ECU Terminals
ECU TERMINALS
INSPECT TRANSPONDER KEY ECU ASSEMBLY
(a) Disconnect connector F22 from the transponder key ECU assembly.
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Tester Connection | Input/Output | Wire Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
F22-1 (+B) - F22-5 (GND) |
Input |
W - W-B |
Battery |
Always |
11 à 14 V |
+B |
F22-2 (IG) - F22-5 (GND) |
Input |
B - W-B |
Ignition switch signal |
Ignition Switch in OFF position |
Below 1 V |
IG SW |
Ignition Switch in ON position |
11 à 14 V |
|||||
F22-3 (KSW) - F22-5 (GND) |
Input |
V - W-B |
Unlock warning switch signal |
No key in ignition key cylinder |
10 kΩ minimum |
Key SW/B2780 |
Key in ignition key cylinder |
Below 1 Ω |
|||||
F22-5 (GND) - Body ground |
- |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
- |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Reconnect connector F22 to the transponder key ECU assembly.
(d) Measure the voltage and check the pulses according to the value(s) in the table below.
Tester Connection | Input/Output | Wire Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
F22-8 (IND) - F22-5 (GND) |
Output |
P - W-B |
Security indicator signal |
No key in ignition key cylinder, or 20 s have elapsed after the ignition switch was turned to ACC or OFF (immobiliser system activated) |
Pulse generation |
Immobiliser |
Key in ignition key cylinder (immobiliser system deactivated) |
Below 1 V |
|||||
F22-9 (D) - F22-5 (GND) |
Input/Output |
SB - W-B |
DLC3 communication |
No communication |
Below 1 V |
- |
During communication |
Pulse generation |
|||||
F22-4 (ANT1) - F22-5 (GND) |
Input/Output |
V - W-B |
Power supply for transponder key amplifier. |
No key in ignition key cylinder |
4 à 6 V |
- |
Within 3 seconds after inserting the key into the ignition key cylinder |
Pulse generation (See waveform 1) |
|||||
F22-15 (ANT2) - F22-5 (GND) |
Input/Output |
W - W-B |
Transponder key amplifier communication signal |
No key in ignition key cylinder |
4 à 6 V |
- |
Within 3 seconds after inserting the key into the ignition key cylinder |
Pulse generation (see waveform 2) |
|||||
F22-12 (EFII) - F22-5 (GND) |
Output |
G - W-B |
ECM input signal |
Within 3 seconds after cranking and initial combustion, or within 3 seconds after the ignition switch is first turned ON following disconnection and reconnection of the negative (-) battery terminal |
Pulse generation (See waveform 3) |
- |
F22-13 (EFIO) - F22-5 (GND) |
Input |
R - W-B |
ECM output signal |
Ignition Switch in OFF position |
Below 1 V |
- |
Ignition Switch in ON position |
Pulse generation (see waveform 4) |
If the result is not as specified, the transponder key ECU assembly may be faulty.
(e) Check the waveform using an oscilloscope.
(1) Waveform 1 (Reference)
Tester Connection |
F22-4 (ANT1) - F22-5 (GND) |
Oscilloscope Setting |
20 V/DIV., 2 s/DIV. |
Condition |
Within 3 seconds after inserting the key into the ignition key cylinder |
(2) Waveform 2 (Reference)
Tester Connection |
F22-15 (ANT2) - F22-5 (GND) |
Oscilloscope Setting |
20 V/DIV., 2 s/DIV. |
Condition |
Within 3 seconds after inserting the key into the ignition key cylinder |
(3) Waveform 3 (Reference)
*a |
Approximately 160 ms |
*b |
Approximately 270 ms |
Tester Connection |
F22-12 (EFII) - F22-5 (GND) |
Oscilloscope Setting |
2 V/DIV., 500 ms/DIV. |
Condition |
Within 3 seconds after cranking and initial combustion, or within 3 seconds after the ignition switch is first turned ON following disconnection and reconnection of the negative (-) battery terminal |
(4) Waveform 4 (reference)
*a |
Approximately 160 ms |
*b |
Approximately 270 ms |
Tester Connection |
F22-13 (EFIO) - F22-5 (GND) |
Oscilloscope Setting |
2 V/DIV., 500 ms/DIV. |
Condition |
Ignition Switch in ON position |
CHECK ECM
(a) Measure the voltage and resistance, and check the pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Input/Output | Wire Color | Terminal Description | Condition | Specified Condition | Corresponding Data List item/DTC |
|---|---|---|---|---|---|---|
C63-59 (E1) - Body ground |
- |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
- |
A38-45 (IMO) - C63-59 (E1) |
Output |
GR - W-B |
ID code box (immobilizer code ECU) communication output |
Ignition Switch in OFF position |
11 à 14 V |
- |
A38-45 (IMO) - C63-59 (E1) |
Output |
GR - W-B |
ID code box (immobilizer code ECU) communication output |
Within 3 seconds after engine start, or within 3 seconds after the ignition switch is turned ON following disconnection and reconnection of the battery cable |
Pulse generation (See waveform 1) |
- |
A38-28 (IMI) - C63-59 (E1) |
Input |
BE - W-B |
ID code box (immobilizer code ECU) communication input |
Ignition Switch in OFF position |
11 à 14 V |
- |
A38-28 (IMI) - C63-59 (E1) |
Input |
BE - W-B |
ID code box (immobilizer code ECU) communication input |
Ignition switch turned ON using the registered electronic key transmitter subassembly |
Pulse generation (see waveform 2) |
- |
(b) Check the waveform using an oscilloscope.
NOTICE:
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
(1) Waveform 1 (Reference)
*a |
Approximately 160 ms |
*b |
Approximately 270 ms |
Item | Content |
|---|---|
Tester Connection |
A38-45 (IMO) - C63-59 (E1) |
Oscilloscope Setting |
2 V/DIV., 500 ms/DIV. |
Condition |
Within 3 seconds after engine start, or within 3 seconds after the ignition switch is turned ON following disconnection and reconnection of the battery cable |
(2) Waveform 2 (Reference)
*a |
Approximately 160 ms |
*b |
Approximately 270 ms |
Item | Content |
|---|---|
Tester Connection |
A38-28 (IMI) - C63-59 (E1) |
Oscilloscope Setting |
2 V/DIV., 500 ms/DIV. |
Condition |
Ignition switch turned ON using the registered electronic key transmitter subassembly |