Theft Deterrent / Keyless Entry

Transponder Chip Malfunction (B2793, B2794, B2797, B2798)

~4min read

DESCRIPTION

  • DTC B2793 is stored when a malfunction is detected in the key during key ID code registration, or when the key ID code is not registered normally. Replace the key if key ID code registration does not complete normally and this DTC is output.
  • DTC B2794 is stored when a key with an incomplete key ID code is inserted into the key cylinder.
  • DTC B2797 is stored when a key with a BCC malfunction is inserted into the key cylinder.
  • DTC B2798 is stored when a key is inserted into the key cylinder and a communication error occurs between the key and the transponder key ECU assembly.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2793

Transponder chip malfunction

Transponder chip malfunction (1 trip detection logic*).

  • Key
  • Transponder Key Coil
  • Transponder Key ECU Assembly
  • Insert the key into the key cylinder.

B2794

Encryption code not matched

A key with an incomplete key ID code is inserted into the key cylinder (1 trip detection logic*).

  • Key
  • Transponder Key Coil
  • Transponder Key ECU Assembly
  • Insert the key into the key cylinder.

B2797

Communication malfunction No. 1

A key with a BCC malfunction is inserted into the key cylinder (1 trip detection logic*).

  • Key
  • Transponder Key Coil
  • Transponder Key ECU Assembly
  • Insert the key into the key cylinder.

B2798

Communication malfunction No. 2

Key ID code identification cannot be completed within the specified time (1 trip detection logic*).

  • Key
  • Transponder Key Coil
  • Transponder Key ECU Assembly
  • Insert the key into the key cylinder.
  • *: Output only when a malfunction is detected.
Vehicle condition and fail-safe function when a malfunction is detected

Vehicle Condition When Malfunction Is Detected

Fail-safe function when a malfunction is detected

The engine does not start.

-

Related Data List and Active Test

DTC No.

Data List and Active Test

B2793

-

B2794

-

B2797

-

B2798

-

PRECAUTION / NOTICE / HINT

NOTICE:

  • If the transponder key ECU assembly or key is replaced, refer to the Registration section.

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

PROCEDURE

  1. CLEAR DTCs

(a) Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Insert and remove each registered key one at a time, and check whether DTCs are output each time.

Body Electrical > Immobiliser > Trouble Codes

HINT:

  • Before checking the DTCs, perform the "DTC Output Confirmation Operation" procedure.
  • If DTC B2793, B2794, B2797, or B2798 is stored, clear the DTCs before checking the next key.

OK:

DTCs B2793, B2794, B2797 and B2798 are not output.

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output for all keys

B

DTCs are output for all keys

C

A

USE SIMULATION METHOD TO CHECK

C

REPLACE THE KEY FOR WHICH THE DTC IS OUTPUT

B
  1. CHECK CONNECTOR CONNECTION

(a) Make sure the connectors are properly connected to the transponder key coil.

(b) Check whether the engine starts with the key.

OK:

The engine starts.

OK

END (CONNECTOR WAS NOT PROPERLY CONNECTED)

NG
  1. REPLACE TRANSPONDER KEY COIL

(a) Replace the transponder key coil.

Click here

(b) Check whether the engine starts with the key.

OK:

The engine starts.

OK

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY