Theft Deterrent / Keyless Entry

Back door lock function does not operate

~5min read

DESCRIPTION

If the back door lock function does not operate, but the unlock function operates, the request code is transmitted correctly by the back door. In this case, there may be a malfunction in the lock switch (connection between the back door opener switch assembly and the certification ECU (smart key ECU assembly)).

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • The Smart Key System (for Access Function) uses a LIN communication system and a CAN communication system. Check the communication function by following the procedure described in HOW TO USE TROUBLESHOOTING MODE. Troubleshoot the Smart Key System (for Access Function) after confirming that the communication systems operate normally.

    Click here

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Check that no Electronic Key Transmitter Sub-assembly is inside the vehicle.
  • Before replacing the Certification ECU (Smart Key ECU Assembly), refer to the precautions.

    Click here

  • After repair, confirm that no DTCs are output.

PROCEDURE

  1. INSPECT DOOR LOCK CONTROL SYSTEM

(a) When the door control switch on the Multiplex Network Main Switch Assembly is operated, check whether the doors lock and unlock according to the switch operation.

Click here

OK:

The door locks operate normally.

NG

GO TO DOOR LOCK CONTROL SYSTEM

OK
  1. CHECK TECHSTREAM (TR/B-DOOR LOCK SW)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Smart Key / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Tr/B-Door Lock SW

Trunk door opener switch assembly (lock switch)

ON or OFF

ON: Back door opener switch assembly (lock switch) pressed

OFF: Back door opener switch assembly (lock switch) not pressed

  • Displayed whether the back door opener switch assembly (lock switch) is ON or OFF.
  • Use this Data List item to determine whether there is a malfunction in the switch when the back door lock function does not operate.
Body Electrical > Smart Key > Data List

Tr/B-Door Lock SW

HINT:

When repeatedly checking the operation of the lock function upon door opening, it can be operated up to 2 times in succession. To activate the function at least 3 times in succession, the doors must be unlocked once. However, this applies only to the lock function upon door opening; other door lock operations, such as remote door lock operation, can be performed in succession.

OK:

The Techstream display changes correctly in response to operation of the luggage compartment door opening switch assembly.

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG
  1. INSPECT THE WIRE HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect connector M67 from the certification ECU (smart key ECU assembly).

(b) Disconnect connector S8 from the luggage compartment door opening switch assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M67-27 (TSW6) - S8-1 (L)

Always

Below 1 Ω

S8-2 (E) - Body ground

Always

Below 1 Ω

M67-27 (TSW6) or S8-1 (L) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK BACK DOOR OPENER SWITCH ASSEMBLY (LOCK SWITCH)

(a) Remove the luggage compartment door opening switch assembly.

Click here

(b) Inspect the luggage compartment door opening switch assembly.

Click here

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG

REPLACE THE LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY