Theft Deterrent / Keyless Entry

The exterior entry buzzer does not sound

~7min read

DESCRIPTION

The smart key system (for the entry function) uses the remote door lock buzzer to activate various exterior warnings of the vehicle. When the conditions for each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via the CAN communication system, and the buzzer sounds.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • The Smart Key System (for Access Function) uses a LIN communication system and a CAN communication system. Check the communication function by following the procedure described in HOW TO USE TROUBLESHOOTING MODE. Troubleshoot the Smart Key System (for Access Function) after confirming that the communication systems operate normally.

    Click here

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Before replacing the certification ECU (smart key ECU assembly) or the main body ECU (multiplex network body ECU), refer to the Precaution section.

    Click here

  • After repair, confirm that no DTCs are output.

PROCEDURE

  1. INSPECT WIRELESS DOOR LOCK CONTROL SYSTEM

(a) Check whether the function operates normally.

Click here

Result:

Result

Proceed to

Remote door lock function operates normally

A

Remote door lock function does not operate normally

B

B

REFER TO SYMPTOM TROUBLESHOOTING TABLE

A
  1. READ THE VALUE USING TECHSTREAM (EACH UNLOCK DETECTION SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Pos

Front Right Door Unlock Detection Switch Signal

UNLOCK or LOCK

UNLOCK: Front right door unlocked.

LOCK: Front right door locked.

-

FL Door Lock Pos

Front Left Door Unlock Detection Switch Signal

UNLOCK or LOCK

UNLOCK: Front left door unlocked.

LOCK: Front left door locked.

-

RR-Door Lock Pos SW

Rear Left and Right Door Unlock Detection Switch Signal

ON or OFF

ON: Rear left and right doors unlocked

OFF: Rear left and right doors locked

-

RL-Door Lock Pos SW

Rear Left and Right Door Unlock Detection Switch Signal

ON or OFF

ON: Rear left and right doors unlocked

OFF: Rear left and right doors locked

-

Body Electrical > Main Body > Data List

Tester display

FR Door Lock Pos

FL Door Lock Pos

RR-Door Lock Pos SW

RL-Door Lock Pos SW

OK:

The Techstream display changes correctly according to the lock/unlock operation.

NG

GO TO LIGHTING SYSTEM (go to door unlock detection switch circuit)

OK
  1. PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS BUZZER)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test by following the instructions shown on the Techstream screen.

Body Electrical > Main Body > Active Test

Tester display

Item

Control Range

Diagnostic Note

Wireless Buzzer

Remote Door Lock Buzzer

OFF / ON

-

Body Electrical > Main Body > Active Test

Wireless Buzzer

Result:

Result

Proceed to

The remote door lock buzzer does not sound

A

The remote door lock buzzer sounds

B

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

A
  1. INSPECT THE REMOTE DOOR LOCK BUZZER

(a) Disconnect connector A24 from the remote door lock buzzer.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch to ON (IG).

(d) Turn on the Techstream.

(e) Select the following menu items: Body Electrical / Main Body / Active Test.

(f) Perform the Active Test by following the instructions shown on the Techstream screen.

Body Electrical > Main Body > Active Test

Tester display

Item

Control Range

Diagnostic Note

Wireless Buzzer

Remote Door Lock Buzzer

OFF / ON

-

Body Electrical > Main Body > Active Test

Wireless Buzzer

(g) While performing the Active Test, measure the voltage between the terminals of the remote door lock buzzer.

Standard voltage:

Tester Connection

Condition

Specified Condition

A24-1 (B) - A24-2 (E)

Active Test remote control buzzer activation

Pulse generation

(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)

Active Test remote control buzzer deactivation

Below 1 V

*a

Front view of wire harness side connector

(to the remote door lock buzzer)

OK

REPLACE THE REMOTE DOOR LOCK BUZZER

NG
  1. INSPECT THE WIRE HARNESS AND CONNECTOR (REMOTE DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assy.

Click here

(b) Disconnect connector A24 from the remote door lock buzzer.

(c) Reconnect connector 3F of the instrument panel junction block assembly.

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A24-1 (B) - MB-21 (BZR)

Always

Below 1 Ω

A24-2 (E) - Body ground

Always

Below 1 Ω

A24-1 (B) or MB-21 (BZR) - Body ground

Always

10 kΩ minimum

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG
  1. INSPECT THE WIRE HARNESS AND CONNECTOR (REMOTE DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 3F connector from the instrument panel junction block assembly.

(b) Disconnect connector A24 from the remote door lock buzzer.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A24-1 (B) - 3F-29

Always

Below 1 Ω

A24-1 (B) or 3F-29 - Body ground

Always

10 kΩ minimum

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR