How to Use Troubleshooting
PRECAUTION / NOTICE / HINT
HINT:
- Follow these procedures to troubleshoot the smart key system (for open function).
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
HINT:
- When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
- Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
- The following 5 elements are essential for analyzing the problem:
What?
Vehicle model, system name
When?
Date, time, frequency of occurrence, whether the problem appeared recently or has been occurring for a long time
Where?
If the problem occurs at a specific location
What were the conditions?
Whether the doors are locked or unlocked, whether the ignition switch is in the ON position, whether the engine is running
How did it happen?
Symptoms of the problem*
- *: Be sure to ask the customer to describe the following points in very precise detail: the vehicle operating conditions, the environment, and the problem. Then check the DTCs.
- If the lock/unlock on open function does not operate for all doors.
- If the lock on open function does not operate.
- If the unlock on open function does not operate.
- If both the lock and unlock on open functions do not operate.
- If the remote lock and unlock functions do not operate.
- If there is no power supply, even when the engine switch is pressed (the engine switch does not move to the ON (ACC) position).
- If the engine does not start using the push-button start function.
- If the exterior buzzers do not sound.
- If an attempt was made to start the engine by holding the electronic key transmitter close to the engine switch and pressing the engine switch.
- If the interior buzzers do not sound.
- If the steering wheel does not unlock.
- Any other details about the problem.
- If radio wave interference is suspected, be sure to ask the customer to describe the following vehicle operating conditions, environment and problem as precisely as possible.
- Locations where the system does not operate (such as near television broadcast stations, large video screens, remote garage door opener systems, remote security cameras, home security systems, etc.).
- Specific occasions when the system does not operate: If the symptoms occurred immediately after purchase or only a short time after. If the symptoms occurred when the electronic key transmitter was near the vehicle (electronic key antenna).
- If the system only fails when near specific vehicles (radio wave interference may be coming from the remote systems of other vehicles).
- If the system operates intermittently.
- If the electronic key transmitter is grouped with other items.
- If the electronic key transmitter is carried with other electronic devices, such as mobile phones, computers, portable music players, other electronic key transmitters, etc. (keep the electronic key transmitter at least 0.1 m (0.328 ft) away from such items).
- Where the electronic key transmitter is kept when not in use: If the electronic key transmitter is placed within 1 m (3.28 ft) of items such as televisions, DVD recorders, induction cooktops, rice cookers, dishwashers, modems, mobile phones, computers, microwave ovens, desk lamps or floor lamps, cordless phones, etc.
- If there are electronic devices in the vehicle that transmit radio waves.
- When the transmitter battery was last replaced. The transmitter battery can be partially checked using the "Key Low Battery" item in the Data List.
Click here
.gif)
- If the steering wheel does not unlock.
- If the customer has installed any accessories (anti-theft devices, remote fog lights, etc.) on the vehicle.
- *: Be sure to ask the customer to describe the following points in very precise detail: the vehicle operating conditions, the environment, and the problem. Then check the DTCs.
|
CHECK BATTERY
(a) Measure the battery voltage.
Standard voltage:
11 à 14 V
If the voltage is below 11 V, charge or replace the battery before proceeding to the next step.
|
CHECK CAN COMMUNICATION SYSTEM FUNCTION*
(a) Using the Techstream, check for DTCs related to the CAN communication system.
Click here
![]()
Result:
Result | Proceed to |
|---|---|
No CAN system DTCs are output |
A |
CAN-related DTCs are output |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK GAUGE AND METER SYSTEM*
(a) Using the Techstream, check that the gauge and meter system operates correctly.
HINT:
If the certification ECU (smart key ECU assembly) receives a vehicle speed signal in error, communication between the Techstream and the vehicle will fail. Be sure to check the "Vehicle Speed Meter" item displayed in the Data List to confirm that the vehicle speed is not abnormal.
Result:
Result | Proceed to |
|---|---|
No vehicle speed signal is received in error |
A |
A vehicle speed signal is received in error |
B |
| B | GO TO METER/GAUGE SYSTEM |
|
CHECK LIN COMMUNICATION SYSTEM COMMUNICATION FUNCTION*
(a) Using the Techstream, check for DTCs related to the LIN communication system.
Click here![]()
Result:
Result | Proceed to |
|---|---|
LIN system DTCs are not output |
A |
LIN-related DTCs are output |
B |
| B | GO TO LIN COMMUNICATION SYSTEM |
|
CHECK WIRELESS DOOR LOCK SYSTEM OPERATION*
(a) Using the Techstream, check for any DTCs of the wireless door lock system.
Click here![]()
Result:
Result | Proceed to |
|---|---|
No wireless door lock system DTCs are output |
A |
Wireless door lock system DTCs are output |
B |
| B | GO TO WIRELESS DOOR LOCK CONTROL SYSTEM |
|
CHECK DTCs*
(a) Check the DTCs.
Body Electrical > Smart Key > Trouble CodesResult:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
DTCs related to the steering lock system are output |
B |
Immobilizer system (with smart key system) DTCs are output |
C |
Smart key system (entry function) DTCs are output |
D |
| B | GO TO STEERING LOCK SYSTEM |
| C | GO TO IMMOBILIZER SYSTEM |
| D | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
SYMPTOM TROUBLESHOOTING TABLE
(a) Refer to the Symptom Troubleshooting Table.
Click here
![]()
Result:
Result | Proceed to |
|---|---|
The malfunction is not listed in the Problem Symptoms Table |
A |
The malfunction is listed in the Problem Symptoms Table |
B |
| B | ADJUST, REPAIR OR REPLACE ACCORDING TO THE SYMPTOM TABLE |
|
GENERAL ANALYSIS AND TROUBLESHOOTING*
(a) Operation Check
Click here
![]()
(b) Data List/Active Test
Click here
![]()
(c) ECU terminals
Click here
![]()
|
REPAIR OR REPLACEMENT
|
CHECK DTCs*
(a) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs(b) Check DTCs.
Body Electrical > Smart Key > Trouble CodesResult:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
Smart key system (entry function) DTCs are output |
B |
| A | END |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |