How to Use Troubleshooting
PRECAUTION / NOTICE / HINT
HINT:
- Follow this procedure to troubleshoot the immobilizer system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
HINT:
- When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
- Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
- The following 5 elements are essential for analyzing the problem:
What |
Vehicle model, system name |
When |
Date, time, frequency of occurrence |
Where |
If the problem occurs at a specific location |
What were the conditions? |
If the doors are locked or unlocked, if the power switch is ON, or if the engine is running. |
How did it happen? |
Problem Symptoms |
|
CHECK BATTERY VOLTAGE
(a) Measure the battery voltage.
Standard voltage:
11 à 14 V
If the voltage is below 11 V, charge or replace the battery before proceeding to the next step.
|
CRANK THE ENGINE FOR MORE THAN 10 SECONDS
|
CHECK DTCs* (ECM)
(a) Check whether DTCs are output and record them.
Powertrain > Engine and ECT > Trouble CodesHINT:
Before performing the DTC check, perform the "DTC Output Confirmation Check" of each diagnostic procedure.
Result:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
DTCs related to the SFI system are output (without fuel vapor absorber pump module) |
B |
DTCs related to the SFI system are output (with fuel vapor absorber pump module) |
C |
DTCs related to the immobilizer system are output |
D |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| C | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| D | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
CHECK DTCs* (TRANSPONDER KEY ECU ASSEMBLY)
(a) Check whether DTCs are output and record them.
Body Electrical > Immobiliser > Trouble CodesHINT:
Before performing the DTC check, perform the "DTC Output Confirmation Check" of each diagnostic procedure.
Result:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
DTCs related to the immobilizer system are output |
B |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
SYMPTOM TROUBLESHOOTING TABLE
(a) Refer to the Symptom Troubleshooting Table.
Click here![]()
Result:
Result | Proceed to |
|---|---|
The malfunction is not listed in the Problem Symptoms Table |
A |
The malfunction is listed in the Problem Symptoms Table |
B |
| B | GO TO STEP 9 |
|
GENERAL ANALYSIS AND TROUBLESHOOTING*
(a) Data List / Active Test.
Click here![]()
(b) ECU terminals.
Click here![]()
|
REPAIR OR REPLACE
HINT:
If the Transponder Key ECU Assembly, ECM or key is replaced, refer to the registration procedure.
Click here![]()
|
CHECK DTCs*
(a) Clear the DTCs.
Body Electrical > Immobiliser > Clear DTCs Powertrain > Engine and ECT > Trouble Codes(b) Check DTCs.
Body Electrical > Immobiliser > Trouble Codes Powertrain > Engine and ECT > Clear DTCsHINT:
Before performing the DTC check, perform the "DTC Output Confirmation Check" of each diagnostic procedure.
Result:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
DTCs related to the immobilizer system are output |
B |
| A | END |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |