Body (Interior / Exterior / Electrical)

Front & Rear Bumper

42steps
~252min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 42

Contents:

Bumper Mounting Bracket Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Rear Bumper Mounting Bracket [Standard]
  1. Remove the rear bumper assembly. (Refer to Front & Rear Bumper - "Rear Bumper Assembly")
  2. Remove the bracket (A) after removing the screws.
  3. Remove the rear bumper assembly. (Refer to Front & Rear Bumper - "Rear Bumper Assembly")
  4. Remove the bracket (A) after removing the screws.
Rear Bumper Mounting Bracket [Option]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Bumper Assembly Components and Components Location

Component and Component Location

Front Bumper [Removal]
1. Front bumper assembly

Front Bumper [Disassembly]
1. Front Bumper Harness
2. Front Bumper Energy Absorber
3. Front Bumper Active Air Flap
4. Ultra Wide Band Unit
5. Front Ultrasonic Sensor
6. Front Corner Radar
7. Front Corner Ultrasonic Sensor
8. Front Bumper Radiator Grille
9. License Plate
10. Front Bumper Grille Piece
11. Front Bumper Molding
12. Front Bumper Lower Cover
13. Front Bumper Upper Cover

Front Bumper Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Bumper Assembly
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the fender garnish. (Refer to Body Side Molding - "Fender Garnish")
  3. Remove the fasteners (A).
  4. Remove the screw (A) and fasteners (B).
  5. Separate the front bumper assembly (A).
  6. Remove the front bumper assembly after disconnecting the front bumper main connector (A).
  7. Remove the radiator upper cover (A) after removing the fasteners.
    Clip position :
  8. Remove the front bumper assembly.
  9. Remove the radiator upper cover.
  10. Remove the radiator upper grille (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

  11. Disconnect the wide angle front camera connector (A).
  12. Disconnect the front center lamp connector (A). [Option type only]
Radiator Upper Cover Radiator Upper Grille

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Bumper Assembly Disassembly and Reassembly

Disassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front corner radar. (Refer to Advanced Driver Assistance Systems (ADAS) - "Front Corner Radar")
  2. Remove the front bumper wiring harness (A) after removing the fasteners.
    Clip position :
  3. Remove the front bumper energy absorber (A).
    Clip position :
  4. Remove the active air flap. (Refer to Cooling System - "Active Air Flap (AAF)")
  5. Remove the radiator grille (A) after removing the screws.
    Clip position :
  6. Remove the radiator grille (A) after removing the screws.
  7. Remove the front bumper grille piece (A) after removing the screws.
    Clip position :
  8. Remove the front bumper molding (A).
    Clip position :
  9. Separate the front bumper upper cover (A) and lower cover (B) after removing the screw.
    Clip position :

Reassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Bumper Assembly Components and Components Location

Component and Component Location

Rear Bumper [Removal]
1. Rear Bumper Under Cover
1-a. 15.7 - 24 N·m
2. Rear Bumper Rail Assembly
2-a. 15.7 - 24 N·m
3. Rear Bumper Assembly
3-a. 15.7 - 24 N·m
4. Rear Bumper Mounting Bracket
4-a. 6.9 - 10,2 N·m

Rear Bumper [Disassembly]
1. Rear Bumper Harness
2. Rear Bumper Rail Assembly
3. Rear Bumper Reflector
4. Back Up Lamp
5. Rear Ultrasonic Sensor
6. Ultra Wide Band Unit
7. Rear Corner Radar
8. Rear Corner Ultrasonic Sensor
9. Rear Bumper Skid Plate
10. Rear Bumper Side Cover
11. Rear Bumper Cover

Rear Bumper Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the outside rear combination lamp. (Refer to Light & Vision System - "Rear Combination Lamp")
  2. Remove the quarter garnish. (Refer to Body Side Molding - "Quarter Garnish")
  3. Remove the rear bumper under cover (A) after removing the nuts and fasteners.

    Tightening torque : 15.7 - 24 N·m

  4. Remove the screw (A) and fasteners (B).
  5. Remove the bolts (A).

    Tightening torque : 15.7 - 24 N·m

    [Driver's Side] [Passenger's Side]
  6. Remove the rear bumper (A) screws and fasteners. [Driver's Side] [Passenger's Side]
  7. Separate the rear bumper assembly (A).
  8. Disconnect the rear bumper main connector (A).
  9. Remove the rear bumper assembly after disconnecting the rear bumper main connector (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    Rear Corner Radar Type
    • Use only genuine part for the bumper containing the rear corner radar.
    • Do not apply license plate molding or foreign objects such as a bumper sticker or a bumper guard near the radar sensor. Doing so may adversely affect the sensing performance of the radar.
    • The system may not work properly if paint repair is performed near the rear corner radar. Be careful not to use a Polyester putty which has iron content.
    • The system may not work properly if the rear corner radar is covered with foreign matters, such as snow, rain or dirt, etc.
    • The system may not work properly if the bumper around the rear corner radar is damaged or sensor is out of position caused by the impact.
    • When installing the rear bumper, remove the foreign matter attached on the exterior/interior label of the rear bumper. (There must be no mechanical damage near the rear corner radar)

Rear Bumper Assembly Disassembly and Reassembly

Disassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear bumper beam assembly. (Refer to Front & Rear Bumper - "Rear Bumper Beam")
  2. Remove the reflector (A) after removing the screws.
  3. Remove the rear bumper skid plate (A) after removing the screws.
    Clip position :
  4. Remove the rear bumper side cover (A) after removing the screws..
    Clip position :
  5. Remove the rear bumper cover.

Reassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Bumper Beam Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear bumper assembly. (Refer to Front & Rear Bumper - "Rear Bumper Assembly")
  2. Remove the rear bumper wiring harness (A) after removing the fastener.
    Clip position :
  3. Remove the rear bumper beam assembly (A) after removing the fasteners.
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.