Kia Stinger CK Quiz
Body Electrical System

Power Door Lock Module

In this manual: Body Electrical System
General Information — 8Maintenance — 27Engine Mechanical System — 47Engine Electrical System — 19Emission Control System — 12Engine Control System/Fuel System — 51Automatic Transmission System — 34All-Wheel Drive (AWD) System — 7Drive Shaft and Axle — 15Suspension System — 25Steering — 8Restraints — 19Brake System — 22Body (Interior and Exterior) — 47Front Seat Belt — 63Body Electrical System — 99Windshield Wiper/Washer — 11Heating, Ventilation, and Air Conditioning — 32
12steps
~72min
3/5difficulty
Done 0 of 12

Components and Component Location

Components

1. Door Lock/Unlock Handle Cable
2. Inside Door Handle Cable		 3. Door Latch Assembly

Repair Procedures

Inspection

Front Door Lock Module Inspection

  1. Remove the front door trim panel.

    (Refer to Body - "Front Door Trim Panel")

  2. Remove the front door module.

    (Refer to Body - "Front Door Module")

  3. Disconnect the actuator connector.

    [Central Locking]

    No. Terminal Information
    left Right Side
    1 - AJAR switch
    2 Motor 1 COM
    3 Motor 2 Lock/Unlock Switch
    4 - -
    5 - -
    6 Lock/Unlock Switch Motor 2
    7 COM Motor 1
    8 AJAR switch -

    [Dead Lock]

    No. Terminal Information
    left Right Side
    1 Motor 1 AJAR switch
    2 Motor 2 COM
    3 Motor 3 Lock/Unlock Switch
    4 Key unlock switch Key interlock switch
    5 Key interlock switch Key unlock switch
    6 Lock/Unlock Switch Motor 3
    7 COM Motor 2
    8 AJAR switch Motor 1

  4. Check the actuator operation by connecting power and ground as shown below. To avoid damaging the actuator, apply battery voltage only momentarily.

    [Central Lock (Without Key Switch)]

    [Dead Lock (Without Key Switch)]

    [Dead Lock (With Key Switch)]

    [Central Locking]

    [Dead Lock]

Rear Door Lock Module Inspection

  1. Remove the rear door trim.

    (Refer to Body - "Rear Door Trim Panel")

  2. Remove the rear door module.

    (Refer to Body - "Rear Door Module")

  3. Disconnect the actuator connector.

    [Central Locking]

    No. Terminal Information
    left Right Side
    1 - AJAR switch
    2 Motor 1 COM
    3 Motor 2 Lock/Unlock Switch
    4 - -
    5 - -
    6 Lock/Unlock Switch Motor 2
    7 COM Motor 1
    8 AJAR switch -

    [Dead Lock]

    No. Terminal Information
    left Right Side
    1 Motor 1 AJAR switch
    2 Motor 2 COM
    3 Motor 3 Lock/Unlock Switch
    4 - -
    5 - -
    6 Lock/Unlock Switch Motor 3
    7 COM Motor 2
    8 AJAR switch Motor 1

  4. Check the actuator operation by connecting power and ground as shown below. To avoid damaging the actuator, apply battery voltage only momentarily.

    [Central Lock (Without Key Switch)]

    [Dead Lock (Without Key Switch)]

    [Central Locking]

    [Dead Lock]

Rear Door Lock Module Inspection

  1. Remove the liftgate garnish.

    (Refer to Body - "Rear Door Trim")

  2. Disconnect the actuator connectors.

  3. Check the actuator operation by connecting power and ground as shown below. To avoid damaging the actuator, apply battery voltage only momentarily.

  4. Tailgate Power Supply Inspection refers to the trunk module.

Test yourself

A quick Kia Stinger CK quiz: every answer comes with an explanation and a link to the manual page.