstream with the engine switch in the OFF position, connect the Techstream to the DLC3 and turn a room light switch ON and OFF at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle starts. Then select the vehicle type manually and enter the following menus: Body Electrical / Smart Key. When using the Techstream, periodically switch a room light switch between ON and OFF at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

PRECAUTIONS WHEN REPLACING PARTS

(a) When replacing any of the following parts, refer to the registration.

Click here

(1) Certification ECU (smart key ECU assembly)

(2) Steering lock ECU (steering lock actuator or upper support assembly)

(3) ID code box (immobiliser code ECU)

(4) Main body ECU (multiplex network body ECU)

(5) Electronic key transmitter sub-assembly

(6) ECM

(b) If the electronic key and TPMS receiver assembly is replaced, it is necessary to register the electronic key transmitter sub-assemblies in the new electronic key and TPMS receiver assembly and perform the registrationand initialization .

PRECAUTIONS FOR THE BATTERY AND THE TRANSMITTER BATTERY BUILT INTO THE ELECTRONIC KEY TRANSMITTER SUB-ASSEMBLY

(a) When the doors are locked, the battery supplies power for radio wave transmission. The battery may discharge if the vehicle is left parked for a long period. If the vehicle will not be used for a long time, disconnect the cable from the negative (-) battery terminal, switch to the transmitter battery saver mode, or deactivate the Smart Key System (for Entry Function).

HINT:

  • Refer to the following procedures to disable the smart key system (for entry function).

    Click here

  • Transmitter battery saving function.

    Click here

(b) When the doors are locked and an electronic key transmitter is within the detection area of an electronic key antenna, the transmitter battery may discharge due to periodic communication between the electronic key transmitter and the vehicle. If the vehicle is not used for a long period of time, keep the key outside the vehicle (more than 2 m (6.56 ft) away).

PRECAUTIONS FOR THE ELECTRONIC KEY TRANSMITTER

(a) The electronic key transmitter is a precision instrument. Be sure to observe the following:

(1) Do not subject the electronic key transmitter to strong impacts.

(2) Do not expose the electronic key transmitter to high temperatures for long periods of time.

(3) Do not use an ultrasonic cleaner to clean the electronic key transmitter.

(4) Do not use the electronic key transmitter near magnets or magnetic objects.

(5) Do not place the electronic key transmitter near magnetic equipment, such as digital audio players, induction cookers, medical devices that emit low-frequency electromagnetic waves, etc.

(6) Do not attach any stickers to the electronic key transmitter.

(7) Do not disassemble the electronic key transmitters.

(8) The mechanical key should only be used in an emergency, such as when the transmitter battery is discharged.

PRECAUTIONS WHEN INSPECTING THE SMART KEY SYSTEM (for entry function)

(a) General precautions for the smart key system (for entry function):

(1) Always keep the electronic key transmitter with you.

(b) The smart key system (for entry function) may not operate normally, or the key detection area may decrease, in the following situations:

(1) The transmitter battery is discharged.

(2) Television transmission stations, power plants, broadcasting stations, gas stations or other areas with strong radio waves or electrical noise are nearby.

(3) Devices with remote communication functions, such as walkie-talkies, mobile phones, cordless phones, digital audio players, portable game systems, etc., are being carried together with the electronic key transmitter.

(4) The electronic key transmitter is covered by or in contact with metal objects, such as coins or certain types of cards.

(5) Metallic film is applied to the rear window glass.

(6) A radio wave type keyless entry system or remote control system is used nearby.

(7) The electronic key transmitter of another vehicle is nearby.

(8) The electronic key transmitter is placed near equipment that generates high voltage or electrical noise.

(9) The electronic key transmitter is located near an electronic device such as a battery charger.

(c) Operating range of the smart key system (for entry function):

(1) Due to the vehicle body design, there are certain areas where system operation is difficult.

(2) Even if the electronic key transmitter is within the detection area outside the vehicle, it may not be detected correctly if it is near a window, a door handle, or the center of the bumper.

(3) Even if an electronic key transmitter is within the detection area inside the vehicle, it may not be detected correctly if it is on the instrument panel, in the glove box, or on the floor.

(4) Depending on the orientation in which the electronic key transmitter is held, it may not operate correctly.

(d) Since weak radio waves are emitted by the electronic key transmitter, if you use a cardiac pacemaker, be sure to read the cardiac pacemaker manufacturer's instructions.

(e) The smart key system (for entry function) will not operate under the following conditions:

(1) The procedure to disable the smart key system (for entry function) has been performed.

(2) There is no battery in the transmitter, or the transmitter battery is discharged (the LED on the electronic key transmitter does not flash when a switch on the electronic key transmitter is pressed).

PRECAUTIONS FOR THE ENTRY UNLOCK FUNCTION

(a) When unlocking the doors, be sure to grip the entire outside door handle while making contact with the sensor on the inner part of the handle. Pull the handle after confirming that the door is unlocked.

(b) If the entire outside door handle is gripped while wearing gloves, unlocking may be delayed or may not occur.

(c) When performing an entry unlock operation, make sure that one of the doors is unlocked before pulling an outside door handle to open the door.

(d) When attempting to open a door suddenly or immediately after entering an exterior detection area of the vehicle, the doors may fail to unlock. In this case, the system automatically performs the door unlock operation 4 times. However, if an outside door handle assembly is pulled at this time, the door may not unlock due to mechanical reasons. If the door does not unlock, return the outside door handle assembly to its original position and pull the handle again after confirming that the door is unlocked.

(e) If the electronic key transmitter sub-assembly is too close to the outside door handle assembly, it may not be possible to unlock the door using the unlock-on-opening function.

(f) If an electronic key transmitter sub-assembly is within the exterior detection area of the vehicle, the door may be unlocked even when a person other than the one carrying the electronic key transmitter sub-assembly grasps the outside door handle assembly. However, doors other than the door for which the corresponding code is detected cannot be unlocked (if the electronic key transmitter sub-assembly is within the exterior detection area of the driver's side door and the front left outside door handle assembly is held, the doors can be unlocked. However, if the front right outside door handle assembly is held, the doors cannot be unlocked).

(g) After a remote door lock, a manual door lock, or a key-linked door lock operation performed with an electronic key transmitter sub-assembly located inside a detection area or near the vehicle, an unlock-on-opening operation cannot be performed. Therefore, when a remote door lock operation is performed near a window or door handle, the unlock-on-opening function may not operate. To unlock the doors, use the remote door unlock function.

(h) If a door is not opened after unlocking, the doors will automatically lock after approximately 60 seconds*.

(i) If an electronic key transmitter sub-assembly is within an exterior detection area of the vehicle and a large amount of water is applied to the outside door handle assembly, such as from car washing or heavy rain, the sensor may react and the unlock-on-opening operation may be performed. However, the doors will automatically lock after approximately 60 seconds if no door is opened*.

(j) If the electronic key transmitter sub-assembly is carried together with the electronic key transmitter sub-assembly of another vehicle equipped with a smart key system, and the outside door handle assembly is held, the time before the door unlocks through the unlock-on-opening operation may be longer than usual.

HINT:

*: When the automatic locking function operates after an unlock-on-opening operation, if an electronic key transmitter sub-assembly is detected in the cabin, the doors will be unlocked using the door ajar warning function.

PRECAUTIONS FOR THE LOCK-ON-OPENING FUNCTION

(a) When performing a lock-on-opening operation, if the lock sensor on the outside door handle assembly is touched too quickly, the door may not lock.

(b) If the electronic key transmitter sub-assembly is brought near the inside of the vehicle (window, outside door handle assembly), the lock-on-opening function may not operate. Also, the key reminder warning buzzer may sound and the unlock-on-entry operation may stop functioning. In this case, move the electronic key transmitter sub-assembly away from the inside of the vehicle (window, front outside door handle assembly), perform a lock-on-opening operation, then perform an unlock-on-opening operation.

(c) If the electronic key transmitter sub-assembly is being carried and a lock operation is performed from the driver's door while the driver's door is open (ajar), the door ajar indicator does not operate.

(d) If the electronic key transmitter sub-assembly is left on the instrument panel, in the glove box or on the floor, the key left-behind warning function may not operate and the electronic key transmitter sub-assembly may be locked inside the vehicle when a door lock operation is performed. Always keep the electronic key transmitter sub-assembly with you.

(e) The unlock-on-opening operation cannot be performed for approximately 3 seconds after a door lock operation is performed, such as the lock-on-opening operation or remote lock operation.

(f) When checking the operation of the lock-on-open function repeatedly, it can only be performed twice in succession according to the settings. To perform this operation 3 or more times in succession, the doors must be unlocked once (any unlock operation is acceptable). However, this applies only to the lock-on-open function. Other door lock functions, such as the remote door lock function, can be performed in succession.