Body (Interior / Exterior / Electrical)

Front Seat

57steps
~342min
4/5difficulty
02040608010058.843N·mlb·ft
Tightening torque found on this page
Done 0 of 57

Contents:

Components and Components Location. On Vehicle Inspection

Components and Components Location

Component

1. Front Seat Assembly
1-a. 44.1 - 59 N·m
2. Headrest
3. Seat Back Garnish
4. Headrest Guide
5. Back board
6. Outer Shield Cover
7. Power Seat Control Switch
8.Seat Back Cover
9. Seat Back Cushion
10. Seat Back Heater
11. Seat Back Frame
11-a 44.1 - 59 N·m
12. Seat Cushion Cover
13. Seat Cushion Pad
14. Seat Cushion Heater
15. Heater Unit
16. Blower Unit
17. Seat Cushion Frame
18. Front Side Airbag [Driver's Side]
19. Front Side Airbag [Passenger's Side]

On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS
  1. The front seat can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details

Front Seat Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Assembly
It can control the seat height by operating the seat cushion power switch (A) as shown below. [Driver's Side] [Passenger's Side]
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the seat assembly after removing the bolts (A).

    Tightening torque : 44.1 - 59 N·m

  3. Disconnect the front seat connectors (A).
Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Seat Back Cover Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Back Cover
  1. Remove the front seat back cover assembly. (Refer to Front Seat - "Front Seat Back Cover Assembly")
  2. Remove the velcro tapes (A) and the hog ring clips (B).
  3. Remove the front seat back cover (A) and front seat back pad (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Seat Back Cover Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Back Cover Assembly
  1. Remove the front seat shield inner cover and outer cover. (Refer to Front Seat - "Front Seat Shield Cover")
  2. Remove the headrest (A).
  3. Remove the headrest guides (A).
  4. Remove the front seat back upper cover cap (A).
  5. Remove the front seat back garnish (A) after removing the screws.
    Clip position :
  6. Remove the front seat back board (A) in the direction of the arrow.
  7. Disconnect the front seat connector (A).
  8. Remove the seat back assembly after removing the bolts (A).
  9. Separate the protector (A).
  10. Remove the front seat back cover assembly (A) from the front seat back frame (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Seat Cushion Cover Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Cushion Cover
  1. Remove the front seat cushion cover assembly. (Refer to Front Seat - "Front Seat Cushion Cover Assembly")
  2. Remove the velcro tapes (A) and the hog ring clips (B).
  3. Remove the front seat cushion cover (A) and front seat cushion pad (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the PODS unit. (S/W Management → Occupant Detection System → Body Sensor Reset)
    After initializing the passenger classification sensor unit, delete the airbag control module and the passenger classification sensor unit fault code (DTC).

Front Seat Cushion Cover Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Cushion Cover Assembly
  1. Remove the front seat shield inner cover and outer cover. (Refer to Front Seat - "Front Seat Shield Cover")
  2. Disconnect the front seat connectors (A).
  3. Remove the seat back assembly after removing the bolts (A).
  4. Separate the protector (A). [Front] [Rear] [Left] [Right]
  5. Remove the front seat cushion inner cover (A).
    Clip position :
  6. Remove the front seat cushion cover assembly (A) from the front seat cushion frame (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the PODS unit. (S/W Management → Occupant Classification System → Zero Re-calibration of Occupant Classification Sensor)
    After initializing the PODS unit, erase DTC regarding the airbag control unit and the PODS unit.

Front Seat Frame Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Back Frame
  1. Remove the Side Airbag (SAB) module. (Refer to Restraint - "Side Airbag (SAB) Module")
  2. Remove the front seat cushion cover assembly. (Refer to Front Seat - "Front Seat Cushion Cover Assembly")
Front Seat Cushion Frame

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the PODS unit. (S/W Management → Occupant Classification System → Zero Re-calibration of Occupant Classification Sensor)
    After readjusting the passenger classification sensor unit, delete the airbag control module and passenger classification sensor unit fault code(DTC).

Front Seat Shield Cover Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Outer Shield Cover
  1. Remove the front seat assembly. (Refer to Front Seat - "Front Seat Assembly")
  2. Remove the cover (A) after removing the screw.
  3. Disconnect the power seat control switch connector (A).
  4. Remove the front seat assembly. (Refer to Front Seat - "Front Seat Assembly")
  5. Remove the cover (A) after removing the screws.
    Clip position :
Inner Shield Cover

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Seat Switch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Seat Control Switch
  1. Remove the front seat outer shield cover. (Refer to Front Seat - "Front Seat Shield Cover")
  2. Remove the switch (A) after removing the screws.
  3. Remove the front driver door trim. (Refer to Front Door - "Front Door Trim")
  4. Remove the switch (A) after removing the screws.
Integrated Memory Seat (IMS) Switch

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Seat Unit Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Integrated Memory Seat (IMS) Unit
  1. Remove the driver's side front seat assembly. (Refer to Front Seat - "Front Seat Assembly")
  2. Disconnect the unit connectors (A).
  3. Remove the unit (A) after removing the screws.
  4. Remove the front seat assembly. (Refer to Front Seat - "Front Seat Assembly")
  5. Disconnect the unit connector (A).
  6. Separate the clamp (A).
  7. Remove the unit (A).
  8. Remove the passenger's side front seat assembly. (Refer to Front Seat - "Front Seat Assembly")
  9. Disconnect the unit connector (A).
  10. Remove the unit (A) after removing the screws.
Blower Unit Heater / Ventilation Unit

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. When replacing the seat unit, perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Lumbar Support Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front seat back cover assembly. (Refer to Front Seat - "Front Seat Back Cover Assembly")
  2. Remove the lumbar support (B) after removing the fasteners (A).
    Clip position :
  3. Disconnect the lumbar support connector (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.