Kia Stinger CK Quiz
Body Electrical System

Indicators and Sensors

In this manual: Body Electrical System
General Information — 8Maintenance — 27Engine Mechanical System — 47Engine Electrical System — 19Emission Control System — 12Engine Control System/Fuel System — 51Automatic Transmission System — 34All-Wheel Drive (AWD) System — 7Drive Shaft and Axle — 15Suspension System — 25Steering — 8Restraints — 19Brake System — 22Body (Interior and Exterior) — 47Front Seat Belt — 63Body Electrical System — 99Windshield Wiper/Washer — 11Heating, Ventilation, and Air Conditioning — 32
37steps
~222min
4/5difficulty
Done 0 of 37

Components and Component Location

Components

Standard Type ("3.5 inch")

Super Vision Type ("7 inch")

Connector Pin Information

No. Description No. Description
1 Ground (Signal 3) 21 Dimmer Switch (-)
2 Illumination (-) 22 Switch 1 (+)
3 Rheostat Switch (Down)_Input 23 Switch 2 (+)
4 Rheostat Switch (Up)_Input 24 Driver Mode Switch (CW) _ Input
5 Dent 25 Driver Mode Switch (CCW) _ Input
6 AT ("P" Position) 26 Cluster Speaker (+)
7 AT ("R" Position) 27 Cluster Speaker (-)
8 AT ("N" Position) 28 -
9 AT ("D" Position) 29 Multimedia CAN (Low)
10 AT ("S" Position) 30 Multimedia CAN (High)
11 - 31 Engine Running Status_Output
12 Vehicle Speed_Output 32 Chassis CAN (High)
13 - 33 Chassis CAN (Low)
14 Fuel Sender (+)_Input 34 -
15 Water separator input (diesel only) 35 -
16 Fuel Sender (-)_Input 36 -
17 Water separator input (diesel only) 37 Ground (Signal 1)
18 AIRBAG (+) _ Input 38 -
19 Oil pressure switch input (gasoline only) 39 IGN 1
20 - 40 Battery (+)

Circuit Diagrams

Wiring Diagram

Standard Type ("3.5 inch")

Super Vision Type ("7 inch")

Description and Operation

Description

Communication Network Diagram

Abbreviation Description
ACU Airbag Control Unit
AFT Adaptive Front Lighting System
AMP Amplifier
AUDIO Audio head unit
AVM Around View Monitor
B_CAN Body Controller Network
BCW Blind-Spot Collision Warning
C_CAN Chassis Controller Area Network
CDP CD Player
CLU Cluster Module
DATC Dual Automatic Temperature Control
DDM Driver door module
ECM Engine Control Module
F_PUMP Fuel Pump Control Module
HUD Projection Display
IBU Intelligent Body Control Unit
ICU (Intensive Care Unit) Integrated Central Control Unit
IFB Interface Unit
IMS Integrated Memory System
LDW Lane Departure Warning
LKA Ground care assistance
M_CAN Multimedia Controller Network
MDPS Motor Driven Power Steering
MFC Multi-Function Camera
MTS Manual Temperature Control
ORV Passenger Sensing System
P_CAN Power Train Controller Area Network
PCM Powertrain Control Module
PTG Power Liftgate Module
RVM Rear View Monitor
CCS Smart Cruise Control
SKM Steering Column Module
TCM Transmission Control Module
VDC Vehicle Dynamic Control
VPC Wireless Charger

Cluster Variant Coding

Since the vehicle has more options (ESC, MDPS, etc.), the instrument cluster now has more information to display depending on the selected options.

For this reason, it is necessary to determine which options the vehicle has when replacing the instrument cluster.

To solve this problem, a coding procedure based on the options required for the vehicle should be performed when replacing the instrument cluster.

This is called variant coding.

Function

  1. High-Speed CAN Communication (C-CAN)

    • User Function: Auto Seats linked to Entry/Exit Movement, Welcome Light

    • LDW: Lane Departure Warning

    • LKA: Lane Keeping Assist

    • PA: Parking Assist

    • PDW: Park Distance Warning

  2. Low-speed CAN communication (M-CAN)

    • AV: Audio/Video Multimedia Information Display

    • TBT: Turn-by-Turn Navigation Information Display

  3. Various Source Control

    Various warning alarms and sound effects are output through external speakers connected to the instrument cluster.

    Sound Description and Function (CAN Data Receiver)
    Welcome Welcome (key removed and door open/closed, verified by IBU).
    Goodbye Goodbye (Cluster)
    Open Door Warning Key warning (IBU), vehicle speed 5 km/h or below and IGN switch in ACC or IGN, or engine start, and when vehicle speed is below 5 km/h, or driver door open
    Unfastened Seat Belt Warning Driver seat belt unfastened warning (IBU)
    PDW system warning PDW sensor malfunction warning (IBU)
    R Gear PDW warning when shifting to R (reverse) (IBU and PA)
    Parking Brake Parking brake warning (IBU)
    Start Button SSB button warning (IBU)
    Rheostat Light Information Rheostat Warning When Maximum or Minimum Level Is Selected (Cluster)
    Smart Key Transmission Smart key not detected warning (IBU)
    Smart Cruise Changeover from Normal Cruise to Smart Cruise (SCC)
    Smart Cruise Driving Information Smart Cruise (SCC) Function Cancellation
    Normal Cruise Changeover from Smart Cruise to Normal Cruise (SCC)
    Turn Signal Lamp (Check Mark) Turn signal lamp indicator warning (IBU)
    Turn Signal Lamp (Tock) Turn signal lamp indicator warning (IBU)
    Smart Key Low Battery Voltage Warning when the driver presses the SSB button with a low-voltage smart key battery (IBU)
    EPB Warning Warning When Changing from Auto Hold to EPB Lock (EPB)
    Coolant Temperature Warning When Engine Temperature Is Above 120 °C

  4. User Setting Mode (USM)

    The settings can be changed using the tactile switch menu and the CW, CCW, and OK buttons (or the UP, DOWN, LEFT, RIGHT, and OK buttons of the general switch). There are a total of 24 items (for example, Entry/Exit Seat Synchronization, Steering Wheel Synchronization, Auto Door Lock, Auto Door Unlock, Headlamp Follow-Me, Welcome Light, Welcome Sound, Triple Turn Signal, Average Fuel Consumption Auto Reset, HUD Height, Brightness, and Content Setup) that can be set and adjusted. The signal flow during setup is as follows.

    1. USM settings are configured and transmitted to the IBU.

    2. The IBU transmits the settings over B-CAN to the corresponding modules.

    3. The module completes the setup and transmits the changed setting to the MSB.

    4. The IBU transmits the final settings to the cluster over the C-CAN bus.

Troubleshooting

Troubleshooting

Error Item Failure Symptom Check Items Detailed Checks Related Parts/
Components
On-Screen Display LCD screen does not turn on

  1. Connecting Fixtures

  2. Components

  1. Check Connector Mounting

  2. Check B+, IGN and GND wiring.

  3. Check Components

 Connectors, Wiring, Fuses, Instrument Cluster
Warning Light Airbag Warning Lamp Malfunction

  1. Connecting Fixtures

  2. C-CAN

  3. Components

  1. Check Airbag + Signal (Connectors)

  2. Check C-CAN Signal (ACU4)

  3. Check FPC attachment inside the instrument cluster.

 ACU Connectors, Wiring, Fuses, Instrument Cluster
Mode Conversion Built-in Drive Mode Malfunction

  1. Connecting Fixtures

  2. Switch

  3. Components

  1. Check Switch Input (Connector)

  2. Check the switch input signal

    (open or short circuit)

  3. Check Conversion Using Cluster Component

 Switch Connector, Cluster Wiring
Illumination Interior Illumination Brightness Cannot Be Adjusted.

  1. Connecting Fixtures

  2. Switch

  3. Components

  1. Check whether the light switch input signal reaches the connector

  2. Check ILL- and DETENT signals

  3. Check TAIL+ signal input

 Switch Connector, Cluster Wiring
Warning Sound No Warning Chime on Instrument Cluster

  1. Connecting Fixtures

  2. Car Speakers

  3. Components

  1. Check the speaker output connector

  2. Check the vehicle speakers

 Speaker connectors, instrument panel wiring
Fuel Gauge Incorrect fuel level gauge indication

  1. Connecting Fixtures

  2. Fuel Sender

  3. Components

  1. Check the fuel input and GND connectors.

    (open, short circuit, or input resistance values)

  2. Check the fuel sender

 Fuel level sender connector, instrument panel wiring

Test yourself

A quick Kia Stinger CK quiz: every answer comes with an explanation and a link to the manual page.