Registration
REGISTRATION
PROCEDURE
1. CODE REGISTRATION DESCRIPTION
(a) The door control transmitter assembly has 2 codes: the key code (immobiliser code) and the remote control code. Both codes must be registered. For remote code registration procedures, refer to the Remote Control Power Door Lock System.
Click here![]()
2. KEY REGISTRATION PROCEDURES WHEN ADDING OR REPLACING A KEY, OR WHEN A KEY IS LOST
HINT:
- The procedures described below require the use of Techstream:
- - Registering a new key code
- - Registering additional key codes
- - Key code erasure
- A maximum of 5 key codes can be registered.
Customer request / Condition | Registration procedure status | Procedure | Refer to items |
|---|---|---|---|
Registering an additional door control transmitter assembly |
The customer must bring at least 1 door control transmitter assembly. |
1. Register additional door control transmitter assemblies if necessary (registering an additional key code). |
PROCEDURE "B" |
HINT: After key code erasure, all remaining door control transmitter assemblies that are not registered at this point cannot be used. Therefore, after key code erasure, register all remaining door control transmitter assemblies. |
The customer must bring at least 1 door control transmitter assembly. |
1. Using the remaining door control transmitter assembly, erase all registered door control transmitter assemblies except one (key code erasure). |
PROCEDURE "C" |
2. Register additional door control transmitter assemblies if necessary (registering an additional key code). |
PROCEDURE "B" |
||
All door control transmitter assemblies are lost |
- |
1. Reset all door control transmitter assemblies (erase the ID of all keys (key code reset)). |
PROCEDURE "D" |
2. Register all door control transmitter assemblies (register the ID of a new key). |
PROCEDURE "A" |
3. PARTS REPLACEMENT AND KEY REGISTRATION PROCEDURES
(a) The following table shows the ECU and key registration replacement procedures for cases where an ECU has been confirmed faulty during immobiliser system troubleshooting.
HINT:
- The procedures described below require the use of Techstream:
- - Registering a new key code
- - Registering additional key codes
- - Key code erasure
- A maximum of 5 key codes can be registered.
ECU malfunction | Procedure | Refer to items |
|---|---|---|
Transponder Key ECU Assembly |
1. Replace the transponder key ECU assembly. |
Click here |
2. Register all door control transmitter assemblies. |
PROCEDURE "A" |
|
3. Register the ECU communication ID. |
PROCEDURE "E" |
|
ECM |
1. Replace the ECM. |
Click here |
2. Register the ECU communication ID. (When replacing the ECM with a used part) |
PROCEDURE "F" |
|
Transponder key ECU assembly and ECM |
1. Replace the transponder key ECU assembly. |
Click here |
2. Replace the ECM. |
Click here |
|
3. Register all door control transmitter assemblies. |
PROCEDURE "A" |
|
4. Register the ECU communication ID. (When replacing the ECM with a used part) |
PROCEDURE "F" |
4. KEY REGISTRATION (PROCEDURE "A")
(a) Registering a new key code (procedure "A"):
NOTICE:
Make sure that no key code is registered in the transponder key ECU assembly.
HINT:
- In this mode, a maximum of 2 master key codes can be registered. Master keys can be registered in any order because the transponder key ECU assembly can distinguish between different types of door control transmitter assemblies.
- New key codes must be registered with the battery connected. The ignition switch can be in either the ON or OFF position.
- When installing a new transponder key ECU assembly, the key codes must be registered in the transponder key ECU assembly.
Procedure | Security indicator light status |
|---|---|
1. Start |
Flashes HINT: Until the first door control transmitter assembly is inserted |
2. Insert the master key into the ignition switch. |
Flashes |
3. Techstream operation Select the following menus: Body Electrical / Immobiliser / Utility / Key Registration HINT: After completing the operation described above, proceed to the next step according to the instructions displayed on the Techstream screen. |
OFF for 1 second, then ON |
4. Remove the door control transmitter assembly, then select Next on the Techstream. |
ON |
5. Insert the master key to be registered, then select Next on the Techstream. |
OFF for 1 second, ON for 0.5 second, then OFF |
6. Remove the door control transmitter assembly. |
Flashes |
7. End |
|
HINT:
- When the immobiliser system is operating normally and the door control transmitter assembly is removed, the security indicator light flashes continuously.
- If registration of the new key code fails, code 2-1 is output by the security indicator light. Attempting to re-register a door control transmitter assembly that is already registered causes code 2-2 to be output when the door control transmitter assembly is inserted. If the number of registered key codes exceeds the maximum limit, the security indicator light will display code 2-3. The output data is shown below.
(b) Ending the automatic key code registration mode:
The automatic key code registration mode can be ended once at least 1 key code (immobiliser code) has been registered.
HINT:
Follow the instructions displayed on the Techstream screen to end the new key code registration mode.
5. KEY REGISTRATION (PROCEDURE "B")
(a) Additional registration (procedure "B"):
HINT:
- A maximum of 5 master key codes can be re-registered.
- The additional key code registration is cancelled if any step is not completed within the specified time.
- When replacing the ignition key cylinder or the key cylinder set, remove the transmitter module from the original master key. Then install the transmitter module into a new key and use it as the master key. If necessary, use this master key to register other door control transmitter assemblies.
NOTICE:
When the ignition key cylinder has been replaced, the doors can only be locked and unlocked with the transmitter module of the new master key (taken from the original master key). However, the doors cannot be locked or unlocked with the new master key at the door lock. Keep the original master key. If the battery of the transmitter module in the new master key is discharged, the original master key can be used to lock or unlock the door lock cylinder.
Additional registrationProcedure | Time to complete operation | Security indicator light status |
|---|---|---|
1. Start |
- |
Flashes HINT: Until the first door control transmitter assembly is inserted |
2. Insert the registered master key into the ignition key cylinder and turn the ignition switch to ON. |
Within 120 seconds |
OFF |
3. Techstream operation Select the following menus: Body Electrical / Immobiliser / Utility / Key Registration HINT: After completing the operation described above, proceed to the next step according to the instructions displayed on the Techstream screen. |
ON |
|
4. Remove the master key. |
Within 20 seconds HINT: After Techstream instruction |
ON |
5. Insert the door control transmitter assembly to be registered into the ignition key cylinder. |
Within 10 seconds |
Flashes |
6. After 60 seconds, the door control transmitter assembly is registered. HINT: The security indicator turns off to indicate that the door control transmitter assembly has been registered. |
- |
OFF |
7. Remove the door control transmitter assembly. |
- |
Flashes |
8. End |
||
HINT:
- A brief description of the key code registration procedure is given above. For more detailed information, refer to the Techstream screen.
- When the immobiliser system is operating normally and the door control transmitter assembly is removed, the security indicator light flashes continuously.
- If key code registration fails while registering an additional key code, DTC 2-1 is output by the security indicator. Attempting to re-register a door control transmitter assembly that is already registered outputs DTC 2-2 when the door control transmitter assembly is inserted into the ignition key cylinder. If the number of registered key codes exceeds the maximum limit, the security indicator displays DTC 2-3. Details of code output are given in procedure "A".
6. KEY REGISTRATION (PROCEDURE "C")
(a) Key code erasure (procedure "C"):
HINT:
- When this procedure is performed, all key codes are erased except that of the master key, which is used to erase the other key codes. To use a door control transmitter assembly whose code has been erased, a new key code must be registered.
- This procedure is cancelled if each step is not completed within the specified time.
Procedure | Time to complete operation | Security indicator light status |
|---|---|---|
1. Start |
- |
Flashes HINT: Until the first door control transmitter assembly is inserted |
2. Insert the registered master key into the ignition key cylinder and turn the ignition switch to ON. |
Within 120 seconds |
OFF |
3. Techstream operation Select the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure HINT: After completing the operation described above, proceed to the next step according to the instructions displayed on the Techstream screen. |
On for 1 second, then off |
|
4. Remove the master key. |
Within 10 seconds HINT: After Techstream instruction |
Flashes |
5. End |
||
HINT:
- A brief description of the key code registration procedure is given above. For more detailed information, refer to the Techstream screen.
- When the immobiliser system is operating normally and the door control transmitter assembly is removed, the security indicator light flashes continuously.
7. KEY REGISTRATION (PROCEDURE "D")
(a) Erase all key codes (procedure "D"):
HINT:
- To perform this procedure, at least 1 door control transmitter assembly must be registered in the transponder key ECU assembly.
- This procedure can be performed using either a registered or an unregistered door control transmitter assembly.
Procedure | Time to complete operation | Security indicator light status |
|---|---|---|
1. Start |
- |
Flashes |
2. Insert the registered master key or an unregistered door control transmitter assembly into the ignition key cylinder and turn the ignition switch to ON. |
Within 10 minutes |
ON or OFF |
3. Using TIS, confirm that the user and the vehicle match. |
||
4. Techstream operation Select the following menus: Body Electrical / Immobiliser / Utility / Immobiliser Code Reset HINT: After completing the operation described above, proceed to the next step according to the instructions displayed on the Techstream screen. |
Within 15 minutes |
On for 1 second, then off |
5. The end message for erasing all key codes is displayed. |
- |
ON |
6. End |
||
HINT:
- A brief description of the key code registration procedure is given above. For more detailed information, refer to the Techstream screen.
- When the immobiliser system is operating normally and the door control transmitter assembly is removed, the security indicator light flashes continuously.
8. KEY REGISTRATION (PROCEDURE "E")
(a) ECU communication ID registration (procedure "E"):
NOTICE:
- When replacing the transponder key ECU assembly, the ECM's ECU communication ID must be registered in the transponder key ECU assembly to match the ECU communication IDs.
- The engine will not start if the ECU communication IDs do not match.
- Do not turn the ignition switch from ON to OFF 20 times or more before registering the ECU communication ID. Turning the ignition switch from ON to OFF 20 times or more may prevent the engine from starting unless the transponder key ECU assembly is replaced with a new one.
- After registration, turning the ignition switch to START may prevent the engine from starting on the first attempt. If this occurs, turn the ignition switch to ON again.
- After the engine starts, clear DTC B2799 (ECM immobiliser communication error code) using one of the following methods:
- Using Techstream
- Disconnect the battery for 30 seconds
(1) Using the SST, connect terminals TC and CG of the DLC3. SST: 09843-18040 |
|
(2) Turn the ignition switch to ON and leave the vehicle as is for 30 minutes.
NOTICE:
Do not open or close any door. If a door is opened and then closed, restart the registration from step 1.
HINT:
Do not start the engine.
(3) Make sure the engine starts.
9. KEY REGISTRATION (PROCEDURE "F")
(a) ECU communication ID registration (procedure "F"):
NOTICE:
The ECU communication ID must be registered when the transponder key ECU assembly and the ECM are replaced, or when only the ECM is replaced, to match the ECU communication ID.
ECU communication ID registrationProcedure | Security indicator light status |
|---|---|
1. Start |
OFF |
2. Insert a registered door control transmitter assembly into the ignition key cylinder. |
|
3. Start the engine. |
|
4. Make sure the engine starts and runs for more than 3 seconds. |
|
5. End |
|
