Theft Deterrent / Keyless Entry

Additional key registration not possible

~8min read

DESCRIPTION

If additional registration is not possible, a malfunction is suspected in the Electronic Key Transmitter Assembly, Certification ECU (Smart Key ECU Assembly), engine switch, No. 1 Interior Electronic Key Antenna Assembly (Front Floor), Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly), or Electronic Key and TPMS Receiver Assembly.

PRECAUTION / NOTICE / HINT

NOTICE:

  • If an electronic key transmitter sub-assembly cannot be registered, confirm the procedure in the immobiliser system.

    Click here

  • The Smart Key System (for Access Function) uses a LIN communication system and a CAN communication system. Check the communication function by following the procedure described in HOW TO USE TROUBLESHOOTING MODE. Troubleshoot the Smart Key System (for Access Function) after confirming that the communication systems operate normally.

    Click here

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Before replacing the Certification ECU (Smart Key ECU Assembly), Steering Lock ECU (Steering Lock Actuator or Upper Support Assembly), or Electronic Key Transmitter Assembly, refer to the precautions.
  • After repair, confirm that no DTCs are output.

HINT:

When additional registration is not possible, freeze frame data may be stored in the Certification ECU (Smart Key ECU Assembly).

If freeze frame data is available, it can help identify potential malfunctions in the parts or the areas concerned based on the table below.

Recording Function (Non-Operation Reason)

Parameter Name

Cause and Corrective Action

Registration Mode Failure

Make sure no other mode or a different registration mode is activated, then restart the registration.

Maximum Key Registration

Registration failed because the maximum number of electronic key transmitter sub-assemblies has already been registered in the certification ECU (smart key ECU assembly).

If a new electronic key transmitter sub-assembly needs to be registered, for example if one of the registered sub-assemblies is lost, first erase an unnecessary ID code.

Key Verification: Abnormal Amplifier

Although the registered electronic key transmitter sub-assembly was held near the engine switch, registration of the electronic key transmitter sub-assembly cannot be confirmed due to a malfunction in the immobiliser amplifier, such as a short to ground. DTC B278A or B2784 is stored.

Key Verification: Read Error

A registered electronic key transmitter sub-assembly was not held correctly near the engine switch, or registration of the electronic key transmitter sub-assembly could not be confirmed due to radio wave interference, etc.

Register the electronic key transmitter sub-assembly using the correct procedure, or use another registered electronic key transmitter sub-assembly.

Abnormal Transponder Key Amplifier

Although the registered electronic key transmitter sub-assembly was held near the engine switch, registration of the electronic key transmitter sub-assembly cannot be completed due to a malfunction in the immobiliser amplifier, such as a short to ground. DTC B278A or B2784 is stored.

New Key Registration Error

An unregistered electronic key transmitter sub-assembly was not held correctly near the engine switch, or registration of the electronic key transmitter sub-assembly could not be confirmed due to a malfunction, such as radio wave interference.

Register the electronic key transmitter sub-assembly again using the correct procedure, or use another registered electronic key transmitter sub-assembly.

New Vehicle Key ID Code Error

Although the vehicle identification code registered in the certification ECU (smart key ECU assembly) must be registered in the electronic key transmitter when the electronic key transmitter sub-assembly is registered, this was not done.

Use another electronic key transmitter sub-assembly for registration.

New Key Registration Failure

Although the unregistered electronic key transmitter sub-assembly was held near the engine switch, registration of the electronic key transmitter sub-assembly cannot be completed due to radio wave interference (such as radio waves emitted by a component in the cabin) or low transmitter battery voltage.

New Key Already Registered

The registered electronic key transmitter sub-assembly was held near the engine switch by mistake, and registration of the electronic key transmitter sub-assembly failed.

Using an unregistered electronic key transmitter sub-assembly, perform the registration procedure again.

New Key ID Code Error

Replace the certification ECU (smart key ECU assembly).

Abnormal New Key Information

The ID code of the electronic key transmitter sub-assembly could not be registered in the certification ECU (smart key ECU assembly). If 2 electronic key transmitter sub-assemblies were held near the engine switch at the same time, incorrect registration information was stored in the certification ECU (smart key ECU assembly), and registration was suspended.

Register the electronic key transmitter sub-assemblies again using the correct procedure.

Body Electrical > Smart Key > Utility

Operation History

PROCEDURE

  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Check the DTCs.

Body Electrical > Smart Key > Trouble Codes

OK:

No DTCs are output.

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

OK
  1. READ THE VALUE USING TECHSTREAM (UNMATCHED VEHICLE ID)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Smart Key / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Unmatched Vehicle-ID

Key No. (Correct or Incorrect)

Yes or No

Yes: Communication malfunction

No: Communication normal

The Vehicle-ID registered in the vehicle and the Vehicle-ID registered in the key are different (if a key for another vehicle is brought into the vehicle's exterior detection area while the doors are locked, "YES" is displayed for the "Unmatched Vehicle-ID" Data List item).

Other possible causes:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • A communication error due to radio wave interference.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.
Body Electrical > Smart Key > Data List

Unmatched Vehicle-ID

Result:

Result

Proceed to

"No" is displayed

A

"Yes" is displayed

B

B

GO TO STEP 4

A
  1. CHECK THE STEERING LOCK SYSTEM

(a) Check whether the steering unlocks.

Click here

HINT:

Make sure communication between the steering lock ECU (steering lock actuator or upper support assembly) and the certification ECU (smart key ECU assembly) is normal.

OK:

The steering unlocks.

NG

GO TO THE STEERING LOCK SYSTEM

OK
  1. REGISTRATION

(a) Using an unregistered electronic key transmitter sub-assembly, perform the new registration procedure again.

HINT:

Refer to Registration.

Click here

OK:

Additional registration failed.

OK

REPLACE THE ELECTRONIC KEY TRANSMITTER SUB-ASSEMBLY (THE FIRST REGISTERED KEY WAS DEFECTIVE)

NG
  1. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

(a) Replace the Certification ECU (Smart Key ECU Assembly) with a new one and register the Electronic Key Transmitter Assemblies.

Click here

HINT:

Refer to Registration.

Click here

OK:

All Electronic Key Transmitter Assemblies were registered to the new Certification ECU (Smart Key ECU Assembly).

OK

END (CERTIFICATION ECU (SMART KEY SYSTEM ECU ASSEMBLY) WAS FAULTY)

NG

REFER TO THE OTHER PROBLEM (New Key Cannot Be Registered)