Theft Deterrent / Keyless Entry

Customizable Parameters

15steps
~90min
4/5difficulty
Done 0 of 15

CUSTOMIZABLE PARAMETERS

CUSTOMIZE SMART KEY SYSTEM (for entry function)

HINT:

The following items can be customized:

NOTICE:

  • When the customer requests a change to a function, first make sure that the function can be customized.
  • Record the initial settings before performing customization.

(a) Customizing using the Techstream

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch to ON (IG).

(3) Turn on the Techstream.

(4) Select the following menus: Customize Setting / Wireless Door Lock, Answer Back Indicator or Smart Key / Entry.

(5) Select the setting by referring to the table below.

Remote Central Door Lock

Tester display

Description

Default setting

Setting

ECU

Wireless Control

Function that enables or disables the wireless door lock system.

ON

0 : OFF, 1 : ON

Main body ECU (multiplex network body ECU)

Hazard Answer Back

Function that flashes the hazard warning lights once when the doors are locked by the entry lock function, and twice when the doors are unlocked by the entry lock function.

ON

0 : OFF, 1 : ON

Main body ECU (multiplex network body ECU)

Open Door Warning

Function that sounds a buzzer when the lock sensor on the outside door handle assembly is touched to perform the entry lock function while a door is open.

ON

0 : OFF, 1 : ON

Main body ECU (multiplex network body ECU)

Auto Lock Time

Function that sets the time between unlocking and automatic relocking of the doors.

60 s

00: 30 s, 01: 60 s, 10: 120 s

Main body ECU (multiplex network body ECU)

Wireless Buzzer Resp

Function that enables/disables the response of the wireless door lock buzzer*1.

ON

0 : OFF, 1 : ON

Main body ECU (multiplex network body ECU)

Wireless Buzzer Vol

Function that adjusts the volume of the wireless door lock buzzer*1.

Level5

0000: Level7, 0001: Level6, 0010: Level5, 0011: Level4, 0100: Level3, 0101: Level2, 0110: Level1, 0111: Level0

Main body ECU (multiplex network body ECU)

  • *1: with Toyota Safety Sense P system
Alarm

Tester display

Description

Default setting

Setting

ECU

Key Low Battery Warning

Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is in OFF after having been in ON (IG) for at least 20 minutes.

ON

0 : OFF, 1 : ON

Certification ECU (Smart Key ECU Assy)

Entry / Smart Key

Tester display

Description

Default setting

Setting

ECU

Park Wait Time

Function that sets the time (lock confirmation time) during which the front door can not be unlocked using the outside door handle assembly after an entry lock operation is performed.

2,5s

00 : 0,5 s, 01 : 1,5 s, 10 : 2,5 s, 11 : 5 s

Certification ECU (Smart Key ECU Assy)

Back Door Opening Operation

Function that determines the operation of the trunk opener switch (opener switch) required to open the trunk lid when the driver is carrying the electronic key transmitter sub-assembly.

Long

00: Long, 01: Twice, 10: OFF

Certification ECU (Smart Key ECU Assy)

Door Unlock Mode2

Function that determines which doors are unlocked by the unlock-on-open function.

Driver

0: All, 1: Driver

Certification ECU (Smart Key ECU Assy)

Touch Activation Over Threshold

Function that limits the number of consecutive times the unlock-on-open function can be used. When set to Not Active, the unlock-on-open function can be used an unlimited number of consecutive times.

Active

0: Active, 1: Not Active

Certification ECU (Smart Key ECU Assy)

(b) Customization using the multi-information display (for type with radio and display)

(1) Turn the engine switch to ON (IG).

(2) Select the following menus: MENU / Settings / Vehicle / Vehicle Customization / Door Lock Setting.

(3) Select the setting by referring to the table below.

Tester display

Default setting

Content

Setting

Remote 2-Press Unlock

ON

Function that unlocks the driver's door when the transmitter unlock switch is pressed once, and unlocks all doors when it is pressed twice. If set to OFF, pressing the unlock switch once unlocks all doors.

ON or OFF

Auto Relock Timer

60 s

Function that determines the time between unlocking and automatic relocking of the doors.

120 s, 60 s, 30 s or OFF

Lock/Unlock Feedback Lights

ON

This function flashes the hazard lights once when the doors are locked using the remote control, and twice when the doors are unlocked using the remote control.

ON or OFF

Lock/Unlock Feedback Tone

5

Remote door lock buzzer volume

Off, 1, 2, 3, 4, 5, 6 or 7

(c) Unlock-on-open mode change function (manual operation)

(1) The following unlock-on-open modes can be selected using the unlock-on-open mode change function.

  • All-doors unlock mode: When the unlock sensor on a front outside door handle assembly is touched, all doors are unlocked simultaneously.
  • Driver's door unlock mode: When the unlock sensor on the front left outside door handle assembly is touched, only the driver's door is unlocked. If another outside door handle assembly is touched, all doors are unlocked simultaneously.

(2) For customization by manual operation:

  1. Set the engine switch to OFF.
  2. Make sure the LED on the electronic key transmitter sub-assembly does not light up, and hold the lock and unlock switches on the electronic key transmitter sub-assembly for at least 5 seconds while the electronic key transmitter sub-assembly is in the exterior detection area.
  3. Check the current setting.

    HINT:

    • The mode toggles from all-doors unlock mode to driver's door unlock mode, then back to all-doors unlock mode.
    • The automatic response operation (remote control buzzer*, buzzer in the instrument cluster) for each mode is shown in the table below.

      Currently selected mode

      Automatic response (remote control buzzer)*

      Automatic response (buzzer in the instrument cluster)

      All-doors unlock mode

      The buzzer sounds twice (short beeps)

      The buzzer sounds once

      Driver's door unlock mode

      The buzzer sounds 3 times (short beeps)

      The buzzer sounds once

    • *: with Toyota Safety Sense P system
  4. Release the lock and unlock switches on the electronic key transmitter sub-assembly.
  5. Make sure the LED on the electronic key transmitter sub-assembly does not light up, and hold the lock and unlock switches on the electronic key transmitter sub-assembly for at least 5 seconds to change the mode.

    HINT:

    Repeat the procedure as many times as necessary to select the desired mode.

  6. Unlock the doors using the remote function, then open a door.

(d) Open disable function (manual operation)

HINT:

While the smart key system is deactivated, the doors can be locked and unlocked using the remote control, and the engine can be started by holding the electronic key transmitter close to the engine switch.

(1) The following functions are disabled when the smart key system is deactivated.

  1. Open unlock/lock functions
  2. Push-button start function
  3. Key lock-out prevention function
  4. Open warning functions

(2) When the smart key system is deactivated by manual operation:

  1. Make sure the following conditions are met:
    • The engine switch is in OFF position.
    • The driver's door is closed.
    • The driver's door is unlocked.

(3) Press the unlock switch on the electronic key transmitter sub-assembly.

(4) Open the driver's door within 5 seconds after completing the above operation (driver's door: closed → open).

(5) With the driver's door open, press the unlock switch on the electronic key transmitter sub-assembly twice within 5 seconds after completing the above step.

NOTICE:

If the driver's door is closed before or during pressing of the unlock switch, the open disable setting mode stops.

(6) Perform the following procedure within 30 seconds after completing the above step.

  1. Close and open the driver's door twice (driver's door: open → closed → open → closed → open).
  2. With the driver's door open, press the unlock switch on the electronic key transmitter sub-assembly twice.

    NOTICE:

    If the driver's door is closed before or during pressing of the unlock switch, the open disable setting mode stops.

  3. Close and open the driver's door (driver's door: open → closed → open).

(7) Close the driver's door within 5 seconds (driver's door: open → closed).

(8) Make sure that the remote buzzer sounds twice (short beeps) to confirm that the smart key system has been deactivated.

(9) Perform the following procedure to change the smart key system from deactivated to activated.

  1. Perform the procedure to deactivate the smart key system again.
  2. Make sure that the remote buzzer sounds once (short beep) to confirm that the smart key system has been reactivated.

    HINT:

    • The system changes from deactivated to activated each time the manual system deactivation procedure is performed.
    • The buzzer sounds twice when the system changes from activated to deactivated, and sounds once when the system changes from deactivated to activated.