Theft Deterrent / Keyless Entry

System Description

~52min read

SYSTEM DESCRIPTION

MULTIPLEX FUNCTION

(a) The electronic key transmitter sub-assembly and the electronic key or TPMS receiver assembly can operate together on two different RF channels. When the electronic key transmitter sub-assembly is placed in the outside detection area, key verification starts. If key verification fails due to wave interference, the channel is switched and key verification is performed again.

The multiplex system starts verification using the channel on which the last verification was successfully performed. If verification fails, the system switches to the other channel.

*a

The outside detection areas are created using LF waves (transmitted by the vehicle at 0.25-second intervals) to receive a response from the electronic key transmitter sub-assembly.

*b

When the electronic key transmitter sub-assembly is placed in an outside detection area, it receives LF waves from the vehicle. Using RF waves, the electronic key transmitter sub-assembly responds to the vehicle.

*c

Upon receiving the response from the electronic key transmitter sub-assembly, the certification ECU (smart key system ECU assembly) activates the electronic key antennas (outside) one after another. Using LF waves, the certification ECU (smart key system ECU assembly) determines the outside detection area in which the electronic key transmitter sub-assembly is located.

*d

The electronic key transmitter sub-assembly receives LF waves sent by the vehicle and responds using RF waves. (The certification ECU (smart key system ECU assembly) recognizes in which outside detection area the electronic key transmitter sub-assembly is located.)

*e

The certification ECU (smart key system ECU assembly) sends registered key ID information to the electronic key transmitter sub-assembly using LF waves. (Up to 7 keys can be registered.)

*f

The electronic key transmitter sub-assembly transmits key ID information using RF waves. When the certification ECU (smart key system ECU assembly) receives it, verification is complete.

*g

Wave Interference (Channel Switching)

-

-

The multiplex system switches channels when the RF band (*b, *d and *f) is interrupted by wave interference. Refer to the table below to check when the system switches channels.

*b or *d is NG

*f is NG

Condition

Unable to receive RF waves

Unable to receive RF waves correctly

Unable to receive RF waves

Unable to receive RF waves correctly

Channel Switching

Channels will not be switched.

Channels will be switched.

Channels will not be switched.

Channels will be switched*.

  • *: Channels are not changed when verifying inside the vehicle after the lock-on-open function is activated.

SMART KEY SYSTEM SPECIFICATIONS

(a) Some customers may ask about the frequency used by the smart key system of different models. This repair manual contains the specifications applicable to the smart key system.

*a

Transmitter Detection Area

-

-

LF Smart Key System Antenna Power Specifications

Specifications

Frequency

Power/Electric Field Strength

Modulation Method

Mounting Location in Vehicle

Inside the Passenger Compartment

134.2 kHz

94.4 dBuV/m at 3 m

AM

Inside the Vehicle

Outside the Vehicle

134.2 kHz

95 dBuV/m at 3 m

AM

Inside the Door Handle

95 dBuV/m at 3 m

AM

Inside the Rear Bumper

LF Smart Key System Transmission Timing Specifications

Transmission Timing

Vehicle Remains Parked

When Entering or Exiting the Vehicle

Vehicle Is Running

Inside the Passenger Compartment

Does Not Transmit

  • Door Lock Operation
  • Engine Switch / Brake Pedal Operation
  • Opening or Closing Doors
  • With the engine switch in ON (IG) or ON (ACC) position and the shift lever in P, closing any door when the electronic key transmitter assembly cannot be detected inside the vehicle (continues for 3 seconds until the electronic key transmitter assembly is detected or the engine switch is turned OFF)
  • Engine switch is turned OFF after driving for more than 20 minutes
  • With the shift lever in a position other than P, closing any door when the electronic key transmitter assembly cannot be detected inside the vehicle (continues for 3 seconds until the electronic key transmitter assembly is detected)

When the electronic key transmitter assembly is not detected in the passenger compartment while the vehicle is moving (transmits for 4 seconds)

Outside the Vehicle

(1) When the door is locked, transmits at 250 ms intervals (stops when the door is unlocked)

(2) Does not transmit

(1) Touch the lock sensor

(2) Press the trunk door opening switch assembly

(3) Touch the unlock sensor in power saving mode

Does Not Transmit

BASIC PRECAUTIONS

(a) DTCs and ECU Data List related to the smart key system cannot be checked using the Techstream.

(b) Check for any DTCs using the following procedure. If DTCs are output, perform diagnosis for those DTCs first.

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch to ON (IG).

(3) Select the following menu items: Body Electrical / Smart Key, Power Source Control or Starting Control / Trouble Codes.

(c) While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type manually and enter the following menu items: Body Electrical / Smart Key. While using the Techstream, repeatedly turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.

(d) If the smart key system has been disabled by a customized setting, enable the smart key system.

Click here

SMART KEY SYSTEM DIAGRAM

SYSTEM DESCRIPTION

The following diagram is used: "Operation" indicates that the user has performed an operation using the smart key system. "Expected Vehicle Operation" indicates how a vehicle in good condition will respond to each operation. "Suspected Area/Diagnosis" indicates a malfunction in the suspected components and tips for performing diagnosis if the vehicle does not respond as expected.

(a) Example: Operation Number

Operation

-

Expected Vehicle Operation

-

Waveform or Output Value

-

Suspected Area

Diagnosis

-

-

DIAGNOSIS BASED ON USER OPERATION

(a) Operation 1

Operation

Turn the engine switch OFF and lock all doors, then place the electronic key transmitter assembly at least approximately 3 m (9.84 ft) away from the vehicle.

HINT:

The detection area of each electronic key antenna (outside) is defined by sending a periodic LF band request signal every 0.25 seconds. The detection area formed by each front outside door handle assembly (electronic key antenna) has a detection range of approximately 0.7 m (2.30 ft).

Waveform or Output Value

Pulse Generation (M66-17 (CLG1) - F1-18 (E)*1)

  • *1: Click here

(b) Operation 2

Operation

Bring the electronic key transmitter assembly within 0.7 m (2.30 ft) of the driver side door.

HINT:

The system will enter unlock standby mode when the electronic key transmitter assembly is brought into the detection area and the key ID code sent by the electronic key transmitter assembly matches the key ID code registered by the certification ECU (smart key ECU assembly). The door unlocks when the unlock sensor is touched with the hand while the system is in unlock standby mode.

Signal transmission: Certification ECU (smart key ECU assembly) → Front outside door handle assembly (electronic key antenna) → Electronic key transmitter assembly → Electronic key and TPMS receiver assembly → Certification ECU (smart key ECU assembly) → Main body ECU (multiplex network body ECU)

Expected Vehicle Operation

The LED on the electronic key transmitter assembly starts flashing. If it does not, check the suspected components in the following table.

Waveform or Output Value

  • Pulse Generation (M66-17 (CLG1) - F1-18 (E)*1)
  • Pulse Generation (M66-18 (RCO) - F1-18 (E)*1)
  • Pulse Generation (M66-19 (RDAM) - F1-18 (E)*1)
  • Pulse Generation (M66-20 (CSEL) - F1-18 (E)*1)
  • *1: Click here

Suspected Area

Diagnosis

Electronic Key Transmitter Sub-assembly

  • The key ID code transmitted by the electronic key transmitter subassembly does not match the key ID code registered in the certification ECU (smart key ECU assembly). Use a different electronic key transmitter subassembly to check operation.
  • If the electronic key transmitter subassembly LED does not flash when the transmitter is placed 0.7 m (2.30 ft) from the front door outside handle assembly LH, perform the following procedure.

    Press the lock and unlock switches on the electronic key transmitter subassembly to check operation. If the doors cannot be locked and unlocked, the detection area has not been formed. Parts other than the electronic key transmitter subassembly and the electronic key and TPMS receiver assembly may be malfunctioning.

  • If the electronic key transmitter subassembly malfunctions, the engine cannot be started and the engine switch cannot be set to ON (ACC) or ON (IG). Under normal operating conditions, the multi-information display in the combination meter assembly shows the door open indicator when the engine switch is pressed while the electronic key transmitter subassembly is in the driver seat area, the shift lever is in P, and the brake pedal is released. If the driver door cannot be opened, use the mechanical key stored in the electronic key transmitter subassembly to open the door.

HINT:

  • Before replacing the electronic key transmitter subassembly, check whether the transmitter battery is depleted.
  • If the driver door cannot be opened, use the mechanical key stored in the electronic key transmitter subassembly to open the door.

The transmitter battery is depleted

  • Press and hold the lock switch on the electronic key transmitter subassembly for 5 seconds, then check how many times the electronic key transmitter subassembly LED flashes. If the LED does not flash or flashes only once or twice, the transmitter battery may be depleted. If the LED does not flash at all, the electronic key transmitter subassembly may be malfunctioning.
  • If the transmitter battery voltage drops to 2.2 V or less when the electronic key transmitter subassembly sends a signal, "Yes" is displayed for "Key Low Battery" in the Data List.
  • If the transmitter battery voltage drops to 2.0 V or less, operation cannot be guaranteed.

    HINT:

    The output voltage of the electronic key transmitter subassembly decreases in low temperatures.

  • When the transmitter battery is depleted, the engine cannot be started and the engine switch cannot be set to ON (ACC) or ON (IG). If the electronic key transmitter subassembly is held close to the engine switch, the engine can be started.
  • Make sure the transmitter battery type and installation direction are correct.

Radio wave interference

  • If the problem occurs in certain locations or at certain times of day, the risk of radio wave interference may be high.
  • When the electronic key transmitter subassembly does not operate correctly, the transmitter battery is depleted, a electronic key transmitter subassembly from another vehicle has been used, or radio wave interference is suspected. "Yes" may be displayed for one of the following items in the Data List: "Unmatch Code or Form", "No Response", "ID Code Difference" or "Unmatched Vehicle-ID".

Certification ECU (Smart Key ECU Assy)

-

Main body ECU (multiplex network body ECU)

-

Front Door Outside Handle Assembly

The vehicle exterior detection area is not formed correctly.

  • If the electronic key transmitter subassembly LED does not flash when placed 0.7 m (2.30 ft) from the front door outside handle assembly LH, but flashes when placed 0.7 m (2.30 ft) from the front door outside handle assembly RH, the front door outside handle assembly on the driver door may be malfunctioning.
  • Even if the vehicle exterior detection area is not formed correctly, the engine switch can be set to ON (ACC) and the engine can be started.
  • The formation of the vehicle exterior detection area can be checked using the Techstream.

    Click here

  • Even if the vehicle exterior detection area is not formed correctly, the doors can be unlocked by pressing the unlock switch on the electronic key transmitter subassembly.

Electronic Key and TPMS Receiver Assembly

  • If the electronic key and TPMS receiver assembly malfunctions, the front passenger door and rear doors cannot be unlocked.
  • If the electronic key and TPMS receiver assembly malfunctions, the doors cannot be unlocked by the remote unlock operation.
  • If the electronic key and TPMS receiver assembly malfunctions, the engine cannot be started and the engine switch cannot be set to ON (ACC or IG), except in an emergency.
  • The formation of the vehicle exterior detection area can be checked using the Techstream.

    Click here

Battery depleted

You may be able to tell whether the battery is depleted by operating the horn.

Other

  • If the smart key system function has been disabled using the customization function, the detection area cannot be formed. Therefore, the electronic key transmitter subassembly LED does not flash even when the transmitter is placed near the front door outside handle assembly.
  • In the smart key system, if the electronic key transmitter is kept constantly within the outside detection area of one of the doors, the transmitter battery may discharge. Therefore, if this situation continues for more than 10 minutes, the smart key system automatically deactivates the outside detection area in which the electronic key transmitter is located.
  • If the electronic key transmitter is in transmitter battery saving mode, it does not respond with RF waves even if it receives LF waves from the vehicle. Therefore, the electronic key transmitter LED does not blink.
  • If the electronic key transmitter is left inside the vehicle and the doors are locked using another electronic key transmitter, the electronic key transmitter LED does not blink even when it is brought near the front door outside handle assembly.

(c) Operation 3

Operation

With the electronic key transmitter in the outside detection area, touch the unlock sensor of the front door outside handle assembly LH.

Expected Vehicle Operation

When the doors are unlocked, an automatic response is performed at the same time. If not, check the suspect parts in the following table.

Waveform or Output Value

  • Pulse Generation (M66-17 (CLG1) - F1-18 (E)*1)
  • Connection of tester (instrument panel junction block (ACT-) - body ground)*1
  • *1: Click here

Suspected Area

Diagnosis

The suspect parts below may overlap with the parts in Operation 2 when the electronic key transmitter LED does not blink.

-

Front door outside handle assembly (unlock sensor)

  • If the doors can be unlocked by touching the unlock sensor of the front door outside handle assembly RH while carrying the electronic key transmitter, the unlock sensor of the front door outside handle assembly LH may be malfunctioning.
  • Under normal operating conditions, "ON" is displayed for the "D-Door Touch Sensor" item in the Data List when the unlock sensor is touched.

Door lock/unlock mechanism

If a door cannot be locked/unlocked by operating the door control switch on the interior door, the door lock mechanism is malfunctioning.

(d) Operation 4

Operation

After entering the vehicle with the electronic key transmitter, close the door, and press the engine switch once while shifting the shift lever to P and depressing the brake pedal.

Expected Vehicle Operation

  • The security indicator turns off, then the immobiliser function is deactivated, allowing the vehicle to operate.
  • The steering is unlocked.

If any of the above actions do not occur, check the suspect parts in the following table.

HINT:

When the engine switch is pressed, the interior electronic key antennas form a key detection area inside the vehicle and detect the electronic key transmitter in the cabin. The electronic key transmitter transmits a key ID code upon receiving a request signal, and the electronic key transmitter LED lights up briefly. After pressing the engine switch, if the key ID code transmitted by the electronic key transmitter matches the key ID code registered in the certification ECU (smart key ECU assembly), the ACC relay is activated and the open indicator is displayed on the multi-display of the combination meter assembly. Once the power mode has been changed and the L code and S code verification is complete, the steering is unlocked and the immobiliser is deactivated. The Data List item "Immobiliser" changes from "Set" to "Unset".

Signal transmission: Certification ECU (smart key ECU assembly) → Interior electronic key antenna → Electronic key transmitter → Electronic key and TPMS receiver assembly → Certification ECU (smart key ECU assembly)

HINT:

The interior detection area is formed when one of the following conditions is met:

  • A door is opened.
  • One of the doors has been opened and closed (within approximately 60 seconds).
  • The brake pedal has been depressed (within approximately 30 seconds).
  • The engine switch is pushed.

Waveform or Output Value

  • Pulse Generation (M66-19 (RDAM) - F1-18 (E)*1)
  • Pulse generation (F1-8 (CLG5) - F1-18 (E)*1)
  • Pulse generation (F1-17 (IG1D) - F1-18 (E)*1)
  • *1: Click here

Suspected Area

Diagnosis

Certification ECU (Smart Key ECU Assy)

-

Radio wave interference

  • If a malfunction occurs at a specific location or time, radio wave interference may be the cause.
  • If radio wave interference is suspected inside the cabin, disconnect the connectors of all electronic devices that are not standard equipment, or remove the electronic devices and check that they do not emit electrical noise.

Interior electronic key antenna assemblies that form the interior detection areas.

  • If the interior detection area is not formed correctly, the engine cannot be started and the engine switch cannot be set to ON (ACC) or ON (IG). In an emergency, hold the electronic key transmitter near the engine switch to start the engine.
  • Using the Techstream, switch to key diagnostic mode to forcibly form the interior detection area. If the electronic key transmitter is brought near the area, short beeps will sound.

    Click here

Engine Switch

Under normal operating conditions, once the engine switch is pressed, "ON" is displayed for the Data List items "Start Switch1" and "Start Switch2".

ID Code Box (Immobilizer ECU)

To unlock the steering, the "S Code Check" item in the Data List must display "OK". If the "S Code Check" item displays "OK", the certification ECU code (smart key system ECU assembly) and the ID code box code (immobiliser ECU) match.

Park/Neutral Position Switch

Under normal operating conditions, "ON" is displayed for the Data List item "Neutral SW/ Clutch SW" when the shift lever is in the P position.

Steering lock ECU (steering lock actuator or upper bracket assembly)

  • If "OK" is displayed for the Data List item "L Code Check" when the engine switch is set to the ON (ACC) position, power is supplied to the steering lock motor for approximately 10 seconds. The ECU then sends an unlock signal to the steering lock motor, and the Data List item "Unlock Request Receive" temporarily changes from "NG" to "OK". Once the steering is unlocked, the ECU receives the unlock signal from the steering lock motor, and the Data List item "Steering Unlock" changes from "Unset" to "Set".
  • To unlock the steering, "OK" must be displayed for the Data List item "L Code Check" (the ID code registered in the steering lock ECU (steering lock actuator or upper support assembly) matches that of the ID code box (immobiliser ECU)).

(e) Operation 5

Operation

Depress the brake pedal with the shift lever in the P position while holding the electronic key transmitter sub-assembly.

Expected Vehicle Operation

The open indicator appears on the multi-information display. If it does not, check the suspect parts in the following table.

Suspected Area

Diagnosis

Stop light switch assembly

If the brake pedal is depressed, "ON" is displayed for the Data List item "Stop Light Switch1".

Certification ECU (Smart Key ECU Assy)

Start Function - ECU Terminals

Click here

(f) Operation 6

Operation

After getting into the vehicle while carrying the electronic key transmitter sub-assembly, press the engine switch while setting the shift lever to the P position and depressing the brake pedal.

Expected Vehicle Operation

The engine starts. If it does not, check the suspect parts in the following table.

Suspected Area

Diagnosis

Steering lock system

Under normal operating conditions, the steering is unlocked and "ON" is displayed for the Data List item "Steering Unlock Switch".

Battery depleted

Operating the horn makes it easy to check whether the battery is discharged or not.

(g) Operation 7

Operation

While the engine is running, press the engine switch.

Expected Vehicle Operation

The engine stops, the open warning light comes on and then goes off, and the security indicator changes from OFF to flashing.

(h) Operation 8

Operation

Set the engine switch to the OFF position and open one of the doors.

Expected Vehicle Operation

The steering locks. If it does not, check the suspect parts in the following table.

Suspected Area

Diagnosis

Steering lock system

-

Door Courtesy Light Switch Assembly

If the driver door is open, "ON" is displayed for the Data List item "FL Door Courtesy SW".

(i) Operation 9

Operation

Touch the lock sensor on the front door outside handle assembly LH while carrying the electronic key transmitter sub-assembly.

Expected Vehicle Operation

The door lock and the automatic response are performed at the same time.

BATTERY SAVER FUNCTION

(a) When the smart key system is activated, the vehicle performs key detection operations every 0.25 seconds. Therefore, if the vehicle is left as is for a long period, the battery may become completely discharged. The following measures help reduce the battery discharge rate.

(1) If the smart key system has not been used for 5 days or more, the periodic signal transmission from the electronic key antennas stops. However, the doors can still be unlocked by touching the unlock sensor on a front door outside handle assembly.

(2) If the smart key system is not operated for 14 days or more, the lock and unlock sensors on the front door outside handle assembly RH are deactivated. Therefore, only the unlock sensor on the front door outside handle assembly LH can be used to unlock the doors.

(3) If 10 minutes or more have elapsed while the electronic key transmitter sub-assembly is in an exterior detection area, the front door outside handle assembly (electronic key antenna) that detects the electronic key transmitter sub-assembly stops operating.

(b) To restore operation of the smart key system, perform one of the following operations.

(1) While carrying the electronic key transmitter sub-assembly, touch the lock or unlock sensor on the front door outside handle assembly LH, and perform a door lock or unlock operation.

(2) Lock or unlock the doors using the remote function.

(3) Insert the mechanical key into the driver door lock cylinder and lock or unlock the doors.

REMOTE OPERATION BUZZER VOLUME ADJUSTMENT FUNCTION (with Toyota Safety Sense P)

(a) The volume of the remote control buzzer can be changed using the customize function.

HINT:

The volume of the following remote control buzzer operations cannot be adjusted.

  • Warning function buzzer operations
  • Customize function buzzer operations
  • Key diagnosis mode buzzer operations using the Techstream
  • Key registration buzzer operations

WARNING FUNCTION

(a) Alarm

(1) Situation: The engine is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.

  • There are 2 cases for this situation.
    • Sequence 1:

      When the engine is running and the shift lever is in a position other than P, the driver opens the door and attempts to exit the vehicle.

      In this type of situation, the following operation is performed:

      Warning purpose

      Prevention of sudden acceleration, vehicle anti-theft system, prevention of unintended vehicle movement

      Warning start condition

      (all conditions are met)

      • The engine switch is in ON (ACC) or ON (IG) position.
      • The shift lever is in a position other than P.
      • The driver's door is open.
      • No vehicle speed is detected.

      Warning description

      • The buzzer in the instrument cluster sounds continuously.
      • "Shift to P Before Exiting Vehicle" is displayed on the multi-information display of the instrument cluster.

      Warning stop condition

      (one condition is met)

      • The engine switch is in OFF position.
      • The shift lever is in P position.
      • The driver's door is closed.
      • The vehicle speed is at least 5 km/h.
    • Sequence 2:

      In the situation of Sequence 1, the driver closes the door and attempts to exit the vehicle while carrying the electronic key transmitter.

      In this type of situation, the following operation is performed:

      Warning purpose

      Prevention of sudden acceleration, vehicle anti-theft system, prevention of unintended vehicle movement

      Warning start condition

      (all conditions are met)

      • The engine switch is in ON (ACC) or ON (IG) position.
      • The shift lever is in a position other than P.
      • Driver's door open → closed.
      • The electronic key transmitter is not inside the vehicle.
      • No vehicle speed is detected.

      Warning description

      • The buzzer in the instrument cluster sounds continuously.
      • The remote control buzzer sounds continuously.
      • "Shift to P Before Exiting Vehicle" (A) and "Key Not Detected Check Key Location" (B) are displayed alternately on the multi-information display of the instrument cluster.

      Warning stop condition

      (one condition is met)

      Warning stop conditions for (A)

      • The shift lever is in P position.
      • The vehicle speed is 5 km/h.

      Warning stop conditions for (B)

      • The engine switch is in OFF position.
      • The electronic key transmitter is returned to the vehicle.

(2) Situation: The key reminder warning buzzer sounds.

  • There are 3 cases for this situation.
    • Sequence 1:

      When the shift lever is in position P and the steering is unlocked, the driver opens the door and attempts to exit the vehicle.

      In this type of situation, the following operation is performed:

      Warning purpose

      Vehicle anti-theft system

      Warning start condition

      (the warning starts when condition 1 is met or condition 2 is met for 1 second)

      Condition 1

      • The engine switch is in the ON (ACC) position.
      • The driver's door is open.

      Condition 2

      • The engine switch is in OFF position.
      • The steering is unlocked.
      • The driver's door is open.

      Warning description

      • The buzzer in the instrument cluster sounds continuously at short, regular intervals.

      Warning stop condition

      (one condition is met)

      • The engine switch is set to ON (IG).
      • The driver's door is closed.
      • The engine switch is set to OFF and the steering is locked.
    • Sequence 2:

      In the situation of Sequence 1, the driver closes the door and attempts to exit the vehicle while carrying the electronic key transmitter.

      In this type of situation, the following operation is performed:

      Warning purpose

      Vehicle anti-theft system

      Warning start condition

      (all conditions are met)

      • The engine switch is in ON (ACC) or ON (IG) position.
      • The shift lever is in P position.
      • Driver's door open → closed.
      • The electronic key transmitter is not inside the vehicle.
      • No vehicle speed is detected.

      Warning description

      • The buzzer in the instrument cluster sounds once.
      • The remote control buzzer sounds 3 times.
      • "Key Not Detected Check Key Location" is displayed on the multi-information display of the instrument cluster.

      Warning stop condition

      (one of the following conditions is met)

      • The engine switch is in OFF position.
      • The electronic key transmitter is returned to the vehicle.
    • Sequence 3:

      In the situation of Sequence 2, the driver touches the lock sensor on the outside door handle assembly.

      In this type of situation, the following operation is performed:

      Warning purpose

      Vehicle anti-theft system

      Warning start condition

      (all conditions are met)

      • The engine switch is in ON (ACC) or ON (IG) position.
      • The shift lever is in P position.
      • The electronic key transmitter is not within the interior detection areas.
      • The electronic key transmitter is within the exterior detection areas.
      • Lock sensor ON.
      • No vehicle speed is detected.

      Warning description

      • The buzzer in the instrument cluster sounds once.
      • The remote control buzzer sounds continuously.
      • "Turn Power Off" (A) and "Key Not Detected Check Key Location" (B) are displayed alternately on the multi-information display of the instrument cluster.

      Warning stop condition

      (one condition is met)

      • 5 seconds have elapsed since the warning started (only the remote control buzzer stops sounding).
      • A door is open (only the remote control buzzer stops sounding).
      • A door is closed (only the remote control buzzer stops sounding).

      Warning stop conditions for (A)

      • 60 seconds have elapsed since the warning started.
      • The engine switch is in OFF position.
      • The shift lever is in a position other than P.
      • The vehicle speed is 5 km/h.

      Warning stop conditions for (B)

      • The engine switch is in OFF position.
      • The electronic key transmitter is returned to the vehicle.

(3) Situation: A passenger exits the vehicle while carrying the electronic key transmitter.

  • When the engine switch is in the ON (ACC) or ON (IG) position, a passenger opens a door other than the driver's door and attempts to exit the vehicle while carrying the electronic key transmitter.

    In this type of situation, the following operation is performed:

    Warning purpose

    Prevent the vehicle from being unable to restart

    Warning start condition

    (all conditions are met)

    • The engine switch is in ON (ACC) or ON (IG) position.
    • A door other than the driver's door is opened → closed.
    • The electronic key transmitter is not inside the vehicle.
    • No vehicle speed is detected.

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • The remote control buzzer sounds 3 times.
    • "Key Not Detected Check Key Location" is displayed on the multi-information display of the instrument cluster.

    Warning stop condition

    (one of the following conditions is met)

    • The engine switch is in OFF position.
    • The electronic key transmitter is returned to the vehicle.

(4) Situation: The electronic key transmitter is not within the interior or exterior detection areas.

  • The driver attempts to set the engine switch to ON (IG) when the electronic key transmitter is not in the cabin, or attempts to change the power supply mode by touching the electronic key transmitter to the engine switch.

    In this type of situation, the following operation is performed:

    Warning purpose

    Avoid confusion for the user

    Warning start condition

    (all conditions are met)

    • The engine immobilizer system is activated.
    • The electronic key transmitter is not inside the vehicle or the transmitter battery is discharged. (the interior check fails, or the check fails when the transmitter battery is discharged and the electronic key transmitter has been touched to the engine switch).
    • There is no history of unlocking the doors with the mechanical key and no history of check errors when the engine switch is pressed.

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Key Not Detected Check Key Location" is displayed on the multi-information display of the instrument cluster.

    Warning stop condition

    (one condition is met)

    • 15 seconds have elapsed since the warning started.
    • The electronic key transmitter is returned to the vehicle. (the interior check passes, or the check passes when the transmitter battery is discharged and the electronic key transmitter has been touched to the engine switch).
    • The driver's door is opened using the outside door handle and 30 seconds have elapsed.

(5) Situation: The vehicle is driven without a registered electronic key transmitter.

  • In this type of situation, the following operation is performed:

    Warning purpose

    Prevent the vehicle from being unable to restart

    Warning start condition

    (all conditions are met)

    • The engine switch is in the ON (IG) position.
    • The warning operates when the passenger exits the vehicle while carrying the electronic key transmitter.
    • The vehicle speed is at least 5 km/h.
    • The electronic key transmitter is not inside the vehicle.

    Warning description

    • The buzzer in the instrument cluster sounds nine times.
    • "Key Not Detected Check Key Location" is displayed on the multi-information display of the instrument cluster.

    Warning stop condition

    (one of the following conditions is met)

    • The electronic key transmitter is returned to the vehicle.
    • The engine switch is in OFF position.

(6) Situation: The electronic key transmitter subassembly is left in the vehicle.

The lock sensor on an outside door handle assembly is touched to perform lock-on-exit with the electronic key transmitter subassembly left in the vehicle.

In this type of situation, the following operation is performed:

Warning purpose

Vehicle anti-theft system

Warning start condition

(all conditions are met)

  • The engine switch is in OFF position.
  • All doors are closed.
  • The electronic key transmitter subassembly is inside the vehicle.
  • The lock sensor on an outside door handle assembly is ON (touched).
  • One of the doors is unlocked.
  • No vehicle speed is detected.

Warning description

  • The remote control buzzer sounds continuously.
  • "Key Detected in Vehicle" is displayed on the multi-information display of the instrument cluster assembly.

Warning stop condition

(one condition is met)

  • 5 seconds have elapsed since the remote control buzzer sounded (only the remote control buzzer stops sounding).
  • The engine switch is in ON (ACC) or ON (IG) position.
  • The vehicle speed is at least 5 km/h.
  • A door is open (only the remote control buzzer stops sounding).
  • The doors are locked.
  • 60 seconds have elapsed since the warning started.

(7) Situation: A door is ajar.

  • The lock sensor on an outside door handle assembly is touched to perform lock-on-exit with a door open.

    In this type of situation, the following operation is performed:

    Warning purpose

    Vehicle anti-theft system

    Warning start condition

    (all conditions are met)

    • The engine switch is in OFF position.
    • A door other than the door locked using the lock-on-exit function is not fully closed.
    • The lock sensor is ON or the lock switch is pressed on the electronic key transmitter subassembly.
    • The electronic key transmitter is within the exterior detection areas.

    Warning description

    • The remote control buzzer sounds continuously.

    Warning stop condition

    (one condition is met)

    • 5 seconds have elapsed since the remote control buzzer sounded.
    • The engine switch is in ON (ACC) or ON (IG) position.
    • All doors are closed.
    • The doors are unlocked by the remote door unlock operation.
    • The doors are unlocked using the unlock-on-exit function.
    • One of the doors is open.

(8) Situation: The electronic key transmitter subassembly is locked in the vehicle.

  • The electronic key transmitter subassembly is locked in the vehicle.

    In this type of situation, the following operation is performed:

    Warning purpose

    Vehicle anti-theft system

    Warning start condition

    Condition 1 (all of the following conditions are met)

    • With a door open, the lock button is pressed and then the door is closed while pulling the door handle.
    • The electronic key transmitter subassembly is inside the vehicle.
    • No vehicle speed is detected.

    Condition 2 (all of the following conditions are met)

    • The engine switch is in OFF position.
    • All doors are closed and locked.
    • A locking operation other than a lock-on-exit operation is performed.
    • The electronic key transmitter subassembly is inside the vehicle (the corresponding code is detected inside the vehicle).

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • The remote control buzzer sounds continuously.
    • "Key Detected in Vehicle" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one condition is met)

    • 5 seconds have elapsed since the remote control buzzer sounded (only the remote control buzzer stops sounding).
    • 60 seconds have elapsed since the warning started.
    • The power supply mode changes to a mode other than OFF.
    • A door is open (only the remote control buzzer stops sounding).
    • The doors are locked.
    • The vehicle speed is at least 5 km/h.

(9) Situation: The transmitter battery is low.

  • The vehicle is driven using an electronic key transmitter subassembly whose transmitter battery is low.

    In this type of situation, the following operation is performed:

    Warning purpose

    Prevents the vehicle from being unable to restart (convenience function)

    Warning start condition

    (one of conditions 1 or 2 is met)

    Condition 1 (all of the following conditions are met)

    • The engine switch is set to OFF after being left in the ON (IG) position for more than 20 minutes.
    • The transmitter battery voltage is low.
    • The electronic key transmitter subassembly is inside the vehicle.
    • No vehicle speed is detected.

    Condition 2 (all of the following conditions are met)

    • Engine is in OFF mode → engine is started
    • The transmitter battery voltage is low.
    • The electronic key transmitter subassembly is inside the vehicle.
    • No vehicle speed is detected.
    • Condition 1 is met. (in the past)

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Key Battery Low Replace Key Battery" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one of the following conditions is met)

    • 15 seconds have elapsed since the warning started.
    • The vehicle speed is at least 5 km/h.

(10) Situation: The steering wheel cannot be unlocked.

  • The steering wheel cannot be unlocked, so the engine cannot be started.

    The shift lever is placed in a position other than P before the steering wheel is unlocked.

    In this type of situation, the following operation is performed:

    Warning purpose

    Convenience function

    Warning start condition

    • The steering wheel cannot be unlocked (estimated by the steering lock ECU (steering lock actuator or upper support assembly)).

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Push ENGINE Switch while Turning The Steering Wheel in Either Direction" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one of the following conditions is met)

    • 15 seconds have elapsed since the warning started.
    • The steering is unlocked.

(11) Situation: The smart key system malfunctions.

  • A malfunction is detected that interferes with the steering lock ECU (steering lock actuator or upper support assembly), or a vehicle speed signal malfunction is detected.

    In this type of situation, the following operation is performed:

    Warning purpose

    Malfunction detection

    Warning start condition

    (one condition is met)

    • The steering lock ECU (steering lock actuator or upper support assembly), the certification ECU (smart key ECU assembly), or the unlock detection switch does not operate correctly.
    • The vehicle speed is judged to be abnormal, or the vehicle speed signal communication malfunctions.

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Smart Key System Malfunction See Owner's Manual" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one of the following conditions is met)

    • 15 seconds have elapsed since the warning started.
    • The system returns to normal.

(12) Situation: The engine does not start. (Situation A)

  • When the driver's door is opened using the mechanical key and the engine switch is pressed, the electronic key transmitter subassembly cannot be detected inside the vehicle, or when the engine switch is pressed, the electronic key transmitter subassembly cannot be detected twice in succession.

    In this type of situation, the following operation is performed:

    Warning purpose

    Convenience function

    Warning start condition

    (one condition is met)

    • The engine immobilizer system is activated.
    • The electronic key transmitter is not inside the vehicle.
    • A key code verification error occurs when the engine switch is pressed twice, or during the unlock operation associated with the driver's door key.

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Depress Brake Pedal and Touch ENGINE Switch with Key" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one condition is met)

    • 60 seconds have elapsed since the warning started.
    • The electronic key transmitter subassembly is inside the vehicle. (The inside check is successful, or the check is successful when the transmitter battery is discharged and the electronic key transmitter subassembly has been touched to the engine switch).
    • The driver's door is opened using the front left outside door handle assembly and 30 seconds have elapsed.

(13) Situation: Immobilizer certification is completed.

  • When the transmitter battery is discharged, the smart key system is deactivated, or radio wave interference occurs, the electronic key transmitter subassembly is brought close to the engine switch.

    In this type of situation, the following operation is performed:

    Warning purpose

    Convenience function

    Warning start condition

    • The certification result of the electronic key transmitter subassembly is OK.

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Depress Brake Pedal & Push ENGINE Switch to Start" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one condition is met)

    • 10 seconds have elapsed since the warning started.
    • The electronic key transmitter subassembly is detected by the vehicle.
    • Engine speed is 500 rpm minimum.
    • The vehicle can be driven.
    • The immobilizer system is activated and key recognition is stopped, or the key cannot be recognized.

(14) Situation: The engine does not start. (Situation B)

  • There are 2 cases for this situation.
    • Sequence 1:

      The engine can be started (when the driver enters the vehicle or the engine switch is set to ON (ACC)).

      In this type of situation, the following operation is performed:

      Warning purpose

      Convenience function

      Warning start condition

      (one of the following conditions is met)

      • After the doors are unlocked from outside the vehicle with the engine switch in OFF, the driver's door is opened.
      • With the brake pedal not depressed, the engine switch is set to ON (ACC).

      Warning description

      (not displayed while the opening image is displayed).

      • "Depress Brake Pedal & Push ENGINE Switch to Start" is displayed on the multi-information display of the instrument cluster assembly.

      Warning stop condition

      (one condition is met)

      • 19 seconds have elapsed since the warning started.
      • The engine has started.
      • The doors are locked from outside the vehicle.
      • The doors are locked by a remote door lock operation from inside the vehicle.
    • Sequence 2:

      The engine can be started (when the engine switch is in the ON (IG) position).

      In this type of situation, the following operation is performed:

      Warning purpose

      Convenience function

      Warning start condition

      (one of the following conditions is met)

      • With the brake pedal not depressed, the engine switch is set to ON (IG) (the engine is not started).
      • The engine switch is in the ON (IG) position (the engine is not started) and the shift lever is moved from a position other than P or N to P or N.

      Warning description

      • "Not Ready to Drive Depress Brake Pedal & Push ENGINE Switch to Start" is displayed on the multi-information display of the instrument cluster assembly.

      Warning stop condition

      (one condition is met)

      • The power supply mode changes to a mode other than ON (IG).
      • The vehicle speed is at least 5 km/h.
      • The shift lever is placed in a position other than P or N.

(15) Situation: The engine switch cannot be set to OFF.

  • There are 2 cases for this situation.
    • Sequence 1:

      A warning message appears on the multi-information display when the driver tries to set the engine switch to OFF and the shift lever is in a position other than P

      In this type of situation, the following operation is performed:

      Warning purpose

      Battery discharge prevention, prevention of unintended vehicle movement

      Warning start condition

      • The engine switch is set to OFF with the shift lever in a position other than P or N (except for an emergency stop by pressing the engine switch 3 times quickly or holding the engine switch for at least 2 seconds).

      Warning description

      • The buzzer in the instrument cluster sounds once.
      • "Shift to P Before Exiting Vehicle" is displayed on the multi-information display of the instrument cluster.

      Warning stop condition

      (one of the following conditions is met)

      • The shift lever is placed in the P position.
      • The power supply mode changes to a mode other than ON (ACC).
    • Sequence 2:

      In the sequence 1 situation, the shift lever is moved to the P position.

      In this type of situation, the following operation is performed:

      Warning purpose

      Battery discharge prevention

      Warning start condition

      • The shift lever is placed in the P position.

      Warning description

      • The buzzer in the instrument cluster sounds once.
      • "Turn Power Off" is displayed on the multi-information display of the instrument cluster assembly.

      Warning stop condition

      (one of the following conditions is met)

      • The power supply mode changes to a mode other than ON (ACC).
      • The shift lever is in a position other than P.

(16) Situation: An automatic power supply off function operates.

  • A warning message appears on the multi-information display when the automatic power supply off function operates.

    In this type of situation, the following operation is performed:

    Warning purpose

    Convenience function

    Warning start condition

    (all conditions are met)

    • The shift lever is in P position.
    • The engine switch is in ON (ACC) or ON (IG) position.
    • No vehicle speed is detected and the engine is stopped.
    • The automatic power off function turns off the power supply mode. (20 minutes have elapsed with the engine switch in ON (ACC), or 1 hour has elapsed with the engine switch in ON (IG).)

    Warning description

    • "Auto Power Off to Conserve Battery" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one of the following conditions is met)

    • 10 seconds have elapsed since the warning started.
    • The engine switch is set to ON (ACC) or ON (IG).

(17) Situation: An electronic key transmitter subassembly has been registered.

  • A warning message appears on the multi-information display when an electronic key transmitter subassembly has been registered to the vehicle.

    In this type of situation, the following operation is performed:

    Warning purpose

    Convenience function

    Warning start condition

    (all conditions are met)

    • The engine switch is in OFF position.
    • The driver's door is unlocked and opened.
    • Within 10 days after registering a new key.

    Warning description

    • "A New Key has been Registered Contact Your Dealer for Details" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one condition is met)

    • 60 seconds have elapsed since the warning started.
    • All doors are closed and locked.
    • The engine switch is in the ON (IG) position.

(18) Situation: The shift lever is in a position other than P or N with the engine stopped.

  • A warning message is displayed on the multi-information display when the shift lever is in a position other than P or N while the engine switch is in ON (ACC) or ON (IG) and the engine is stopped.

    In this type of situation, the following operation is performed:

    Warning purpose

    Prevention of unintended vehicle movement

    Warning start condition

    (all conditions are met)

    • The engine switch is in the ON (IG) position.
    • No vehicle speed is detected.
    • The shift lever is in a position other than P or N.

    Warning description

    • The buzzer in the instrument cluster sounds once.
    • "Engine Stopped Shift to Position" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one condition is met)

    • The shift lever is placed in the P or N position.
    • The engine switch is in OFF position.
    • The vehicle speed is at least 5 km/h.

(19) Situation: The vehicle is moving with the engine switch in ON (IG) and the engine stopped.

  • A warning message appears on the multi-information display when the vehicle starts moving, the engine switch is in ON (IG), and the engine is stopped.

    In this type of situation, the following operation is performed:

    Warning purpose

    Prevention of unintended vehicle movement

    Warning start condition

    (all conditions are met)

    • The engine switch is in the ON (IG) position.
    • The shift lever is in a position other than P or N.
    • The engine is stopped.
    • The vehicle speed is at least 2 km/h.

    Warning description

    • The buzzer in the instrument cluster sounds continuously.
    • "Engine Stopped Stop in a Safe Place" is displayed on the multi-information display of the instrument cluster assembly.

    Warning stop condition

    (one condition is met)

    • The shift lever is placed in the N position.
    • The engine switch is in OFF position.
    • The engine has started.
    • No vehicle speed is detected.