Theft Deterrent / Keyless Entry

Data List / Active Test

~26min read

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

  • In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.
  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Smart Key, Main Body, Power Source Control or Combination Meter / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

D-Door Touch Sensor

Driver door touch sensor (unlock sensor)*

ON or OFF

ON: Driver door touch sensor (unlock sensor) touched

OFF: Driver door touch sensor (unlock sensor) not touched

  • Displays whether the unlock sensor is ON or OFF (even if the sensor is touched and held, "ON" is displayed only momentarily).
  • Use this Data List item to determine whether there is a malfunction in the unlock sensor when the walk-away unlock function does not operate.

P-Door Touch Sensor

Front passenger door touch sensor (unlock sensor)*

ON or OFF

ON: Front passenger door touch sensor (unlock sensor) touched

OFF: Front passenger door touch sensor (unlock sensor) not touched

  • Displays whether the unlock sensor is ON or OFF (even if the sensor is touched and held, "ON" is displayed only momentarily).
  • Use this Data List item to determine whether there is a malfunction in the unlock sensor when the walk-away unlock function does not operate.

D-Door Trigger Switch

Driver door touch sensor (lock sensor)*

ON or OFF

ON: Driver door touch sensor (lock sensor) touched

OFF: Driver door touch sensor (lock sensor) not touched

  • Displays whether the lock sensor is ON or OFF (even if the sensor is touched and held, "ON" is displayed only momentarily).
  • Use this Data List item to determine whether there is a malfunction in the lock sensor when the walk-away lock function does not operate.

P-Door Trigger Switch

Front passenger door touch sensor (lock sensor)*

ON or OFF

ON: Front passenger door touch sensor (lock sensor) touched

OFF: Front passenger door touch sensor (lock sensor) not touched

  • Displays whether the lock sensor is ON or OFF (even if the sensor is touched and held, "ON" is displayed only momentarily).
  • Use this Data List item to determine whether there is a malfunction in the lock sensor when the walk-away lock function does not operate.

Tr/B-Door Lock SW

Trunk door opener switch assembly (lock switch)

ON or OFF

ON: Back door opener switch assembly (lock switch) pressed

OFF: Back door opener switch assembly (lock switch) not pressed

  • Displayed whether the back door opener switch assembly (lock switch) is ON or OFF.
  • Use this Data List item to determine whether there is a malfunction in the switch when the back door lock function does not operate.

Tr/B-Door Unlock SW

Trunk door opener switch assembly (opener switch)

ON or OFF

ON: Trunk Opener Switch Assembly (Trunk Opener Switch) pressed

OFF: Trunk Opener Switch Assembly (Trunk Opener Switch) not pressed

  • Displayed regardless of whether the Trunk Opener Switch Assembly (Trunk Opener Switch) is in the ON or OFF position.
  • Use this Data List item to determine whether there is a switch malfunction when the trunk opener function does not operate.

Unmatched Vehicle-ID

Key No. (Correct or Incorrect)

Yes or No

Yes: Communication malfunction

No: Communication normal

The Vehicle-ID registered in the vehicle and the Vehicle-ID registered in the key are different (if a key for another vehicle is brought into the vehicle's exterior detection area while the doors are locked, "YES" is displayed for the "Unmatched Vehicle-ID" Data List item).

Other possible causes:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • A communication error due to radio wave interference.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

No Response

Communication Response

Yes or No

Yes: Communication malfunction

No: Communication normal

The Vehicle-ID codes registered in the vehicle and in the electronic key transmitter sub-assembly match, but there is no response from the electronic key transmitter sub-assembly. (If the electronic key transmitter sub-assembly is not in the detection area, or if the transmitter battery is discharged so that no matching code is detected when the lock switch or engine switch is pressed, etc., "Yes" is displayed for the "No Response" Data List item. In addition, if there is radio wave interference in the LF band the vehicle uses for transmission, or in the RF band the electronic key transmitter sub-assembly uses for transmission, "Yes" may be displayed for the "No Response" Data List item.)

Other possible causes:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Unmatch Code or Form

Code Format (Incorrect or Correct)

Yes or No

Yes: Communication malfunction

No: Communication normal

There is an error in the data transmitted by the electronic key transmitter sub-assembly. (If there is radio wave interference in the RF band the electronic key transmitter sub-assembly uses for transmission, "Yes" may be displayed for the "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" Data List items.)

Other possible causes:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Key Low Battery

Transmitter Battery Discharged

Yes or No

Yes: Transmitter battery discharged

No: Transmitter battery not discharged

The electronic key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it transmits. "Yes" is displayed for the "Key Low Battery" Data List item when the voltage information indicates a value of 2.2 V or less. This Data List item must be checked when the electronic key transmitter sub-assembly is at cabin temperature (for example, at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).

Power Save Cnt 10 Min.

Number of times the power save control is activated due to the electronic key transmitter sub-assembly being in the detection area for at least 10 minutes

0 à 255

Within a range of 0 to 255

If the electronic key transmitter sub-assembly is in the vehicle's exterior detection area, communication between the vehicle and the electronic key transmitter sub-assembly occurs frequently, which increases the power consumption of the transmitter battery. To prevent the transmitter battery from becoming fully discharged, if the electronic key transmitter sub-assembly is left within the detection area for at least 10 minutes, the smart key system automatically deactivates the exterior detection area where the electronic key transmitter sub-assembly is located. If the doors are locked/unlocked using the remote control or by using the mechanical key function, the system resumes operation.

Power Save Cnt 5 Days

Number of times power save control 1 (stops periodic signal transmission outside the vehicle) is activated due to the engine not being started for at least 5 days

0 à 255

Within a range of 0 to 255

-

Power Save Cnt 14 Days

Number of times power save control 2 (front passenger side outside door handle assembly lock/unlock sensor disabled) is activated due to the engine not being started for at least 14 days

0 à 255

Within a range of 0 to 255

-

# Codes

Number of DTCs

0 à 255

Number of stored DTCs displayed

-

ID Code Difference(Resp)

ID Code (Incorrect or Correct)

Yes or No

Yes: Communication malfunction

No: Communication normal

The ID code registered in the vehicle and the ID code registered in the electronic key transmitter sub-assembly are different. (If there is radio wave interference in the RF band the electronic key transmitter sub-assembly uses for transmission, "Yes" may be displayed for the "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" Data List items.)

Other possible causes:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

C Code Difference

Request Code (Incorrect or Correct)

Yes or No

Yes: Communication malfunction

No: Communication normal

The electronic key transmitter sub-assembly transmits a response code in reply to the request code from the vehicle, but the response code is incorrect. (If there is electrical radio wave interference in the RF band the electronic key transmitter sub-assembly uses for transmission, "Yes" may be displayed for the "Unmatch Code or Form", "No Response", "ID Code Difference (Resp)" and "C Code Difference" Data List items.)

Other possible causes:

  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

ID Code Difference

Remote ID Code (Incorrect or Correct)

Yes or No

Yes: Communication malfunction

No: Communication normal

The ID code registered in the vehicle and the ID code registered in the electronic key transmitter sub-assembly are different. (If a remote control ID code different from those registered for the other registered electronic key transmitter sub-assemblies is detected, "Yes" is displayed for the "ID Code Difference" item in the Data List. If a remote control signal from the electronic key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for the "ID Code Difference (Resp)" item in the Data List.)

Other possible causes:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • A communication error due to external noise (RF).
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Immobiliser

Immobiliser system state determined by the certification ECU

Set or Unset

Set: Immobiliser activated (engine start disabled) (engine switch in OFF position)

Unset: Immobiliser deactivated (engine start allowed) (engine switch in ON (ACC) or ON (IG) position)

When the immobiliser system does not change to the disabled state, this item can be used to determine whether the cause is the certification ECU or the ID code box.

Different Rolling Code

Rolling code (incorrect or correct)

Yes or No

Yes: Communication malfunction

No: Communication normal

The rolling code registered in the vehicle and the rolling code registered in the electronic key transmitter sub-assembly are different.

Other possible causes:

  • The electronic key transmitter sub-assembly switch is pressed at least 100 times in a location where radio waves cannot reach the vehicle.
  • A communication error due to external noise (RF).
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

S Code Check

S Code Check Result

OK or NG

OK: S code verification result normal

NG: S code verification result abnormal

Problems may be caused by the following conditions:

  • Registration has not been performed for the Smart Key System ECU (smart key ECU assembly) or the ID Code Box (Immobiliser Code ECU).
  • In case of malfunction of the certification ECU (smart key ECU assembly) or the ID code box (immobiliser ECU).

L Code Check

L Code Check Result

OK or NG

OK: L code verification result normal

NG: L code verification result abnormal

Problems may be caused by the following conditions:

  • Registration has not been performed for the ID Code Box (Immobiliser Code ECU) or the steering lock ECU (steering lock actuator assembly or upper support).
  • Possible malfunctions in the ID code box (immobiliser ECU) or the steering lock ECU (steering lock actuator or steering column upper support assembly).

Unlock Request Receive

Steering unlock control state transmitted by the certification ECU (smart key ECU assembly)

OK or NG

OK: Smart Key System ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds after the engine switch is set to ON (ACC) or ON (IG), or the engine start command is executed)

NG: Smart Key System ECU (smart key ECU assembly) does not send steering unlock command (engine switch is not set to ON (ACC) or ON (IG), and engine start operation is not performed)

-

Lock Request Receive

Steering lock control state transmitted by the certification ECU (smart key ECU assembly)

OK or NG

OK: Smart Key System ECU (smart key ECU assembly) sends steering lock command (within 10 seconds after a door is opened with the shift lever in P and the engine switch in OFF)

NG: Smart Key System ECU (smart key ECU assembly) does not send steering lock command (no door opened with the shift lever in P and the engine switch in OFF)

-

S Code Check(Past)

S Code Verification Result (Past)

OK or NG (Past)

OK: Normal check result (Past)

NG (Past): Abnormal verification result (Past)

-

L Code Check(Past)

L Code Verification Result (Past)

OK or NG (Past)

OK: Verification confirmed (past)

NG (Past): Verification not confirmed (past)

-

Steering Lock

State of the steering lock ECU (steering lock actuator or upper support assembly) determination that the steering is locked

Set or Unset

Set: Steering locked

Unset: Steering unlocked

If this item displays "Unset", the steering is not locked.

Steering Unlock

State of the steering lock ECU (steering lock actuator or upper support assembly) determination that the steering is unlocked

Set or Unset

Set: Steering unlocked

Unset: Steering locked

If this item displays "Unset", the steering is not unlocked (the engine cannot be started).

B Code Difference

B code mismatch

Yes or No

Yes: Communication malfunction

No: Communication normal

-

B Code

B Code Registration Status

Regd or No Regd

Regd: B code registered correctly

No Regd: B code not registered correctly

-

Door Unlock Mode2

Door Unlock Mode

All or Driver

Customised setting displayed

-

Ignition Available Area

Ignition Available Area

Front or All

Customised setting displayed

-

Parking Wait Time

Parking Wait Time

0.5 s, 1.5 s, 2.5 s or 5 s

Customised setting displayed

-

B-Dr Opening Operation

Back Door Opening Operation

Long, Twice or OFF

Customised setting displayed

-

Touch Activation Over Threshold

Consecutive Opening Lock Operation

Active or Not Active

Customised setting displayed

-

Wireless Signal Encryption Support

Remote Control Signal Encryption Support

Yes or No

Yes: Remote control signal encryption support

No: Remote control signal encryption not supported

-

Key Low Battery Warning

Transmitter Low Battery Warning

ON or OFF

Customised setting displayed

-

Engine Start Indicator

The unlock indicator light comes on

ON or OFF

Customised setting displayed

-

Number of Registered Key Codes

Number of registered electronic key transmitter sub-assemblies:

0 à 8

Number of registered electronic key transmitter sub-assemblies:

Up to 7 electronic key transmitter sub-assemblies can be registered.

Short in Front Passenger Side Door Oscillators Circuit (Hist)

Short in front passenger door electronic key antenna circuit (history)

OK or NG (Hist)

OK: Electronic key antenna circuit normal at front passenger door

NG (Hist): Electronic key antenna circuit abnormal at front passenger door

-

Short in Driver Side Door Oscillators Circuit (Hist)

Short in driver door electronic key antenna circuit (history)

OK or NG (Hist)

OK: Electronic key antenna circuit normal at driver door

NG (Hist): Electronic key antenna circuit abnormal at driver door

-

Short in Front Passenger Side Door Oscillators Circuit

Short in front passenger door electronic key antenna circuit

OK or NG

OK: Electronic key antenna circuit normal at front passenger door

NG: Electronic key antenna circuit abnormal at front passenger door

-

Short in Driver Side Door Oscillators Circuit

Short in driver door electronic key antenna circuit

OK or NG

OK: Electronic key antenna circuit normal at driver door

NG: Electronic key antenna circuit abnormal at driver door

-

  • *: Actual vehicle data provided for reference.

HINT:

  • *1: With the engine switch in OFF, all doors closed, electronic key transmitter sub-assembly outside the vehicle and all doors locked, the unlock sensor of the front door outside handle assembly is touched.
  • *2: Approximately 150 ms
  • *3: With the engine switch in OFF, all doors closed, electronic key transmitter sub-assembly outside the vehicle and all doors unlocked, the lock sensor of the front door outside handle assembly is touched.
Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ACC SW

Engine Switch Status

ON or OFF

ON: Engine switch in ON (ACC)

OFF: Engine switch in OFF

"ON" is also displayed when the engine switch is in ON (IG).

IG SW

Engine Switch Status

ON or OFF

ON: Engine switch in ON (IG)

OFF: Engine switch in OFF

"OFF" is also displayed when the engine switch is in ON (ACC).

RR Door Courtesy SW

Rear Right Door Threshold Light Switch

ON or OFF

ON: Right rear door open.

OFF: Right rear door closed.

-

RL Door Courtesy SW

Rear Left Door Threshold Light Switch

ON or OFF

ON: Left rear door open.

OFF: Left rear door closed.

-

Back Door Courtesy SW

Luggage compartment door sill light switch

ON or OFF

ON: Back door open.

OFF: Back door closed.

-

FR Door Lock Pos

Front Right Door Unlock Detection Switch Signal

UNLOCK or LOCK

UNLOCK: Front right door unlocked.

LOCK: Front right door locked.

-

FR Door Courtesy SW

Front Right Door Threshold Light Switch Signal

ON or OFF

ON: Front RH door open

OFF: Front RH door closed

-

FL Door Lock Pos

Front Left Door Unlock Detection Switch Signal

UNLOCK or LOCK

UNLOCK: Front left door unlocked.

LOCK: Front left door locked.

-

FL Door Courtesy SW

Front Left Door Threshold Light Switch Signal

ON or OFF

ON: Front left door open

OFF: Front left door closed

-

RR-Door Lock Pos SW

Rear Left and Right Door Unlock Detection Switch Signal

ON or OFF

ON: Rear left and right doors unlocked

OFF: Rear left and right doors locked

-

RL-Door Lock Pos SW

Rear Left and Right Door Unlock Detection Switch Signal

ON or OFF

ON: Rear left and right doors unlocked

OFF: Rear left and right doors locked

-

Wireless Control

Remote Control Central Door Locking Function

ON or OFF

Customised setting displayed

-

Hazard Answer Back

Automatic Hazard Light Response to Opening Function

ON or OFF

Customised setting displayed

-

Open Door Warning

Door Open Warning

ON or OFF

Customised setting displayed

-

Auto Lock Time

Auto Lock Delay

30, 60 or 120 s

Customised setting displayed

-

Wireless Buzzer Resp

Automatic Remote Control Buzzer Response to Opening Function

ON or OFF

Customised setting displayed

with Toyota Safety Sense P system

Wireless Buzzer Vol

Remote Control Buzzer Volume

Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0

Customised setting displayed

with Toyota Safety Sense P system

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Shift P Signal

P Position Engaged

ON or OFF

ON: Shift lever in P position

OFF: Shift lever in a position other than P

  • Follow this option to determine whether the malfunction is in the shift lever position switch.
  • The engine cannot be started when this function is disabled.

Steering Unlock Switch

Steering unlock sensor status signal output by the steering lock ECU (steering lock actuator set or upper support)

ON or OFF

ON: Steering unlocked

OFF: Steering locked

  • When the shift lever is in P*1, the engine start switch is OFF, and a door is opened and then closed, the steering is locked.
  • When the key is inside the cabin and the engine start switch is in ON (ACC) or ON (IG), the steering is unlocked.
  • The engine cannot be started when the steering lock release sensor signal is OFF.

Stop Light Switch1

Brake Pedal Status

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

  • Use this item to determine whether the malfunction is in the stop light switch assembly.
  • The engine cannot be started when this function is disabled.
  • If the stop light switch assembly is faulty, the engine can be started by pressing and holding the engine start switch for a certain period of time.

Start Switch1

Engine Start Switch 1 Status

ON or OFF

ON: Engine start switch pressed

OFF: Engine start switch not pressed

  • If the engine start switch is pressed briefly, the value shown on the screen may not change.
  • Use this item to determine whether the malfunction is in the engine start switch input signal.

Start Switch2

Engine Start Switch 2 Status

ON or OFF

ON: Engine start switch pressed

OFF: Engine start switch not pressed

  • Backup power supply for start switch 1. However, when the engine start switch is held pressed, the control operates only when both start switches 1 and 2 are normal.
  • Operates in the same way as start switch 1.

Vehicle Speed Signal

Vehicle moving or stopped

Stop or Run

Stop: Vehicle stopped

Run: Vehicle speed at or above 5 km/h

-

Power Supply Condition

Power Supply Status

All OFF, ACC ON, IG ON or ST ON

All OFF: Engine start switch in OFF position

ACC ON: Engine start switch in ON (ACC) position

IG ON: Engine start switch in ON (IG) position

ST ON: Engine start request signal transmitted

-

Body Electrical > Combination Meter > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed Meter

Vehicle speed

Min.: 0 km/h, Max.: 255 km/h

Almost identical to the actual vehicle speed

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body or Smart Key / Active Test.

(e) Perform the Active Test by following the instructions shown on the Techstream screen.

Body Electrical > Smart Key > Active Test

Tester display

Item

Control Range

Diagnostic Note

Overhead Tuner Power Supply ON

Electronic Key and TPMS Receiver Assembly

OFF / ON

-

Power for P-Seat Sens

Front Door Outside Handle RH

OFF / ON

-

Multi Channel SW

Electronic Key and TPMS Receiver Assembly

CH1/CH2

-

Body Electrical > Main Body > Active Test

Tester display

Item

Control Range

Diagnostic Note

Door Lock

Door Lock Motor

OFF / Unlock / Lock

-

D-Door Unlock

Driver Door Lock Motor

OFF / ON

-

Trunk and Back-Door Open

Trunk Lock Motor

OFF / ON

-

Wireless Buzzer

Remote Door Lock Buzzer

OFF / ON

-