Theft Deterrent / Keyless Entry

Immobiliser System Malfunction (B2799)

~7min read

DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and the transponder key ECU assembly malfunctions, or when the communication ID of the ECM and the transponder key ECU assembly do not match.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2799

Immobiliser system malfunction

One of the following conditions is met (1 driving cycle(s)*2 detection logic):

  • If a malfunction occurs in the communication or communication lines between the ECM and the transponder key ECU assembly.
  • A communication code cannot be checked during communication between the ECM and the transponder key ECU assembly.
  • Wire harness or connector
  • Transponder Key ECU Assembly
  • ECM
DTC Output Confirmation Operation:
  • Start the engine and wait 10 seconds.*1
  • After disconnecting and reconnecting the cable from the negative (-) battery terminal, turn the ignition switch ON and wait 10 seconds*2.

    *1: Communication starts within 3 seconds after the engine starts. If the check fails, this DTC is stored 6 seconds after communication ends.

    *2: Communication starts within 3 seconds after the ignition switch is turned ON. If the check fails, this DTC is stored 6 seconds after communication ends.

DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

Engine start operation.

○

○

Malfunction Status

If a malfunction occurs in the communication or communication lines between the ECM and the transponder key ECU assembly.

○

-

A communication code cannot be checked during communication between the ECM and the transponder key ECU assembly.

-

○

Detection Duration

-

-

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

Vehicle condition and fail-safe function when a malfunction is detected

Vehicle Condition When Malfunction Is Detected

Fail-safe function when a malfunction is detected

The engine does not start.

-

Related Data List and Active Test

DTC No.

Data List and Active Test

B2799

-

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the transponder key ECU assembly, refer to the Registration section.

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

If transponder key ECU assembly DTCs are output at the same time, troubleshoot the transponder key ECU assembly DTC first.

PROCEDURE

  1. CLEAR DTCs

(a) Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Start the engine.

(b) Check DTCs.

Powertrain > Engine and ECT > Trouble Codes

HINT:

Before checking the DTCs, perform the "DTC Output Confirmation Operation" procedure.

OK:

DTC B2799 is not output.

Result:

Result

Proceed to

OK

A

NG (DTC B2799 is output)

B

NG (other DTCs are output)

C

A

USE SIMULATION METHOD TO CHECK

C

GO TO DIAGNOSTIC TROUBLE CODE CHART

B
  1. CHECK ECM (IMO TERMINAL)

(a) Check the waveform using an oscilloscope.

*a

Component with Wire Harness Connected

(ECM)

*b

Waveform

Measurement Condition

Item

Content

Tester Connection

A38-45 (IMO) - Body ground

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Within 3 seconds after cranking and initial combustion, or within 3 seconds after the ignition switch is first turned ON following disconnection and reconnection of the negative (-) battery terminal

Result:

Result

Proceed to

OK

A

NG (IMO terminal stuck low (2.4 V max.))

B

NG (IMO terminal stuck high (12 V) or abnormal waveform)

C

B

GO TO STEP 10

C

GO TO STEP 7

A
  1. CHECK ECM (IMI TERMINAL)

(a) Check the waveform using an oscilloscope.

*a

Component with Wire Harness Connected

(ECM)

*b

Waveform

Measurement Condition

Item

Content

Tester Connection

A38-28 (IMI) - Body ground

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Ignition Switch in ON position

OK:

The waveform is the same as that shown in the diagram.

Result:

Result

Proceed to

OK

A

NG

B

B

GO TO STEP 12

A
  1. REGISTER ECU COMMUNICATION ID

(a) Re-register the ECU communication ID.

HINT:

Refer to Registration.

Click here

NEXT
  1. CHECK WHETHER THE ENGINE STARTS

(a) Using a registered key, turn the ignition switch ON.

(b) Make sure the engine starts 5 seconds after turning the ignition switch ON.

OK:

The engine starts normally.

OK

END (COMMUNICATION ID REGISTRATION FAILED)

NG
  1. REPLACE ECM

(a) Temporarily replace the ECM with a new one.

Click here

NEXT
  1. REGISTER ECU COMMUNICATION ID

(a) Re-register the ECU communication ID.

HINT:

Refer to Registration.

NEXT
  1. CHECK WHETHER THE ENGINE STARTS

(a) Using a registered key, turn the ignition switch ON.

(b) Make sure the engine starts 5 seconds after turning the ignition switch ON.

OK:

The engine starts normally.

OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

  1. CHECK ECM (IMO TERMINAL VOLTAGE)

(a) Disconnect the A38 ECM connector.

(b) Turn the ignition switch ON.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Result

A38-45 (IMO) - Body ground

Ignition switch turned ON using the registered key

IMO terminal is stuck low (2.4 V max.)

IMO terminal stuck high (12 V) or abnormal waveform

*a

Front view of wire harness side connector

(to ECM)

Result:

Result

Proceed to

IMO terminal is stuck low (2.4 V max.)

A

IMO terminal stuck high (12 V) or abnormal waveform

B

B

GO TO STEP 7

A
  1. CHECK WIRE HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)

(a) Disconnect connector F22 from the transponder key ECU assembly.

(b) Disconnect connector A38 from the ECM.

(c) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F22-12 (EFII) - A38-45 (IMO)

Always

Below 1 Ω

A38-45 (IMO) - Body ground

Always

10 kΩ minimum

F22-12 (EFII) - Body ground

Always

10 kΩ minimum

F22-13 (EFIO) - A38-28 (IMI)

Always

Below 1 Ω

A38-28 (IMI) - Body ground

Always

10 kΩ minimum

F22-13 (EFIO) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE TRANSPONDER KEY ECU ASSEMBLY

(a) Replace the transponder key ECU assembly with a new one.

Click here

HINT:

Refer to Registration.

Click here

NOTICE:

Key ID code registration is required when the transponder key ECU assembly is replaced.

Click here

NEXT
  1. CHECK WHETHER THE ENGINE STARTS

(a) Using a registered key, turn the ignition switch ON.

(b) Make sure the engine starts 5 seconds after turning the ignition switch ON.

OK:

The engine starts normally.

OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE ECM