Heater / Air Conditioning

Compressor Solenoid Circuit (B1451)

~3min read

DESCRIPTION

In this circuit, the Cooler Compressor Assembly (Compressor Solenoid) receives a refrigerant compression demand signal from the Air Conditioning Amplifier Assembly.

Based on this signal, the Cooler Compressor Assembly (Compressor Solenoid) changes the compression ratio.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

B1451

Compressor Solenoid Circuit

One of the following conditions is met

  • Open in Compressor Solenoid Valve Circuit
  • Short in Compressor Solenoid Valve Circuit
  • Compressor with Pulley Assembly (Compressor Solenoid)
  • Wire harness or connector between the Air Conditioning Amplifier Assembly and the Compressor with Pulley Assembly (Compressor Solenoid)
  • Air Conditioning Amplifier Assembly

-

DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

Ignition Switch in ON position

○

○

Malfunction Status

Open in Compressor Solenoid Valve Circuit

○

-

Short in Compressor Solenoid Valve Circuit

-

○

Detection Duration

30 seconds minimum

30 seconds minimum

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The Air Conditioning Amplifier Assembly stores this DTC if the malfunction occurs during the period of time shown in parentheses.

WIRING DIAGRAM

PROCEDURE

  1. INSPECT COMPRESSOR WITH PULLEY ASSEMBLY (COMPRESSOR SOLENOID)

(a) Disconnect the Cooler Compressor Assembly (Compressor Solenoid) connector.

*a

Component without wire harness connected

(Cooler Compressor Assembly (Compressor Solenoid))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

1 (SOL-) - 2 (SOL+)

25 °C

10,1 à 11,1 Ω

NG

REPLACE COMPRESSOR WITH PULLEY ASSEMBLY (COMPRESSOR SOLENOID)

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

C72-1 (SOL-) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

(a) Disconnect the F139 connector from the air conditioning amplifier assembly.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

C72-2 (SOL+) - F139-3 (SOL+)

Always

Below 1 Ω

C72-2 (SOL+) or F139-3 (SOL+) - Body ground

Always

10 kΩ minimum

Result:

Result

Proceed to

NG

A

OK (when troubleshooting is performed using the Symptom Table)

B

OK (when troubleshooting is performed using DTC)

C

A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

C
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Clear the DTCs.

Click here

Body Electrical > Air Conditioner > Clear DTCs

(b) Check DTCs.

Click here

Body Electrical > Air Conditioner > Trouble Codes

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY